GKGulnara Letayevna Katkeeva

Gulnara Letayevna Katkeeva

*This is an algorithmically generated author record based on publicly available information.

Gulnara Letayevna Katkeeva has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Recovery of Manganese from Manganese Ore Processing Tailings by High-Intensity Magnetic Separation

    by Aidarkhan Mukhtar, Gulnara Katkeeva, Ardak Makashev, Muratkhan Atakhan, Serik Gabdullin, Alexey Orlov, Bayan Kassymova, Zhaslan Dyusekeyev, Alexander Kurkin, Serik Nazymbekov

    The increasing volumes of mining and mineral processing tailings and the declining quality of natural manganese ores have intensified interest in the recovery of valuable components from previously accumulated processing wastes. In this study, the efficiency of dry high-intensity magnetic separation for manganese concentration from manganese ore processing tailings generated during the processing of manganese ores in the Ulytau Region of the Republic of Kazakhstan was investigated. According to chemical analysis, the initial sample contained 9.81% Mn, 3.01% Fe, and 60.57% SiO2. A representative sample was characterized using X-ray diffraction (XRD), scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS), and atomic absorption spectrometry (AAS). Dry magnetic separation tests were performed using a PC-B 12/10-12.018–2012 belt magnetic separator at magnetic field intensities ranging from 0.33 to 0.90 T. It was established that manganese in the initial material was predominantly associated with weakly magnetic minerals, which accounts for the effectiveness of high-intensity magnetic separation. As a result, a magnetic concentrate was obtained with a yield of 27.60%, a Mn content of 25.89%, and a Mn recovery of 72.84%. According to the chemical analysis, the manganese content increased from 9.81% in the initial material to 25.89% in the magnetic product, corresponding to an enrichment ratio of approximately 2.64. At the same time, the SiO2 content decreased from 60.57% to 34.02%, indicating effective separation of the silicate gangue. The results confirm the potential of dry high-intensity magnetic separation for processing manganese ore processing tailings and producing a marketable concentrate with minimal water consumption.

  • Open Access

    Electrochemical Pretreatment of Chrysocolla for Enhanced Sulfidization and Flotation: Mechanism and Process Optimization

    by Gulnara Katkeeva, Zhamila Shaike, Aidarkhan Mukhtar, Karakat Turebekova, Gulmarzhan Burkitseterkyzy, Yerlan Zhunussov, Anuar Zhunussov, Sultan Kabylkanov

    The flotation of oxidized copper minerals is limited by poor surface reactivity and the insufficient effectiveness of conventional sulfidization. This study investigated 50 Hz alternating current electrochemical pretreatment to enhance the sulfidization and flotation of chrysocolla and a natural oxidized copper ore. Operating parameters, including current density, treatment time, pulp pH, and sodium sulfide dosage, were optimized using a design of experiments approach. Phase transformations were characterized by scanning electron microscopy with energy-dispersive X-ray spectroscopy and X-ray diffraction. Pretreatment with 50 Hz alternating current promoted the surface formation of tenorite (CuO), which was subsequently transformed into covellite (CuS) during sulfidization, providing favorable conditions for subsequent flotation. The optimum conditions for chrysocolla were a current density of 100 A m−2, a pretreatment time of 0.5 min, pH 8, a sodium sulfide dosage of 25% of the stoichiometric requirement, and a sulfidization time of 2.5 min. Validation tests on natural oxidized copper ore showed that alternating current pretreatment increased copper recovery from 29.16% to 79.63% and concentrate grade from 12.84 to 25.50 wt.% compared with conventional sulfidization. These findings demonstrate that alternating current electrochemical pretreatment effectively modifies oxidized copper mineral surfaces and enhances their subsequent sulfidization and flotation, providing a promising approach for the beneficiation of refractory oxidized copper ores.

  • Open Access

    Structural and Functional Properties of the Oxide System LaCaCuVMnO7.5 and Its Composites with YBa2Cu3Ox

    by Zhenisgul Imangalievna Sagintaeva, Shuga Bulatovna Kasenova, Bulat Kunurovich Kasenov, Erbolat Ermekovich Kuanyshbekov, Aigul Tanirbergenovna Ordabaeva, Zamira Berikbaykyzy Sarsenbayeva, Gulnara Letayevna Katkeeva

    Oxide systems with the nominal composition LaCaCuVMnO7.5 and composites modified with the YBa2Cu3Ox phase were synthesized by the solid-state reaction method. The phase composition and structural features were systematically investigated by X-ray diffraction (XRD), Rietveld refinement, and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM–EDX). The parent oxide was found to form a two-phase system, consisting of an orthorhombic perovskite-like phase and a cubic manganite–vanadate phase, whereas the introduction of 10 wt.% YBa2Cu3Ox resulted in the formation of a three-phase composite containing an additional cuprate phase. Thermophysical investigations in the 298–673 K range revealed λ-type-like anomalies in the heat capacity, which may be associated with possible structural or interphase transformations in the investigated oxide systems. The incorporation of YBa2Cu3Ox significantly modified the temperature dependence of heat capacity and increased its values over both low- and high-temperature regions. Electrophysical measurements in the 293–483 K range confirmed the semiconducting nature of conductivity, while the addition of YBa2Cu3Ox reduced electrical resistance and enhanced dielectric permittivity. These findings demonstrate that YBa2Cu3Ox modification provides an effective route for tuning the thermophysical and electrophysical properties of LaCaCuVMnO7.5-based oxide systems, suggesting their potential as promising candidates for multifunctional oxide materials with possible electronic and sensor-related applications.

