Liang Hu
Research Subjects
Liang Hu has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Jianghua Feng
CRRC Zhuzhou Institute Company Ltd., Zhuzhou, China
4 shared publications - Shuying Guo
CRRC Zhuzhou Institute Company Ltd., Zhuzhou, China
4 shared publications - Yan Jia
Department of Electronic and Electrical Engineering, University of Sheffield, Sheffield, U.K.
4 shared publications - Zi Qiang Zhu
Department of Electrical and Electronic Engineering, The Hong Kong Polytechnic University, Hong Kong, China
4 shared publications - Yifeng Li
CRRC Zhuzhou Institute Company Ltd., Zhuzhou, China
3 shared publications - Haitao Liu
The School of Traffic and Transportation Engineering, Central South University, Changsha 410075, China
2 shared publications
Latest Publications
- 25 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (5) , 6712-6721
Adaptive Efficiency Optimization Control of VLF-PM Motors Considering Operation Uncertainties With DCEE
For the mechatronic system of variable leakage flux-permanent magnet (VLF-PM) motors, motor parameters that vary with uncertain operating conditions lead to reduced control efficiency, which fails to meet the requirements of energy management. To solve this problem, an adaptive efficiency optimization control (EOC) considering operation uncertainties with enhanced dual control for exploration and exploitation (DCEE) is innovatively proposed. First, an N-dimensional flux linkage estimator is designed, which enables the quantification of the uncertainty of parameter variations caused by external operating conditions. Additionally, an optimization rule with dual effects is established based on the estimated N-dimensional flux linkage distribution, allowing the optimal current angle to adapt to different external operating conditions. With this method, the impact caused by errors in traditional parameter estimation is overcome. Meanwhile, model-based active uncertainty learning avoids the training of large amounts of data and eliminates a significant computational burden. Finally, a comparison is made with existing EOC methods, which proves the effectiveness and advantages of the proposed method.
- 25 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (5) , 6712-6721
Adaptive Efficiency Optimization Control of VLF-PM Motors Considering Operation Uncertainties With DCEE
For the mechatronic system of variable leakage flux-permanent magnet (VLF-PM) motors, motor parameters that vary with uncertain operating conditions lead to reduced control efficiency, which fails to meet the requirements of energy management. To solve this problem, an adaptive efficiency optimization control (EOC) considering operation uncertainties with enhanced dual control for exploration and exploitation (DCEE) is innovatively proposed. First, an N-dimensional flux linkage estimator is designed, which enables the quantification of the uncertainty of parameter variations caused by external operating conditions. Additionally, an optimization rule with dual effects is established based on the estimated N-dimensional flux linkage distribution, allowing the optimal current angle to adapt to different external operating conditions. With this method, the impact caused by errors in traditional parameter estimation is overcome. Meanwhile, model-based active uncertainty learning avoids the training of large amounts of data and eliminates a significant computational burden. Finally, a comparison is made with existing EOC methods, which proves the effectiveness and advantages of the proposed method.
- Open Access
Correction: Liu et al. Junction Temperature Control of a Traction Inverter Based on Three-Level Active Neutral Point-Clamping. Energies 2025, 18, 2241
The authors wish to make the following corrections to this paper
Open AccessCorrection: Liu et al. Junction Temperature Control of a Traction Inverter Based on Three-Level Active Neutral Point-Clamping. Energies 2025, 18, 2241
The authors wish to make the following corrections to this paper
- Open Access
Junction Temperature Control of a Traction Inverter Based on Three-Level Active Neutral Point-Clamping
In this study, we propose an active junction temperature control method specifically tailored for traction inverters based on active neutral point-clamped (ANPC) three-level topology. This approach not only enables real-time junction temperature equalization across switching devices, but also minimizes switching losses while preserving synchronous modulation. The methodology begins with a detailed formulation of the loss quantification model for ANPC inverters, establishing the relationship between predicted losses and switching vectors. Building on this foundation, we develop a loss equalization modulation control strategy featuring closed-loop loss control. The effectiveness and practicality of the proposed control method are rigorously validated using simulations and low-power experimental testing, demonstrating its potential to enhance both the reliability and efficiency of traction inverters.
Open AccessJunction Temperature Control of a Traction Inverter Based on Three-Level Active Neutral Point-Clamping
In this study, we propose an active junction temperature control method specifically tailored for traction inverters based on active neutral point-clamped (ANPC) three-level topology. This approach not only enables real-time junction temperature equalization across switching devices, but also minimizes switching losses while preserving synchronous modulation. The methodology begins with a detailed formulation of the loss quantification model for ANPC inverters, establishing the relationship between predicted losses and switching vectors. Building on this foundation, we develop a loss equalization modulation control strategy featuring closed-loop loss control. The effectiveness and practicality of the proposed control method are rigorously validated using simulations and low-power experimental testing, demonstrating its potential to enhance both the reliability and efficiency of traction inverters.
