Giorgio Montinaro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giorgio Montinaro has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Daniele Versaci
Department of Applied Science and Technology, Politecnico di Torino, Corso Duca Degli Abruzzi 24, 10129 Torino, Italy
3 shared publications - Federico Bella
Department of Applied Science and Technology Politecnico di Torino Turin Italy
3 shared publications Silvia Bodoardo
Department of Applied Science and Technology Politecnico di Torino Turin Italy
3 shared publications- Carlotta Francia
Department of Applied Science and Technology, Politecnico di Torino, Corso Duca Degli Abruzzi 24, 10129 Torino, Italy
2 shared publications Julia Amici
2 shared publications- Elisa Ravesio
Department of Applied Science and Technology (DISAT) Politecnico di Torino Turin Italy
1 shared publication
Latest Publications
- Open Access
- 25 September 2026
- Published by Wiley in Small Science
- Vol. 6 (9) , e70406
Unlocking High‐Voltage Aqueous LiNi 0.5 Mn 1.5 O 4 Cathodes Through Binder‐Collector Interfacial Design
Lithium‐ion battery performance and sustainability increasingly depend on “inactive” components such as polymer binders and current collectors. Replacing conventional N‐methyl‐2‐pyrrolidone/polyvinylidene fluoride processing with water‐based manufacturing requires binders that combine mechanical cohesion, interfacial stability, and ionic transport, together with current collectors resistant to corrosion and high‐voltage degradation. Here, two aqueous binder formulations—sodium carboxymethyl cellulose (NaCMC) + SX8684(A)‐64 and NaCMC + TRD202A—are investigated in LiNi 0 . 5 Mn 1 . 5 O 4 (LNMO) cathodes cast on bare and carbon‐coated aluminum foils. Spectroscopic and thermogravimetric analyses identify SX8684(A)‐64 as a single‐phase polymethacrylate with minimal swelling (~2%–3% mass uptake), whereas TRD202A exhibits a hybrid acrylic/fluoropolymer architecture, multistage degradation, and pronounced gel‐like swelling (>30%). Morphological analysis shows porosities of 67%–71% and tortuosities of 2.4–3.7, with TRD202A on carbon‐coated aluminum producing the most open and least tortuous architecture. Intermittent current interruption measurements confirm that this configuration provides the lowest resistance, while delivering >100 mAh g −1 at 5 C, >45 mAh g −1 at 15 C, and >80% capacity retention over 100 cycles. These results demonstrate the importance of co‐designing binder chemistry and current‐collector surfaces for scalable, sustainable aqueous LNMO cathodes.
- 25 September 2026
- Published by Wiley in Small Science
- Vol. 6 (9) , e70406
Open AccessUnlocking High‐Voltage Aqueous LiNi 0.5 Mn 1.5 O 4 Cathodes Through Binder‐Collector Interfacial Design
Lithium‐ion battery performance and sustainability increasingly depend on “inactive” components such as polymer binders and current collectors. Replacing conventional N‐methyl‐2‐pyrrolidone/polyvinylidene fluoride processing with water‐based manufacturing requires binders that combine mechanical cohesion, interfacial stability, and ionic transport, together with current collectors resistant to corrosion and high‐voltage degradation. Here, two aqueous binder formulations—sodium carboxymethyl cellulose (NaCMC) + SX8684(A)‐64 and NaCMC + TRD202A—are investigated in LiNi 0 . 5 Mn 1 . 5 O 4 (LNMO) cathodes cast on bare and carbon‐coated aluminum foils. Spectroscopic and thermogravimetric analyses identify SX8684(A)‐64 as a single‐phase polymethacrylate with minimal swelling (~2%–3% mass uptake), whereas TRD202A exhibits a hybrid acrylic/fluoropolymer architecture, multistage degradation, and pronounced gel‐like swelling (>30%). Morphological analysis shows porosities of 67%–71% and tortuosities of 2.4–3.7, with TRD202A on carbon‐coated aluminum producing the most open and least tortuous architecture. Intermittent current interruption measurements confirm that this configuration provides the lowest resistance, while delivering >100 mAh g −1 at 5 C, >45 mAh g −1 at 15 C, and >80% capacity retention over 100 cycles. These results demonstrate the importance of co‐designing binder chemistry and current‐collector surfaces for scalable, sustainable aqueous LNMO cathodes.
- Open Access
- 31 March 2026
- Published by Elsevier in Journal of Cleaner Production
- Vol. 554
Optimization of binary binder blends for aqueous-based slurries of SiOx/C for next-generation lithium-ion batteries
- 31 March 2026
- Published by Elsevier in Journal of Cleaner Production
- Vol. 554
Open AccessOptimization of binary binder blends for aqueous-based slurries of SiOx/C for next-generation lithium-ion batteries
- Open Access
- 24 June 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 613
Tailoring cathode materials: A comprehensive study on LNMO/LFP blending for next generation lithium-ion batteries
- 24 June 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 613
Open AccessTailoring cathode materials: A comprehensive study on LNMO/LFP blending for next generation lithium-ion batteries