  • Open Access

    Recovery Potential of Critical Rare Earth Elements from Coal Preparation Tailings: A Case Study of the Abayskaya Mine

    by Gulnara Katkeeva, Ilyas Oskembekov, Yerlan Zhunussov, Zhamila Shaike, Baurzhan Kozhabekov, Dilara Gizatullina, Karakat Turebekova, Sultan Kabylkanov

    Coal preparation tailings from the K18 seam of the Abayskaya mine were evaluated as a potential secondary source of critical rare earth elements (REEs). The study showed that REEs are predominantly associated with the mineral fraction of coal; therefore, during beneficiation, approximately 70% of their total content is transferred to flotation tailings. The concentrations of valuable elements in the tailings are as follows (g/t): Li—65; Sc—16; Y—17; Yb—2.5; V—135; and Ti—2293. These values significantly exceed the Clarke values and are comparable to those of some low-grade primary ores, indicating the potential of coal preparation wastes as a technogenic raw material for critical elements. To extract REEs from the resistant aluminosilicate matrix, a fluorine–ammonium sulfate thermochemical activation method was proposed. Using a probabilistic–deterministic experimental design approach, a mathematical model of the process was developed and optimal parameters were determined (400 °C, 120 min, (NH4)2SO4 consumption—140% relative to Al, NH4HF2 consumption—110% relative to Si), providing a feed liberation degree (by Al extraction) of up to 94%. Under optimal conditions, high leaching efficiencies of key elements were achieved: Sc (95%), Y (100%), Yb (100%), and Li (100%). The results demonstrate the significant potential of coal preparation tailings as a secondary resource of rare earth elements and confirm the efficiency of fluorine–ammonium sulfate technology for processing this type of technogenic waste.


  • Application of a multi-Functional reagent in the flotation process enrichment of oxidized copper ores

    by Katkeeva Gulnara Letaevna, Oskembekov Ilyas Malikovich, Akubaeva Makijan Aubakirovna, Gizatullina Dilara Rafailovna, Shaike Zhamila Armanovna, Zhunussov Yerlan Makhsutzhanovich, Zhunussov Anuarbek Makhsutzhanovich


  • Improving zinc flotation performance when processing lead-zinc ores

    by N. K. Omarova, R. T. Sherembaeva, G. L. Katkeeva, A. A. Mukhtar

    This paper studies sulfide lead-zinc ores of the Akzhal deposit in the Republic of Kazakhstan. The ore mineralization is relatively evenly distributed and is represented by pyrite, sphalerite, and galena. Flotation experiments were carried out in open and closed cycles under the current reagent conditions applied at the plant and under the reagent conditions proposed, using a silica depressant. The optimal grinding size was established at 69.77 % –0.074 mm, as it ensures the most acceptable process indicators, in particular, the zinc content in the zinc concentrate. Open-cycle experiments were carried out with the liquid glass rates varying between 60 and 120 g/t. At a rate of 60 g/t, the mass fraction of zinc in the concentrate was 23.03 % with a recovery of 52.29 %, and the mass fraction of silicon dioxide was 3.14 %. With a liquid glass consumption rate of 90 g/t, the mass fraction of zinc increased to 26.54 %, with a recovery of 54.41 %, and the mass fraction of silicon dioxide was 2.16 %. These are the maximum values of zinc content in the zinc concentrate achieved; with the liquid glass consumption rate increased to 120 g/t, the mass fraction of Zn in the concentrate dropped to 21.94 % with a recovery of 52.28 %, and the mass fraction of silicon dioxide was 3.15 %. In closed-cycle experiments, the mass fraction of zinc in the zinc concentrate was 43.99 % with a recovery of 58.47 %. The mass fraction of silicon dioxide in the concentrate was 2.15 %, with a recovery into the tailings of 94.03 %.


