Tongquan Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tongquan Wang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Huantong Shi
Xi’an Jiaotong University
4 shared publications - Jian Wu
Xi’an Jiaotong University
4 shared publications - Peizhou Zhang
State Key Laboratory of Electical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an 710049, People’s Republic of China
4 shared publications - Xingwen Li
Xi’an Jiaotong University
4 shared publications - Dongsheng Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University , Xi'an 710049
3 shared publications - Ming Xu
State Key Laboratory of Electical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an 710049, People’s Republic of China
3 shared publications
Latest Publications
- 5 March 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (9) , 095204
Bench-scale single-pulse x-ray diffraction based on a wire-shorted rod-pinch diode
The flash x-ray source generated by a wire-shorted rod-pinch diode (WS-RPD) is characterized as a potential source for transient single-pulse x-ray diffraction (XRD) in dynamic experiments. Driven by a bench-scale pulsed power device, the WS-RPD generates intense x-rays with a ∼30 ns pulse width (full width at half maximum), and the probing energy can be conveniently adjusted by changing the anode material without modifying the load geometry or driving parameters. For copper and molybdenum anodes, the yield of K α photons exceeds 10 13 per shot in 4π sr. A polycapillary optic is adopted to further increase the probing photons and suppress the bremsstrahlung background, resulting in ∼10 8 probing photons impinging on a sample located 340 mm from the source and a signal-to-background ratio greater than ten (with a copper anode). The number of probing photons is much higher than the number reported for single-pulse XRD sources based on pulsed discharge, such as the x-pinch and vacuum-gap RPDs, and is comparable to an x-ray source produced by the interaction between a petawatt laser and a target.
- 5 March 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (9) , 095204
Bench-scale single-pulse x-ray diffraction based on a wire-shorted rod-pinch diode
The flash x-ray source generated by a wire-shorted rod-pinch diode (WS-RPD) is characterized as a potential source for transient single-pulse x-ray diffraction (XRD) in dynamic experiments. Driven by a bench-scale pulsed power device, the WS-RPD generates intense x-rays with a ∼30 ns pulse width (full width at half maximum), and the probing energy can be conveniently adjusted by changing the anode material without modifying the load geometry or driving parameters. For copper and molybdenum anodes, the yield of K α photons exceeds 10 13 per shot in 4π sr. A polycapillary optic is adopted to further increase the probing photons and suppress the bremsstrahlung background, resulting in ∼10 8 probing photons impinging on a sample located 340 mm from the source and a signal-to-background ratio greater than ten (with a copper anode). The number of probing photons is much higher than the number reported for single-pulse XRD sources based on pulsed discharge, such as the x-pinch and vacuum-gap RPDs, and is comparable to an x-ray source produced by the interaction between a petawatt laser and a target.
- Open Access
- 1 January 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (1)
Plasma dynamics of a wire-shorted rod-pinch diode for flash x-ray radiography
The rod-pinch diode (RPD) is one of the most iconic load configurations for flash x-ray radiography, which offers advantages of simple structure and high-quality x-ray spot. While physical models have been well-developed for the classic vacuum RPD since the 1970s, research remains lacking for its low-impedance variant using a metal wire to pre-short the anode–cathode gap, particularly on the plasma dynamics following electrical wire explosion (EWE) in the diode. The wire-shorted RPD features an operating impedance of <1 Ω, which is desirable on a high-current low-impedance pulse driver for high x-ray dose conversion. This work investigates the joint phenomenology from the plasma diagnostics, electrical measurements, and radiation detections of a wire-shorted RPD, offering a novel perspective on its plasma behaviors. Results from both experiment and magneto-hydrodynamic simulation show that the wire trailing mass persists throughout the x-ray emission phase, with only fractional mass adjacent to the anode pushed toward the rod tip. Unlike the micro diode at rod tip in a plasma-prefilled RPD, the much denser EWE plasma in a wire-shorted RPD forms an extended current return path prior to x-ray burst, and the electrons pinched at the rod tip are emitted from a large cathode area.
- 1 January 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (1)
Open AccessPlasma dynamics of a wire-shorted rod-pinch diode for flash x-ray radiography
The rod-pinch diode (RPD) is one of the most iconic load configurations for flash x-ray radiography, which offers advantages of simple structure and high-quality x-ray spot. While physical models have been well-developed for the classic vacuum RPD since the 1970s, research remains lacking for its low-impedance variant using a metal wire to pre-short the anode–cathode gap, particularly on the plasma dynamics following electrical wire explosion (EWE) in the diode. The wire-shorted RPD features an operating impedance of <1 Ω, which is desirable on a high-current low-impedance pulse driver for high x-ray dose conversion. This work investigates the joint phenomenology from the plasma diagnostics, electrical measurements, and radiation detections of a wire-shorted RPD, offering a novel perspective on its plasma behaviors. Results from both experiment and magneto-hydrodynamic simulation show that the wire trailing mass persists throughout the x-ray emission phase, with only fractional mass adjacent to the anode pushed toward the rod tip. Unlike the micro diode at rod tip in a plasma-prefilled RPD, the much denser EWE plasma in a wire-shorted RPD forms an extended current return path prior to x-ray burst, and the electrons pinched at the rod tip are emitted from a large cathode area.
