YLYifeng Li

Yifeng Li

*This is an algorithmically generated author record based on publicly available information.

Yifeng Li has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Novel Asymmetric Variable Flux Memory Machine With Split-Spoke Structure

    by Qiang Wei, Z. Q. Zhu, Henghui Li, Jianghua Feng, Shuying Guo, Yifeng Li, Shouzhi Feng

    In this paper, a novel asymmetric split-spoke-type (AS) variable flux memory (VFM) machine, featuring an asymmetric permanent magnet configuration, is proposed. It enables a favorable trade-off between the flux regulation (FR) capability for achieving a wide constant power speed range (CPSR) and the magnetic-field-shifting effect for torque improvement. The proposed AS-VFM machine, together with a symmetrical unite-spoke-type VFM machine and a symmetrical split-spoke-type VFM machine, is optimized using a genetic-algorithm-based dual magnetization state optimization method, with particular attention to the inverter current limits. The electromagnetic performance of the three machines with the optimal designs are investigated and compared, confirming that the proposed AS-VFM machine exhibits improved FR capacity and torque output, as well as an extended CPSR and improved overall efficiency. Finally, a prototype of the AS-VFM machine is fabricated and tested for validation.

  • Novel Asymmetric Variable Flux Memory Machines With U-Type PM Configurations

    by Qiang Wei, Z. Q. Zhu, Yinzhao Zheng, Hui Yang, Seyedmilad Kazemisangdehi, Jianghua Feng, Shuying Guo, Yifeng Li, Shouzhi Feng

    In this paper, two novel asymmetric variable flux memory machines with U-type permanent magnet (PM) configurations are proposed. These designs feature variable PMs (VPMs) placed on one side and constant PMs (CPMs) on the opposite side of the U-shaped cavity, with or without additional VPMs in the middle cavity. Both machines are firstly designed and optimized using finite element method with the same 21-slot/4-pole stator and rotor inner/outer diameters. The electromagnetic performance of the optimized designs are analyzed and compared. Results show that the middle VPMs can enhance the flux regulation (FR) capacity but contribute less to the torque. As a result, the machine with the middle VPMs can achieve a wide FR range and improved overall efficiency, whereas the machine without the middle VPMs can deliver higher torque density. Finally, two prototypes are fabricated and tested for validation.

  • A Novel Asymmetric V-Type Variable Flux Memory Machine With Hybrid-Layer Permanent Magnets

    by Qiang Wei, Z. Q. Zhu, Henghui Li, Seyedmilad Kazemisangdehi, Jianghua Feng, Shuying Guo, Yifeng Li, Shouzhi Feng

    In this paper, a novel asymmetric V-type variable flux memory (VFM) machine featuring a hybrid-layer permanent magnet (PM) structure is proposed. This design incorporates two PM arrangements within each pole: one part employs a single-layer variable PM (VPM), while the other part features a dual-layer PM arrangement consisting of a constant PM (CPM) and a VPM. The proposed machine, along with two existing machine topologies: a symmetrical single-layer VFM machine and an asymmetric single-layer VFM machine, is optimized using finite element method with the same stator, rotor diameter, and total PM usage. The electromagnetic performance of the optimized designs for all three machines is investigated and compared. It shows that the asymmetric design can mitigate the intrapolar cross-coupling effect between the CPMs and VPMs found in the symmetrical VFM machine, thereby delivering higher torque output. Furthermore, compared to the asymmetric single-layer VFM machine, the proposed machine can achieve wider flux regulation range and improved overall efficiency due to the series-parallel magnetic circuit enabled by the hybrid-layer structure. Finally, a prototype of the proposed machine is fabricated and tested for validation.


  • Novel Magnetization State Control Method Based on Modified Voltage Limitation for Hybrid Magnet Memory Machine

    by Yan Jia, Z.Q. Zhu, Qiang Wei, Jianghua Feng, Shuying Guo, Yifeng Li, Liang Hu

    This paper proposes a novel magnetization state (MS) control method for a hybrid magnet memory machine (HMMM) based on modified voltage limitation. The effect of the voltage limitation on the MS manipulation is analyzed. The circumcircle of voltage vector hexagon is utilized as the modified voltage limitation instead of the inscribed circle to simplify the algorithm which can increase the voltage margin for MS manipulation under the same operating conditions. The maximum amplitude of the magnetizing current pulse under real-time voltage limitation can be calculated and utilized as the boundary for MS manipulation. Within the boundary, the target MS can be achieved. When the MS is limited, the proposed MS control method also provides a solution to achieve the target MS by calculating the optimal operating speed. The experimental validations are carried out on the HMMM control system to verify the feasibility of the proposed MS control method.