- 11 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (5) , 6976-6987
Novel Magnetization State Control Method Utilizing d-Axis Current to Eliminate Unintentional Demagnetization of Low-Coercive Force PM for Variable Flux Memory Machine
This paper proposes a novel magnetization state (MS) control method to eliminate the unintentional demagnetization (UD) of low-coercive force permanent magnet (PM) for variable flux memory machine (VFMM). In the proposed method, the amplitude of demagnetization d-axis current pulse is determined from a look-up table with the relationship between the demagnetization d-axis current pulse and the intersections of torque-speed curves under different MSs, and subsequently used as the condition for the MS manipulation. A PM flux linkage observer is adopted to monitor the UD all the time and the amplitude of d-axis current is controlled without exceeding the amplitude of the demand demagnetization d-axis current pulse to avoid the UD in the whole speed range. The inverter nonlinearity is compensated to improve the estimation accuracy of the PM linkage flux. The experiment validation is conducted on a hybrid magnet memory machine system to illustrate the UD issue and to verify the PM flux linkage estimation method and the proposed MS control method.
- 11 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (5) , 6976-6987
Novel Magnetization State Control Method Utilizing d-Axis Current to Eliminate Unintentional Demagnetization of Low-Coercive Force PM for Variable Flux Memory Machine
This paper proposes a novel magnetization state (MS) control method to eliminate the unintentional demagnetization (UD) of low-coercive force permanent magnet (PM) for variable flux memory machine (VFMM). In the proposed method, the amplitude of demagnetization d-axis current pulse is determined from a look-up table with the relationship between the demagnetization d-axis current pulse and the intersections of torque-speed curves under different MSs, and subsequently used as the condition for the MS manipulation. A PM flux linkage observer is adopted to monitor the UD all the time and the amplitude of d-axis current is controlled without exceeding the amplitude of the demand demagnetization d-axis current pulse to avoid the UD in the whole speed range. The inverter nonlinearity is compensated to improve the estimation accuracy of the PM linkage flux. The experiment validation is conducted on a hybrid magnet memory machine system to illustrate the UD issue and to verify the PM flux linkage estimation method and the proposed MS control method.
- 9 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (1) , 172-184
Novel Magnetization State Control Method Based on Modified Voltage Limitation for Hybrid Magnet Memory Machine
This paper proposes a novel magnetization state (MS) control method for a hybrid magnet memory machine (HMMM) based on modified voltage limitation. The effect of the voltage limitation on the MS manipulation is analyzed. The circumcircle of voltage vector hexagon is utilized as the modified voltage limitation instead of the inscribed circle to simplify the algorithm which can increase the voltage margin for MS manipulation under the same operating conditions. The maximum amplitude of the magnetizing current pulse under real-time voltage limitation can be calculated and utilized as the boundary for MS manipulation. Within the boundary, the target MS can be achieved. When the MS is limited, the proposed MS control method also provides a solution to achieve the target MS by calculating the optimal operating speed. The experimental validations are carried out on the HMMM control system to verify the feasibility of the proposed MS control method.
- 9 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (1) , 172-184
Novel Magnetization State Control Method Based on Modified Voltage Limitation for Hybrid Magnet Memory Machine
This paper proposes a novel magnetization state (MS) control method for a hybrid magnet memory machine (HMMM) based on modified voltage limitation. The effect of the voltage limitation on the MS manipulation is analyzed. The circumcircle of voltage vector hexagon is utilized as the modified voltage limitation instead of the inscribed circle to simplify the algorithm which can increase the voltage margin for MS manipulation under the same operating conditions. The maximum amplitude of the magnetizing current pulse under real-time voltage limitation can be calculated and utilized as the boundary for MS manipulation. Within the boundary, the target MS can be achieved. When the MS is limited, the proposed MS control method also provides a solution to achieve the target MS by calculating the optimal operating speed. The experimental validations are carried out on the HMMM control system to verify the feasibility of the proposed MS control method.
- 13 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (3) , 3964-3977
Novel Magnetization State Closed-Loop Control for Variable Flux Memory Machine
In this paper, a novel magnetization state (MS) control method is proposed by utilizing torque deviation to achieve the MS closed-loop control for variable flux memory machine. Firstly, the relationship between the MSs and the demand magnetizing current pulses is built into a look-up table, which also contains information on the flux linkages and the dq-axis inductances under different MSs. Afterwards, a model-based torque calculation is adopted for torque estimation, and then, the torque deviation between the present MS and the target MS can be obtained and utilized to generate the MS switch signal, which will determine the type of MS manipulation. Subsequently, the calculated torque will also be used for real-time monitoring of MS. The feasibility of the proposed MS control method is verified by simulation. Finally, experiments are carried out on a hybrid magnet memory machine control system for validation.
