Courtney N. Truelock
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Courtney N. Truelock has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Chad B. Paulk
Kansas State University
3 shared publications - Charles R. Stark
Kansas State University
3 shared publications J. W. Wilson
3 shared publicationsN. E. Ward
3 shared publications- A. Yoder
Kansas State University Manhattan
1 shared publication C. B. Paulk
1 shared publication
Latest Publications
- Open Access
- 1 January 2022
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 8 (11) , 6
Effects of Dietary Amino Acid Density and Exogenous Protease Inclusion on Growth Performance and Apparent Ileal Amino Acid Digestibility in Turkeys
Protein is one of the most expensive nutrients in poultry diets. In an effort to minimize feed costs, protein digestion and utilization by the animal must be carried out as efficiently as possible. The objective of this experiment was to evaluate the effects of dietary amino acid density and exogenous protease inclusion on growth performance and amino acid digestibility in turkey poults. Hybrid turkey poults (n = 780) were fed diets formulated to provide low (LAA) or adequate (AAA) amino acid density (approximately 91 and 100% of the NRC4 recommended requirement for digestible Lys, respectively) with each diet being fed with or without an exogenous protease. Poults received experimental diets from d 1 to 42 of age. Growth performance metrics were calculated from pen weights and feed consumption was recorded throughout each experiment, and digestibility data were obtained from analysis of ileal contents. Data were analyzed using SAS 9.4 with pen as the experimental unit and pen location as the blocking factor. For the overall experiment (d 0 to 42), poults fed AAA diets had improved (P < 0.01) ADG, ADFI, and feed conversion ratio (FCR) compared to those fed LAA diets. There was no difference (P > 0.14) in poult performance due to protease inclusion. There was an amino acid density × protease interaction (P = 0.01) for apparent ileal amino acid digestibility (AIAAD) of Trp. There was no difference in AIAAD coefficients of Trp in the LAA diets with or without protease. However, in the AAA diets, poults not receiving protease had greater AIAAD of Trp than those consuming protease. There was no difference (P > 0.09) in AIAAD coefficients of Arg, Met, Cys, Thr, Ile, Leu, Lys, or Val due to dietary amino acid density or protease inclusion. Greater amino acid density improved growth performance in poults up to 42 d of age. No improvement in growth performance was observed when poults were fed an exogenous protease in the starter phase, although protease inclusion increased ADG by 5.3% and ADFI by 4.1% during the grower phase. There was no benefit of increased dietary amino acid density or protease inclusion on AIAAD in poults.
- 1 January 2022
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 8 (11) , 6
Open AccessEffects of Dietary Amino Acid Density and Exogenous Protease Inclusion on Growth Performance and Apparent Ileal Amino Acid Digestibility in Turkeys
Protein is one of the most expensive nutrients in poultry diets. In an effort to minimize feed costs, protein digestion and utilization by the animal must be carried out as efficiently as possible. The objective of this experiment was to evaluate the effects of dietary amino acid density and exogenous protease inclusion on growth performance and amino acid digestibility in turkey poults. Hybrid turkey poults (n = 780) were fed diets formulated to provide low (LAA) or adequate (AAA) amino acid density (approximately 91 and 100% of the NRC4 recommended requirement for digestible Lys, respectively) with each diet being fed with or without an exogenous protease. Poults received experimental diets from d 1 to 42 of age. Growth performance metrics were calculated from pen weights and feed consumption was recorded throughout each experiment, and digestibility data were obtained from analysis of ileal contents. Data were analyzed using SAS 9.4 with pen as the experimental unit and pen location as the blocking factor. For the overall experiment (d 0 to 42), poults fed AAA diets had improved (P < 0.01) ADG, ADFI, and feed conversion ratio (FCR) compared to those fed LAA diets. There was no difference (P > 0.14) in poult performance due to protease inclusion. There was an amino acid density × protease interaction (P = 0.01) for apparent ileal amino acid digestibility (AIAAD) of Trp. There was no difference in AIAAD coefficients of Trp in the LAA diets with or without protease. However, in the AAA diets, poults not receiving protease had greater AIAAD of Trp than those consuming protease. There was no difference (P > 0.09) in AIAAD coefficients of Arg, Met, Cys, Thr, Ile, Leu, Lys, or Val due to dietary amino acid density or protease inclusion. Greater amino acid density improved growth performance in poults up to 42 d of age. No improvement in growth performance was observed when poults were fed an exogenous protease in the starter phase, although protease inclusion increased ADG by 5.3% and ADFI by 4.1% during the grower phase. There was no benefit of increased dietary amino acid density or protease inclusion on AIAAD in poults.