  • Initial Temperature Determination for Real-Time Thermal Models in Permanent Magnet Synchronous Machines

    by Dawei Liang, Z. Q. Zhu, Jianghua Feng, Yifeng Li, Shuying Guo

    The applications of real-time thermal models (RTTMs) to sensorless temperature monitoring are limited due to unknown initial temperatures. To address this issue, this paper proposes a method to determine initial temperatures for all main components, only relying on one thermal sensor installed in a specific component, ideally in the active or end windings, where the measurement practicality and the signal-to-noise ratio in the initial temperature estimation process are all considered. In the proposed method, the measured temperature of the specific component in each sampling step is integrated into the RTTM to predict its next-step temperature, and thus, its temperature deviations between the predicted and measured values contain the initial temperature information of the other critical components. Based on several sampling steps, their initial temperatures can be estimated with high estimation accuracy. Afterwards, the estimated initial temperatures can be used to correct the temperature states of the employed RTTM, and thus, the temperature errors caused by the inaccurate initial temperatures can be eliminated in a short time. The proposed method is applied to a well-trained four-order RTTM for an interior permanent magnet synchronous machine and validated experimentally.


  • Novel Magnetization State Closed-Loop Control for Variable Flux Memory Machine

    by Yan Jia, Z.Q. Zhu, Lei Xu, Jianghua Feng, Shuying Guo, Yifeng Li, Liang Hu

    In this paper, a novel magnetization state (MS) control method is proposed by utilizing torque deviation to achieve the MS closed-loop control for variable flux memory machine. Firstly, the relationship between the MSs and the demand magnetizing current pulses is built into a look-up table, which also contains information on the flux linkages and the dq-axis inductances under different MSs. Afterwards, a model-based torque calculation is adopted for torque estimation, and then, the torque deviation between the present MS and the target MS can be obtained and utilized to generate the MS switch signal, which will determine the type of MS manipulation. Subsequently, the calculated torque will also be used for real-time monitoring of MS. The feasibility of the proposed MS control method is verified by simulation. Finally, experiments are carried out on a hybrid magnet memory machine control system for validation.


  • A Novel Dual Magnetizing Current Controller to Mitigate Speed Fluctuation During Magnetization State Manipulation for Variable Flux Memory Machines

    by Yan Jia, Z. Q. Zhu, Qiang Wei, Jianghua Feng, Shuying Guo, Yifeng Li, Liang Hu

    This paper proposes a novel dual magnetizing current controller for variable flux memory machines (VFMMs) aiming to mitigate the speed fluctuation during magnetization state manipulation. Firstly, the magnetizing properties of the investigated hybrid magnet synchronous memory machine (HMSMM) are tested and researched offline. The effect of amplitude and time duration of the magnetizing current pulse on its magnetizing capability is investigated. Secondly, based on the dynamic mathematical model, a q-axis current pulse is injected to compensate the torque fluctuation caused by the d-axis magnetizing current pulse, which forms a dual magnetizing current controller during magnetization state manipulation. Then, the experiments are carried out on the investigated HMSMM control system. The measured results of the transient performance on both remagnetization and demagnetization show that the proposed dual magnetizing current controller can significantly mitigate the speed fluctuation and has better transient performance than the conventional single magnetizing current method.


  • A Hybrid Lumped-Parameter and Two-Dimensional Analytical Thermal Model for Electrical Machines

    by Dawei Liang, Z. Q. Zhu, Yafeng Zhang, Jianghua Feng, Shuying Guo, Yifeng Li, Jiangquan Wu, Anfeng Zhao

    The lumped-parameter thermal network (LPTN) has been widely used in the thermal analysis for electrical machines. Nevertheless, since the thermal resistances are defined based on the 1-dimensional heat transfer equation, it will cause misestimation of the average temperatures when the thermal model extends to 2-dimensions or 3-dimensions. In this paper, a hybrid thermal model utilizing the synergies of LPTN and 2-D analytical thermal models is developed to address this issue and to predict accurate critical temperatures, especially average and maximum temperatures of the active- and end-windings. The 2-D analytical thermal models are obtained by solving the Poisson's equations with the Dirichlet boundary conditions extracted from the LPTN. The derived analytical solutions are expressed as Fourier series, which can be further simplified by utilizing the first term only to represent average and maximum temperatures with sufficient accuracy and short computation time. The hybrid thermal model is applied to a totally enclosed forced convection permanent magnet synchronous machine and validated by numerical techniques and experiments.