AYA. Yoder

A. Yoder

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


A. Yoder has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Mill Type and Particle Size Variation on Growth Performance and Carcass Characteristics of Finishing Pigs

    by M. B. Braun, H. K. Wecker, A. Yoder, J. C. Woodworth, C. R. Stark, C. B. Paulk

    The objective of this experiment was to determine the effects of mill type used to grind corn and its particle size variation on diet flowability and subsequent finishing pig growth performance and carcass characteristics. A total of 200 pigs (DNA Line 241 × 600; initially 121.9 lb) were used in a 75-d growth trial. Pigs were randomly assigned to pens with either 5 barrows or 5 gilts per pen. Pens were then randomly allotted to 1 of 4 treatments balanced by weight and gender with 10 pens per treatment. Treatments were arranged as a 2 × 2 factorial with 2 mill types (3-high roller mill; RMS, Model 924 or a hammermill; Bliss, model 22115) and 2 particle size variations (standard vs. blended). Increasing corn particle size variation was accomplished by blending 30% 400 μm corn, 40% 600 μm corn, and 30% 800 μm corn. Standard treatments were accomplished by grinding corn to an average of 600 μm with either mill. On d 75, pigs were transported to a commercial packing plant for processing and determination of carcass characteristics. The average analyzed complete diet mean particle sizes and standard deviations were 497, 540, 503, and 520 μm and 2.70, 2.75. 3.35, and 3.35 for the roller mill standard, roller mill blended, hammermill standard, and hammermill blended treatments, respectively. Diet flowability was calculated using angle of repose (AoR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). The AOR were 34.2, 33.0, 35.4, and 36.2º; COD were 32.0, 31.3, 30.0, and 33.0 mm; compressibilitys were 18.7, 18.4, 17.0, and 15.7%; and CFI were 52.9, 55.4, 53.9, and 53.2 for the roller mill standard, roller mill blended, hammermill standard, and hammermill blended treatments, respectively. There were no interactions or main effects of mill type on growth performance or carcass characteristics. However, pigs fed the blended diets had marginally significant decreased (P < 0.083) average daily gain (ADG) compared to those fed the standard diets. No differences were observed in total feed cost or cost per lb of gain between treatments. Pigs fed blended diets also had marginally decreased (P < 0.059) gain value and income over feed costs (IOFC) compared to those fed diets that were not blended. In conclusion, mill type used to grind corn and increasing particle size variation did not impact flowability metrics of complete diets. Mill type used to grind corn did not

  • Open Access

    Evaluation of Pellet Binders on Pellet Durability Index of a High-Fat Swine Diet

    by H. K. Wecker, C. E. Evans, A. Yoder, M. Saensukjaroenphon, C. R. Stark, K. A. Barry, C. B. Paulk

    The objective of this study was to evaluate the addition of different pellet binders on pellet quality of a grower swine diet by measuring pellet durability index (PDI). Dietary treatments consisted of a corn-soybean meal-based control diet with 20% dried distillers grains with solubles and 4% choice white grease, the control diet with 0.6% lignosulfonate (AMERI-BOND 2X; LignoTech USA Inc.; Rothschild, WI), or the control diet with increasing levels of a pasta by-product (2.5, 5.0, or 10.0%; International Ingredients, St. Louis, MO). Pellet binders were added to the control diet in the place of corn to create dietary treatments. Each treatment was pelleted in 333 lb batches at 3 separate periods to provide 3 replications per treatment. Pelleting run was considered the experimental unit and time of processing served as the blocking factor. Order of pelleting dietary treatments was randomized within each time period. Corn was ground to approximately 600 μm. Diets were pelleted via steam conditioning (10- × 55-in. Wenger twin staff conditioner, Model 150) and using a 30-horsepower pellet mill (1012-2 HD Master Model, California Pellet Mill) with a 5/32- × 1-in. pellet die. During each processing run, pellet samples were collected throughout the run and immediately placed in an experimental counter-flow cooler for 10 minutes. After cooling, samples were analyzed for pellet durability index using the Holmen NHP 100 (TekPro Ltd, Norfolk, UK) for 30 seconds. There was no evidence (P > 0.172) of difference for the effect of treatment on conditioner temperature, hot pellet temperature, or production rate. The average conditioner temperature, hot pellet temperature, and production rate were 185.9°F, 188.2°F, and 1,364 lb/h, respectively. The diet containing lignosulfate improved (P < 0.001) PDI compared to the control diet. Increasing pasta by-product from 2.5 to 10% increased the PDI (P < 0.01) compared with the control diet. Diets containing 2.5% pasta by-product had lower PDI compared to those with lignosulfonate, diets with 5% pasta by-product and lignosulfonate had similar PDI, and diets containing 10% pasta by-product had increased PDI compared to the lignosulfonate treatment. In conclusion, adding pellet binders to the high fat finisher diets improved PDI by 7.4 to 10.7%. Adding 5% pasta by-product improved PDI similar to that of lignosulfonate and adding 10% pasta by-product further improved PDI compared to lignosulfonate.


  • Open Access

    Stability of Four Commercial Microbial Phytase Sources Under Increasing Conditioning Temperatures and Conditioner Retention Times During Pelleting

    by C. N. Truelock, A. D. Yoder, C. E. Evans, C. R. Stark, S. S. Dritz, J. W. Wilson, N. E. Ward, C. B. Paulk

    This experiment was designed to evaluate the effects of conditioning temperature and retention time on the stability of 4 commercially available microbial phytases in a corn soybean meal diet. Treatments were arranged in a 4 × 3 × 2 factorial of phytase source (A, B, C, and D), conditioning temperature (180, 190, and 200°F), and conditioner retention time (30 and 60 s). Diets were formulated to release 0.15% phosphorus. A total of 5 mash samples from each treatment were analyzed for phytase. Diets were pelleted via steam conditioning (10 × 55 in. Wenger twin staff pre-conditioner, Model 150) using a 30-horsepower pellet mill (1012-2 HD Master Model, California Pellet Mill) with a 3/16 × 2 in. pellet die. Production rate was set at 10 lb/min, approximately 30% of the rated throughput for the pellet mill. All treatments were replicated on 3 separate days. Retention time was randomized within day and phytase sources were randomized within retention time. Pellets were collected after the die and cooled for 10 min. Five cooled pellet samples per treatment per day were analyzed for phytase. Data were analyzed using the GLIMMIX procedure in SAS 9.4, with pelleting run as the experimental unit and day as the blocking factor. There was no evidence for a source × conditioning temperature × retention time interaction for hot pellet temperature or phytase stability. Increasing conditioning temperature (180, 190, and 200°F) increased (quadratic, P < 0.03) hot pellet temperature (203, 208, and 211°F, respectively). There was no evidence of difference in hot pellet temperature due to retention time. There was a phytase source × conditioning temperature interaction (P = 0.01) for phytase stability. At conditioning temperatures of 180, 190, and 200°F, phytase stabilities were 33.7, 17.5, and 16.3% for A; 13.0, 8.3, and 9.0% for B; 24.2, 11.2, and 11.8% for C; and 20.7, 11.5, and 9.7% for D; respectively. At conditioning temperatures of 180 and 190°F, phytase A had greater (P < 0.05) stability compared to all other sources. At 200°F, there was no evidence of difference between phytase A and C stability, but stability of phytase A was greater (P < 0.05) than phytase B and D. Phytase stability of B was less (P < 0.05) than that of the other sources when pelleted at 180°F. When pelleted at a conditioning temperature of 200°F, phytase stability was similar between phytase B, C, and D. There was no evidence