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 28
Effect of Steam Pressure and Conditioning Temperature During the Pelleting Process on Phytase Stability
This experiment was designed to evaluate the effects of steam pressure and conditioning temperature on the stability of microbial phytase. Treatments were arranged as a 2 × 3 factorial of steam pressure (24 and 44 psi) and conditioning temperature (170, 180, and 190°F). Phytase was added to a corn-soybean meal-based diet and mash samples were collected for phytase analysis. The diet was pelleted via steam conditioning (10 × 55 in Wenger twin staff pre-conditioner, Model 150) and using a pellet mill (CPM Model 1012-2) with a 3/16 × 1 1/4 in pellet die (L:D 6.7). Conditioner retention time was set at 30 sec and production rate was set at 33 lb/min, approximately 100% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. For each treatment, pellet and conditioned mash samples were composited such that 2 samples of each were analyzed for phytase activity and pellet durability index (PDI). Moisture analysis was conducted on initial mash, conditioned mash, hot pellet, and cooled pellet samples. Conditioning temperature, hot pellet temperature (HPT), and production rate were recorded throughout each processing run. Data were analyzed using the GLIMMIX procedure in SAS 9.4, with pelleting run as the experimental unit and day as the blocking factor. There was no evidence (P > 0.17) for a steam pressure × conditioning temperature interaction for HPT, phytase stability, moisture, or PDI. Increasing conditioning temperature from 170 to 190°F increased (linear, P < 0.01) HPT. There was no evidence for difference (P = 0.80) in HPT between steam pressures. Phytase stability of conditioned mash decreased (linear, P < 0.01) with increasing conditioning temperature. In cooled pellets, phytase stability decreased (linear, P < 0.01) with increasing conditioning temperature. Cooled pellets tended (P = 0.08) to have greater phytase stability when steam pressure was set at 44 psi compared to 24 psi. Moisture of conditioned mash and pellets increased (linear, P ≤ 0.05) with increasing conditioning temperature, and PDI tended (linear, P = 0.06) to increase with increasing conditioning temperature. There was no evidence (P > 0.35) that steam pressure affected feed moisture or PDI. Results of this experiment show that phytase stability in conditioned mash and pellets decreases linearly when the conditioning temperature rises above 170°F and HPT above 179°F. As expected, HPT increased and feed moisture tended to increase with increasing conditioning temperature. Increasing steam pressure from 24 to 44 psi resulted
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 28
Open AccessEffect of Steam Pressure and Conditioning Temperature During the Pelleting Process on Phytase Stability
This experiment was designed to evaluate the effects of steam pressure and conditioning temperature on the stability of microbial phytase. Treatments were arranged as a 2 × 3 factorial of steam pressure (24 and 44 psi) and conditioning temperature (170, 180, and 190°F). Phytase was added to a corn-soybean meal-based diet and mash samples were collected for phytase analysis. The diet was pelleted via steam conditioning (10 × 55 in Wenger twin staff pre-conditioner, Model 150) and using a pellet mill (CPM Model 1012-2) with a 3/16 × 1 1/4 in pellet die (L:D 6.7). Conditioner retention time was set at 30 sec and production rate was set at 33 lb/min, approximately 100% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. For each treatment, pellet and conditioned mash samples were composited such that 2 samples of each were analyzed for phytase activity and pellet durability index (PDI). Moisture analysis was conducted on initial mash, conditioned mash, hot pellet, and cooled pellet samples. Conditioning temperature, hot pellet temperature (HPT), and production rate were recorded throughout each processing run. Data were analyzed using the GLIMMIX procedure in SAS 9.4, with pelleting run as the experimental unit and day as the blocking factor. There was no evidence (P > 0.17) for a steam pressure × conditioning