Antonio José Lorente-López
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Antonio José Lorente-López has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- José Enrique Gutiérrez-Romero
Department of Naval Architecture Technology, Universidad Politécnica de Cartagena, Paseo Alfonso XIII 52, 30203 Cartagena, Spain
4 shared publications - Pablo Romero-Tello
Departamento de Fisica Aplicada y Tecnología Naval, Universidad Politecnica de Cartagena, Cartagena, Spain
4 shared publications - Alejandro López-Belchí
Applied Physics and Naval Technology Department, Universidad Politécnica de Cartagena, Paseo Alfonso XIII, 52, 30203 Cartagena, Murcia, Spain
1 shared publication B. Servan
Applied Physics and Naval Technology Department Universidad Politécnica de Cartagena (UPCT) Paseo Alfonso XIII, 52, 30203 Cartagena, Spain
1 shared publication- Blas Zamora
Department of Thermal and Fluids Engineering, Universidad Politécnica de Cartagena, Paseo Alfonso XIII 52, 30203 Cartagena, Spain
1 shared publication - Borja Servan-Camas
Centre Internacional de Métodes Numérics en Enginyeria (CIMNE), Gran Capitán s/n, 08034 Barcelona, Spain
1 shared publication
Latest Publications
- Open Access
- 4 February 2026
- Published by Elsevier in Marine Structures
- Vol. 108
Accelerated fully coupled hydro-elastic analysis of ships using a combined full and modal-reduced FEM approach
- 4 February 2026
- Published by Elsevier in Marine Structures
- Vol. 108
Open AccessAccelerated fully coupled hydro-elastic analysis of ships using a combined full and modal-reduced FEM approach
- 1 January 2025
- Published by Emerald Publishing in International Journal of Structural Integrity
- Vol. 16 (1) , 60-84
Structural design optimization of pressure hull using genetic algorithm and finite element analysis
Purpose: The main objective is to develop a new design methodology for pressure hulls, prioritizing steel weight reduction without compromising structural safety. Genetic algorithms (GA) will be employed to optimize the structural weight of the hull of a pressure vessel, considering the Det Norske Veritas (DNV) standard formulation. This includes optimizing both the scantling of the pressure hull and the dimensions of the frames while complying with constraints based on the DNV regulation: nominal, over-immersion and collapse pressures. The proposed solution will be analyzed using finite element analysis (FEA) to verify that the obtained scantlings meet the design requirements.Design/methodology/approach: An optimization of the design parameters of the structure of a pressure hull based on GA is proposed. The starting point is individuals randomly generated by combining the different values that each parameter will take. The surviving designs will be required to meet DNV standards and will be ranked according to the structural weight of each design. Prevailing will be those genes that make designs that comply with the standards and are less heavy. Finally, the feasibility of the design proposed by the GA will be tested by FEM.Findings: The structural integrity of the design resulting from the application of GA (which complies with DNV regulations) has been evaluated by means of FEM considering different constructive defects. In summary, the proposed methodology combined with GA provides a preliminary design of the pressurized hull in a fast way, ensuring compliance with the structural requirements according to the current regulations. Furthermore, this design is optimized in terms of its own weight. The reduction in structural weight provides a reserve of buoyancy that can be used to increase other weight categories, thus extending the operating time of the pressure vessel.Originality/value: This novel approach allows to quickly obtain a preliminary design of a pressure hull structure optimized for minimum weight and ensuring compliance with classification societies. The proposed methodology provides the user with a preliminary design with lower material cost and allows the increase of other weight items.