- 13 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (3) , 3964-3977
Novel Magnetization State Closed-Loop Control for Variable Flux Memory Machine
In this paper, a novel magnetization state (MS) control method is proposed by utilizing torque deviation to achieve the MS closed-loop control for variable flux memory machine. Firstly, the relationship between the MSs and the demand magnetizing current pulses is built into a look-up table, which also contains information on the flux linkages and the dq-axis inductances under different MSs. Afterwards, a model-based torque calculation is adopted for torque estimation, and then, the torque deviation between the present MS and the target MS can be obtained and utilized to generate the MS switch signal, which will determine the type of MS manipulation. Subsequently, the calculated torque will also be used for real-time monitoring of MS. The feasibility of the proposed MS control method is verified by simulation. Finally, experiments are carried out on a hybrid magnet memory machine control system for validation.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (3) , 1904-1918
A Novel Dual Magnetizing Current Controller to Mitigate Speed Fluctuation During Magnetization State Manipulation for Variable Flux Memory Machines
This paper proposes a novel dual magnetizing current controller for variable flux memory machines (VFMMs) aiming to mitigate the speed fluctuation during magnetization state manipulation. Firstly, the magnetizing properties of the investigated hybrid magnet synchronous memory machine (HMSMM) are tested and researched offline. The effect of amplitude and time duration of the magnetizing current pulse on its magnetizing capability is investigated. Secondly, based on the dynamic mathematical model, a q-axis current pulse is injected to compensate the torque fluctuation caused by the d-axis magnetizing current pulse, which forms a dual magnetizing current controller during magnetization state manipulation. Then, the experiments are carried out on the investigated HMSMM control system. The measured results of the transient performance on both remagnetization and demagnetization show that the proposed dual magnetizing current controller can significantly mitigate the speed fluctuation and has better transient performance than the conventional single magnetizing current method.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (3) , 1904-1918
A Novel Dual Magnetizing Current Controller to Mitigate Speed Fluctuation During Magnetization State Manipulation for Variable Flux Memory Machines
This paper proposes a novel dual magnetizing current controller for variable flux memory machines (VFMMs) aiming to mitigate the speed fluctuation during magnetization state manipulation. Firstly, the magnetizing properties of the investigated hybrid magnet synchronous memory machine (HMSMM) are tested and researched offline. The effect of amplitude and time duration of the magnetizing current pulse on its magnetizing capability is investigated. Secondly, based on the dynamic mathematical model, a q-axis current pulse is injected to compensate the torque fluctuation caused by the d-axis magnetizing current pulse, which forms a dual magnetizing current controller during magnetization state manipulation. Then, the experiments are carried out on the investigated HMSMM control system. The measured results of the transient performance on both remagnetization and demagnetization show that the proposed dual magnetizing current controller can significantly mitigate the speed fluctuation and has better transient performance than the conventional single magnetizing current method.
- Open Access
A Refined DER-Level Transient Stability Prediction Method Considering Time-Varying Spatial–Temporal Correlations in Microgrids
The transient responses of distributed energy resources (DERs) in a microgrid are dynamically correlated in spatial and temporal dimensions. Hence, the transient stability prediction in microgrids would require an effective modeling of time-varying correlations and the mining of spatial–temporal features of electrical data. This paper proposes a refined DER-level transient stability prediction method for microgrids considering the time-varying spatial–temporal correlations of DERs. First, the spatial–temporal dynamic correlation of DERs was extracted and modeled by an attention-based mechanism. Then, a spatial–temporal graph convolution network was proposed to predict the dynamics of unstable DERs and the instability severity trend in a microgrid. The TSP model consisted of three parts: (1) several stacked spatial–temporal convolution modules to simultaneously mine the spatial–temporal dynamic features of microgrids, (2) an unstable DER identification module to predict the microgrid system stability and identify unstable DERs, and (3) an instability severity trend prediction module for DERs in a microgrid. The test results on a realistic 16-bus 10-DER microgrid demonstrated that the proposed prediction method possessed the desirable reliability and interpretability and outperformed the state-of-the-art baselines in unstable DER identifications and DER instability severity trend predictions.
Open AccessA Refined DER-Level Transient Stability Prediction Method Considering Time-Varying Spatial–Temporal Correlations in Microgrids
The transient responses of distributed energy resources (DERs) in a microgrid are dynamically correlated in spatial and temporal dimensions. Hence, the transient stability prediction in microgrids would require an effective modeling of time-varying correlations and the mining of spatial–temporal features of electrical data. This paper proposes a refined DER-level transient stability prediction method for microgrids considering the time-varying spatial–temporal correlations of DERs. First, the spatial–temporal dynamic correlation of DERs was extracted and modeled by an attention-based mechanism. Then, a spatial–temporal graph convolution network was proposed to predict the dynamics of unstable DERs and the instability severity trend in a microgrid. The TSP model consisted of three parts: (1) several stacked spatial–temporal convolution modules to simultaneously mine the spatial–temporal dynamic features of microgrids, (2) an unstable DER identification module to predict the microgrid system stability and identify unstable DERs, and (3) an instability severity trend prediction module for DERs in a microgrid. The test results on a realistic 16-bus 10-DER microgrid demonstrated that the proposed prediction method possessed the desirable reliability and interpretability and outperformed the state-of-the-art baselines in unstable DER identifications and DER instability severity trend predictions.