temperature interaction for HPT, phytase stability, moisture, or PDI. Increasing conditioning temperature from 170 to 190°F increased (linear, P < 0.01) HPT. There was no evidence for difference (P = 0.80) in HPT between steam pressures. Phytase stability of conditioned mash decreased (linear, P < 0.01) with increasing conditioning temperature. In cooled pellets, phytase stability decreased (linear, P < 0.01) with increasing conditioning temperature. Cooled pellets tended (P = 0.08) to have greater phytase stability when steam pressure was set at 44 psi compared to 24 psi. Moisture of conditioned mash and pellets increased (linear, P ≤ 0.05) with increasing conditioning temperature, and PDI tended (linear, P = 0.06) to increase with increasing conditioning temperature. There was no evidence (P > 0.35) that steam pressure affected feed moisture or PDI. Results of this experiment show that phytase stability in conditioned mash and pellets decreases linearly when the conditioning temperature rises above 170°F and HPT above 179°F. As expected, HPT increased and feed moisture tended to increase with increasing conditioning temperature. Increasing steam pressure from 24 to 44 psi resulted
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 29
Effect of Pellet Die Thickness and Conditioning Temperature During the Pelleting Process on Phytase Stability
This experiment was designed to evaluate the effects of pellet mill die thickness and conditioning temperature on the stability of microbial phytase. Treatments were arranged as a 2 × 3 factorial of die thickness (L:D 5.6 and 8.0) and conditioning temperature (165, 175, and 185°F). Phytase was added to a corn-soybean meal-based diet and mash samples were collected for phytase analysis. The diet was pelleted via steam conditioning (10 × 55 in Wenger twin staff pre-conditioner, Model 150) and using a pellet mill (CPM Model 1012-2) with a 5/32 × 7/8 in (L:D 5.6) or 5/32 × 1 1/4 in (L:D 8.0) pellet die. Conditioner retention time was set at 30 sec and production rate was set at 33 lb/min, approximately 100% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. Pellet and conditioned mash samples were collected and immediately placed in an experimental counter-flow cooler for 15 min. For each treatment, pellet and conditioned mash samples were composited such that 2 samples of each were analyzed for phytase activity and pellet durability index (PDI). Conditioning temperature, hot pellet temperature (HPT), and production rate were recorded throughout each processing run. Data were analyzed using the GLIMMIX procedure in SAS (v. 9.4), with pelleting run as the experimental unit and day as the blocking factor. There was no evidence (P > 0.14) for a die thickness × conditioning temperature inter- action for any of the pelleting or phytase responses analyzed in this study. Hot pellet temperature was increased when diets were pelleted with a thicker die (P < 0.01), and by increasing conditioning temperature from 165 to 185°F (linear, P < 0.01). Pellet durability index was greater (P < 0.01) for diets pelleted using the thicker die with an 8.0 L:D compared to the die with a 5.6 L:D. Additionally, PDI increased (linear, P = 0.03) with increasing conditioning temperature. Increasing conditioning temperature from 165 to 185°F decreased (linear, P < 0.01) phytase stability of conditioned mash and cooled pellets, with no difference (P > 0.72) in stability due to die thickness. Results of this experiment show that phytase stability in conditioned mash and pellets decreases linearly when conditioning temperature rises above 165°F and HPT rises above 177°F. Although the thicker pellet die increased HPT by an average of 1.9°F and increased PDI by an average of 7.8%, there was no evidence that the
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 29
Open AccessEffect of Pellet Die Thickness and Conditioning Temperature During the Pelleting Process on Phytase Stability