- 1 January 2025
- Published by Emerald Publishing in International Journal of Structural Integrity
- Vol. 16 (1) , 60-84
Structural design optimization of pressure hull using genetic algorithm and finite element analysis
Purpose: The main objective is to develop a new design methodology for pressure hulls, prioritizing steel weight reduction without compromising structural safety. Genetic algorithms (GA) will be employed to optimize the structural weight of the hull of a pressure vessel, considering the Det Norske Veritas (DNV) standard formulation. This includes optimizing both the scantling of the pressure hull and the dimensions of the frames while complying with constraints based on the DNV regulation: nominal, over-immersion and collapse pressures. The proposed solution will be analyzed using finite element analysis (FEA) to verify that the obtained scantlings meet the design requirements.Design/methodology/approach: An optimization of the design parameters of the structure of a pressure hull based on GA is proposed. The starting point is individuals randomly generated by combining the different values that each parameter will take. The surviving designs will be required to meet DNV standards and will be ranked according to the structural weight of each design. Prevailing will be those genes that make designs that comply with the standards and are less heavy. Finally, the feasibility of the design proposed by the GA will be tested by FEM.Findings: The structural integrity of the design resulting from the application of GA (which complies with DNV regulations) has been evaluated by means of FEM considering different constructive defects. In summary, the proposed methodology combined with GA provides a preliminary design of the pressurized hull in a fast way, ensuring compliance with the structural requirements according to the current regulations. Furthermore, this design is optimized in terms of its own weight. The reduction in structural weight provides a reserve of buoyancy that can be used to increase other weight categories, thus extending the operating time of the pressure vessel.Originality/value: This novel approach allows to quickly obtain a preliminary design of a pressure hull structure optimized for minimum weight and ensuring compliance with classification societies. The proposed methodology provides the user with a preliminary design with lower material cost and allows the increase of other weight items.
- Open Access
- 24 September 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (10) , 1691
Notes on Towed Self-Propulsion Experiments with Simulated Managed Ice in Traditional Towing Tanks
Efficiency estimation of a propeller behind a vessel’s hull while sailing through ice floes, together with the ship’s resistance to motion, is a key factor in designing the power plant and determining the safety measures of a ship. This paper encloses the results from the experiments conducted at the CEHINAV towing tank, which consisted of analyzing the influence of the concentration at the free surface of artificial blocks, simulating ice, in propeller–block interactions. Thrust and torque were measured for a towed self-propelled ship model through simulated broken ice blocks made of paraffin wax. Three block concentrations of different block sizes and three model speeds were studied during the experimentation. Open-water self-propulsion tests and artificial broken ice towed self-propulsion tests are shown and compared in this work. The most relevant observations are outlined at the end of this paper, as well as some guidelines for conducting artificial ice-towed self-propulsion tests in traditional towing tanks.
- 24 September 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (10) , 1691
Open AccessNotes on Towed Self-Propulsion Experiments with Simulated Managed Ice in Traditional Towing Tanks
Efficiency estimation of a propeller behind a vessel’s hull while sailing through ice floes, together with the ship’s resistance to motion, is a key factor in designing the power plant and determining the safety measures of a ship. This paper encloses the results from the experiments conducted at the CEHINAV towing tank, which consisted of analyzing the influence of the concentration at the free surface of artificial blocks, simulating ice, in propeller–block interactions. Thrust and torque were measured for a towed self-propelled ship model through simulated broken ice blocks made of paraffin wax. Three block concentrations of different block sizes and three model speeds were studied during the experimentation. Open-water self-propulsion tests and artificial broken ice towed self-propulsion tests are shown and compared in this work. The most relevant observations are outlined at the end of this paper, as well as some guidelines for conducting artificial ice-towed self-propulsion tests in traditional towing tanks.
- 29 June 2024
- Published by Springer Nature
- p. 81-86
High Fidelity Hydroelastic Model Applied to a Vessel Using MMR
- 29 June 2024
- Published by Springer Nature
- p. 81-86
High Fidelity Hydroelastic Model Applied to a Vessel Using MMR
- Open Access
- 1 January 2023
- Published by Scipedia, S.L.
- Vol. Artificial
Optimisation of ship form based on seakeeping behaviour using Machine Learning
- 1 January 2023
- Published by Scipedia, S.L.
- Vol. Artificial
Open AccessOptimisation of ship form based on seakeeping behaviour using Machine Learning