- 11 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (20)
Enhanced tungsten wire energy deposition during copper–tungsten intertwined electrical explosion in atmospheric air
Intertwined electrical wire explosion (EWE) is considered as a potential method for large-scale synthesis of high-entropy alloy nanoparticles, while the helical structure, close contact, and different electrothermal properties of wires add to the difficulties of controlling the Joule energy distribution among the wires. In this paper, two very dissimilar materials, copper and tungsten, are chosen as representatives of nonrefractory and refractory metals, and the Cu–W intertwined EWE is compared to parallel EWE of spaced straight Cu and W wires. It is found that for the intertwined load, the majority of the tungsten wire is located in the center and encapsulated by copper vapor, with a low-density spiral plasma belt surrounding the exploding product, and the tungsten wire is transformed into a highly vaporized state instead of a typical core–corona structure, with expansion velocity ∼1.8 times and average energy deposition more than three times that of the parallel load. This dramatic difference is attributed to the high-density and high-pressure vapor medium created by early explosion of the copper wire, which surrounds the tungsten wire and suppresses the formation and expansion of conductive surface plasma channel. These findings can serve to improve the load design for achieving simultaneous dispersion and uniform mixing of dissimilar materials via intertwined EWE.
- 11 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (20)
Enhanced tungsten wire energy deposition during copper–tungsten intertwined electrical explosion in atmospheric air
Intertwined electrical wire explosion (EWE) is considered as a potential method for large-scale synthesis of high-entropy alloy nanoparticles, while the helical structure, close contact, and different electrothermal properties of wires add to the difficulties of controlling the Joule energy distribution among the wires. In this paper, two very dissimilar materials, copper and tungsten, are chosen as representatives of nonrefractory and refractory metals, and the Cu–W intertwined EWE is compared to parallel EWE of spaced straight Cu and W wires. It is found that for the intertwined load, the majority of the tungsten wire is located in the center and encapsulated by copper vapor, with a low-density spiral plasma belt surrounding the exploding product, and the tungsten wire is transformed into a highly vaporized state instead of a typical core–corona structure, with expansion velocity ∼1.8 times and average energy deposition more than three times that of the parallel load. This dramatic difference is attributed to the high-density and high-pressure vapor medium created by early explosion of the copper wire, which surrounds the tungsten wire and suppresses the formation and expansion of conductive surface plasma channel. These findings can serve to improve the load design for achieving simultaneous dispersion and uniform mixing of dissimilar materials via intertwined EWE.
- 1 July 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (7)
Compact hard x-ray flash radiography device based on wire-shorted low-impedance rod pinch diode
A rod pinch diode (RPD) is a feasible load configuration to generate a high-brightness, small-size hard x-ray radiation source. In this paper, the radiography performance of a wire-shorted low-impedance RPD on a compactly designed table-top driver (WRPD-1) is demonstrated for the first time. The driver consists of four high-power discharge branches connected in parallel, with each branch consisting of two metal-film capacitors and one multigap field-distortion switch in series. The four branches are triggered synchronously to generate a fast-rising current pulse: the inductance of the load section at the short circuit is ∼10 nH, and the short-circuit current amplitude is ∼325 kA at ±90 kV charging voltage, with a 10%–90% rise time of 110 ns. With a low-impedance RPD shorted by an 18-µm-diameter aluminum wire, a quasi-spherical x-ray focal spot with diameter 10 keV reaches ∼1.16 J. The present results show that the device can serve well for the flash radiography diagnosis and potentially as an efficient light source for dynamic x-ray diffraction.
- 1 July 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (7)
Compact hard x-ray flash radiography device based on wire-shorted low-impedance rod pinch diode
A rod pinch diode (RPD) is a feasible load configuration to generate a high-brightness, small-size hard x-ray radiation source. In this paper, the radiography performance of a wire-shorted low-impedance RPD on a compactly designed table-top driver (WRPD-1) is demonstrated for the first time. The driver consists of four high-power discharge branches connected in parallel, with each branch consisting of two metal-film capacitors and one multigap field-distortion switch in series. The four branches are triggered synchronously to generate a fast-rising current pulse: the inductance of the load section at the short circuit is ∼10 nH, and the short-circuit current amplitude is ∼325 kA at ±90 kV charging voltage, with a 10%–90% rise time of 110 ns. With a low-impedance RPD shorted by an 18-µm-diameter aluminum wire, a quasi-spherical x-ray focal spot with diameter 10 keV reaches ∼1.16 J. The present results show that the device can serve well for the flash radiography diagnosis and potentially as an efficient light source for dynamic x-ray diffraction.