This experiment was designed to evaluate the effects of pellet mill die thickness and conditioning temperature on the stability of microbial phytase. Treatments were arranged as a 2 × 3 factorial of die thickness (L:D 5.6 and 8.0) and conditioning temperature (165, 175, and 185°F). Phytase was added to a corn-soybean meal-based diet and mash samples were collected for phytase analysis. The diet was pelleted via steam conditioning (10 × 55 in Wenger twin staff pre-conditioner, Model 150) and using a pellet mill (CPM Model 1012-2) with a 5/32 × 7/8 in (L:D 5.6) or 5/32 × 1 1/4 in (L:D 8.0) pellet die. Conditioner retention time was set at 30 sec and production rate was set at 33 lb/min, approximately 100% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. Pellet and conditioned mash samples were collected and immediately placed in an experimental counter-flow cooler for 15 min. For each treatment, pellet and conditioned mash samples were composited such that 2 samples of each were analyzed for phytase activity and pellet durability index (PDI). Conditioning temperature, hot pellet temperature (HPT), and production rate were recorded throughout each processing run. Data were analyzed using the GLIMMIX procedure in SAS (v. 9.4), with pelleting run as the experimental unit and day as the blocking factor. There was no evidence (P > 0.14) for a die thickness × conditioning temperature inter- action for any of the pelleting or phytase responses analyzed in this study. Hot pellet temperature was increased when diets were pelleted with a thicker die (P < 0.01), and by increasing conditioning temperature from 165 to 185°F (linear, P < 0.01). Pellet durability index was greater (P < 0.01) for diets pelleted using the thicker die with an 8.0 L:D compared to the die with a 5.6 L:D. Additionally, PDI increased (linear, P = 0.03) with increasing conditioning temperature. Increasing conditioning temperature from 165 to 185°F decreased (linear, P < 0.01) phytase stability of conditioned mash and cooled pellets, with no difference (P > 0.72) in stability due to die thickness. Results of this experiment show that phytase stability in conditioned mash and pellets decreases linearly when conditioning temperature rises above 165°F and HPT rises above 177°F. Although the thicker pellet die increased HPT by an average of 1.9°F and increased PDI by an average of 7.8%, there was no evidence that the
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 21
Pelleting and Starch Characteristics of Diets Containing High Amylase Corn
This experiment was designed to evaluate the effects of die thickness and conditioning temperature on pelleting and starch characteristics in diets containing either conventional yellow dent or high amylase corn (Enogen®, Syngenta Seeds, LLC). Treatments were arranged as a 2 × 2 × 3 factorial of corn type (conventional and high amylase), die thickness (L:D 5.6 and 8.0), and conditioning temperature (165, 175, and 185°F). For the high amylase corn treatments, ground high amylase corn replaced conventional ground corn on a lb:lb basis. Diets were pelleted via steam conditioning (10 in × 55 in Wenger twin staff pre-conditioner, Model 150) and using a pellet mill (CPM Model 1012-2) with a 5/32 in × 7/8 in (L:D 5.6) or 5/32 in × 1 1/4 in (L:D 8.0) pellet die. Conditioner retention time was set at 30 sec and production rate was set at 33 lb/min. All treatments were replicated on 3 separate days. Pellets were composited and analyzed for starch and pellet durability index (PDI). Conditioning temperature, hot pellet temperature (HPT), production rate, and pellet mill energy consumption were recorded throughout each processing run. Data were analyzed using the GLIMMIX procedure in SAS (v. 9.4, SAS Institute Inc., Cary, NC), with pelleting run as the experimental unit and day as the blocking factor. The 3-way interaction was not significant (P > 0.15) for any of the pelleting or starch responses analyzed in this study. There was no evidence (P > 0.14) for a corn type × conditioning temperature interaction for HPT, PDI, or energy consumption. There was a tendency (P = 0.08) for a corn type × die thickness interaction for PDI. The PDI for the high amylase and conventional corn treatments were similar when diets were pelleted using the L:D 8.0 die. However, PDI for conventional corn diets was greater than high amylase corn diets when pelleted using the L:D 5.6 die. Pelleting diets with the L:D 8.0 die had improved (P < 0.01) PDI compared to the L:D 5.6. Additionally, PDI increased (linear, P = 0.03) with increasing conditioning temperature. Pellet mill energy consumption was greater for the thicker pellet die (P = 0.02), and tended to decrease (quadratic, P = 0.07) with increasing conditioning temperature. There was a corn type × conditioning temperature interaction (P = 0.01) for gelatinized starch in conditioned mash. High amylase corn diets steam conditioned at 185°F had greater gelatinized starch than all other
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 21
Open AccessPelleting and Starch Characteristics of Diets Containing High Amylase Corn
This experiment was designed to evaluate the effects of die thickness and conditioning temperature on pelleting and starch characteristics in diets containing either conventional yellow dent or high amylase corn (Enogen®, Syngenta Seeds, LLC). Treatments were arranged as a 2 × 2 × 3 factorial of corn type (conventional and high amylase), die thickness (L:D 5.6 and 8.0), and conditioning temperature (165, 175, and 185°F). For the high amylase corn treatments, ground high amylase corn replaced conventional ground corn on a lb:lb basis. Diets were pelleted via steam conditioning (10 in × 55 in Wenger twin staff pre-conditioner, Model 150) and using a pellet mill (CPM Model 1012-2) with a 5/32 in × 7/8 in (L:D 5.6) or 5/32 in × 1 1/4 in (L:D 8.0) pellet die. Conditioner retention time was set at 30 sec and production rate was set at 33 lb/min. All treatments were replicated on 3 separate days. Pellets were composited and analyzed for starch and pellet durability index (PDI). Conditioning temperature, hot pellet temperature (HPT), production rate, and pellet mill energy consumption were recorded throughout each processing run. Data were analyzed using the GLIMMIX procedure in SAS (v. 9.4, SAS Institute Inc., Cary, NC), with pelleting run as the experimental unit and day as the blocking factor. The 3-way interaction was not significant (P > 0.15) for any of the pelleting or starch responses analyzed in this study. There was no evidence (P > 0.14) for a corn type × conditioning temperature interaction for HPT, PDI, or energy consumption. There was a tendency (P = 0.08) for a corn type × die thickness interaction for PDI. The PDI for the high amylase and conventional corn treatments were similar when diets were pelleted using the L:D 8.0 die. However, PDI for conventional corn diets was greater than high amylase corn diets when pelleted using the L:D 5.6 die. Pelleting diets with the L:D 8.0 die had improved (P < 0.01) PDI compared to the L:D 5.6. Additionally, PDI increased (linear, P = 0.03) with increasing conditioning temperature. Pellet mill energy consumption was greater for the thicker pellet die (P = 0.02), and tended to decrease (quadratic, P = 0.07) with increasing conditioning temperature. There was a corn type × conditioning temperature interaction (P = 0.01) for gelatinized starch in conditioned mash. High amylase corn diets steam conditioned at 185°F had greater gelatinized starch than all other
- Open Access
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 15
Stability of Four Commercial Microbial Phytase Sources Under Increasing Conditioning Temperatures and Conditioner Retention Times During Pelleting
This experiment was designed to evaluate the effects of conditioning temperature and retention time on the stability of 4 commercially available microbial phytases in a corn soybean meal diet. Treatments were arranged in a 4 × 3 × 2 factorial of phytase source (A, B, C, and D), conditioning temperature (180, 190, and 200°F), and conditioner retention time (30 and 60 s). Diets were formulated to release 0.15% phosphorus. A total of 5 mash samples from each treatment were analyzed for phytase. Diets were pelleted via steam conditioning (10 × 55 in. Wenger twin staff pre-conditioner, Model 150) using a 30-horsepower pellet mill (1012-2 HD Master Model, California Pellet Mill) with a 3/16 × 2 in. pellet die. Production rate was set at 10 lb/min, approximately 30% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. Retention time was randomized within day and phytase sources were randomized within retention time. Pellets were collected after the die and cooled for 10 min. Five cooled pellet samples per treatment per day were analyzed for phytase. Data were analyzed using the GLIMMIX procedure in SAS 9.4, with pelleting run as the experimental unit and day as the blocking factor. There was no evidence for a source × conditioning temperature × retention time interaction for hot pellet temperature or phytase stability. Increasing conditioning temperature (180, 190, and 200°F) increased (quadratic, P < 0.03) hot pellet temperature (203, 208, and 211°F, respectively). There was no evidence of difference in hot pellet temperature due to retention time. There was a phytase source × conditioning temperature interaction (P = 0.01) for phytase stability. At conditioning temperatures of 180, 190, and 200°F, phytase stabilities were 33.7, 17.5, and 16.3% for A; 13.0, 8.3, and 9.0% for B; 24.2, 11.2, and 11.8% for C; and 20.7, 11.5, and 9.7% for D; respectively. At conditioning temperatures of 180 and 190°F, phytase A had greater (P < 0.05) stability compared to all other sources. At 200°F, there was no evidence of difference between phytase A and C stability, but stability of phytase A was greater (P < 0.05) than phytase B and D. Phytase stability of B was less (P < 0.05) than that of the other sources when pelleted at 180°F. When pelleted at a conditioning temperature of 200°F, phytase stability was similar between phytase B, C, and D. There was no evidence
- 1 January 2018
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 4 (9) , 15
Open AccessStability of Four Commercial Microbial Phytase Sources Under Increasing Conditioning Temperatures and Conditioner Retention Times During Pelleting
This experiment was designed to evaluate the effects of conditioning temperature and retention time on the stability of 4 commercially available microbial phytases in a corn soybean meal diet. Treatments were arranged in a 4 × 3 × 2 factorial of phytase source (A, B, C, and D), conditioning temperature (180, 190, and 200°F), and conditioner retention time (30 and 60 s). Diets were formulated to release 0.15% phosphorus. A total of 5 mash samples from each treatment were analyzed for phytase. Diets were pelleted via steam conditioning (10 × 55 in. Wenger twin staff pre-conditioner, Model 150) using a 30-horsepower pellet mill (1012-2 HD Master Model, California Pellet Mill) with a 3/16 × 2 in. pellet die. Production rate was set at 10 lb/min, approximately 30% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. Retention time was randomized within day and phytase sources were randomized within retention time. Pellets were collected after the die and cooled for 10 min. Five cooled pellet samples per treatment per day were analyzed for phytase. Data were analyzed using the GLIMMIX procedure in SAS 9.4, with pelleting run as the experimental unit and day as the blocking factor. There was no evidence for a source × conditioning temperature × retention time interaction for hot pellet temperature or phytase stability. Increasing conditioning temperature (180, 190, and 200°F) increased (quadratic, P < 0.03) hot pellet temperature (203, 208, and 211°F, respectively). There was no evidence of difference in hot pellet temperature due to retention time. There was a phytase source × conditioning temperature interaction (P = 0.01) for phytase stability. At conditioning temperatures of 180, 190, and 200°F, phytase stabilities were 33.7, 17.5, and 16.3% for A; 13.0, 8.3, and 9.0% for B; 24.2, 11.2, and 11.8% for C; and 20.7, 11.5, and 9.7% for D; respectively. At conditioning temperatures of 180 and 190°F, phytase A had greater (P < 0.05) stability compared to all other sources. At 200°F, there was no evidence of difference between phytase A and C stability, but stability of phytase A was greater (P < 0.05) than phytase B and D. Phytase stability of B was less (P < 0.05) than that of the other sources when pelleted at 180°F. When pelleted at a conditioning temperature of 200°F, phytase stability was similar between phytase B, C, and D. There was no evidence