  • Барит шикізатының ашылуына бірігу жағдайларының әсерін зерттеу

    by K.S. Turebekova, G.L. Katkeeva, R.B. Sultangaziev, I.M. Oskembekov

    The object of works has been the barite-bearing technogenic wastes. These wastes have been not recycled yet. A promising solution to the issue is to explore the raw materials with the chemical methods, in particular, by a method of ammonium fluorosulfate desiliconization. The partial dependences of the raw material exploration on temperature, sintering time and consumption of the exploring reagents have been obtained. Based on the partial dependencies, a mathematical model of the sintering as a generalized multifactor equation has been created. This equation has determined the optimal conditions to explore the barite raw materials. A scheme of ammonium fluorinesulfate exploration of the barite raw materials has been developed Жұмыс объектісі – Қарағайлы кен байыту фабрикасының құрамында барит бар техногендік қалдықтар. Минералогиялық құрамы күрделі болғандықтан құрамында барит бар қалдықтарды өңдеу мәселесі күрделі болып табылады. Мәселені шешудің перспективалы жолы – шикізатты химиялық әдістермен ашу. Ашудың математикалық моделін құру және процестің оңтайлы шарттарын анықтау мақсатында фторидпен және аммо- ний сульфатымен біріктіру арқылы барит шикізатын ашу бойынша зерттеулер жүргізілді. Шикізатты ашудың температураға, біріктіру уақытына және ашу реагенттерінің шығынына ерекше тәуелділіктері алынған. Жартылай тәуелділіктер негізінде жалпыланған көпфакторлы теңдеу түріндегі біріктіру процесінің математикалық моделі алынды, оған сәйкес барит шикізатын ашудың оңтайлы шарттары анықталды. Барит шикізатын фторсульфат аммонийді ашу схемасы әзірленді Объектом работ являются баритсодержащие техногенные отходы Карагайлинской обогатительной фабрики. Проблема переработки баритсодержащих отходов состоит в сложном минералогическом составе. Перспективным решением проблемы является вскрытие сырья химическими методами. Проведены исследования вскрытия баритового сырья спеканием с фторидом и сульфатом аммония с целью построения математической модели вскрытия и определения оптимальных условий проведения процесса. Получены частные зависимости вскрытия сырья от температуры, времени спекания и расхода вскрывающих реагентов. На основании частных зависимостей получена математическая модель процесса спекания в виде обоб- щенного многофакторного уравнения, по которому определены оптимальные условия вскрытия баритового сырья. Разработана схема фторо-сульфато- аммонийного вскрытия баритового сырья

  • Collective flotation of desircified technogenic barite raw material

    by К.с. Туребекова, Г.л. Каткеева, И.м. Оскембеков, Р.б. Султангазиев

    В работе представлены результаты коллективной флотации обескремненного техногенного баритового сырья. Для определения эффективности применения флотационного метода обогащения без предварительного обескремнивания были проведены исследования по влиянию на извлечение цветных металлов из обескремненного баритового продукта во флотационный концентрат трех факторов – расходов активатора и собирателя, времени агитации пульпы с медным купоросом. В результате были определены оптимальные расходы реагентов и математическая модель процесса коллективной флотации обескремненного баритового продукта. Получены удовлетворительные результаты по извлечению в коллективный концентрат меди, цинка и свинца. Коллективная флотация обескремненного баритового продукта при оптимальных условиях показала, что цветные металлы извлекаются при оптимальных условиях на уровне 98%. The paper presents the results of collective flotation of desiliconized technogenic barite raw materials. To determine the effectiveness of the use of the flotation method of enrichment without prior desiliconization, studies were carried out on the effect on the extraction of non-ferrous metals from the desiliconized barite product into the flotation concentrate of three factors – the costs of the activator and collector, the time of pulp agitation with copper sulphate. As a result, the optimal consumption of reagents and a mathematical model of the process of collective flotation of the desiccified barite product were determined. Satisfactory results have been obtained for the extraction of copper, zinc and lead into the collective concentrate. Collective flotation of the desiccated barite product under optimal conditions showed that non-ferrous metals are recovered under optimal conditions at a level of 98%.


  • On the prospects of using a modified sulfidizer in the processing of oxidized copper ores

    by G. L. Katkeeva, G. Burkitseterkyzy, I. M. Oskembekov, E. M. Zhunusov

    In order to improve the efficiency of sulfidization methods for oxidized ores, the problem of reducing the energy intensity of the process must be solved. In this regard, a promising method is the sulfidization of oxidized copper ores using a modified reagent that allows the process to be conducted without heating or any separate equipment. The modified sulfidizing agent designed to improve the efficiency of flotation concentration is produced by the mixing of sodium polysulfide and ammonium sulfate solutions. Comparative flotation experiments were conducted using pre-sulfidized oxidized copper ore containing 1.2 % of total copper, of which 1.08 % (or 90 %) was oxidized copper. The possibility of carrying out the sulfidization process in a flotation cell without forced heating of the reaction mixture has been established. At the same time, the modified reagent exceeds sodium polysulfide in terms of its flotation efficiency by 5 %. The chemical analysis of the processing products for the content of oxidized copper has demonstrated that its mass fraction decreased from 1.08 to 0.63 %. The experimental design method has been used to establish the best application conditions for the modified reagent. These are: the reagent consumption of 2.6 kg/t; slurry agitation with the sulfidizing agent for four minutes; and the collector (potassium butyl xanthate) consumption for the flotation process of 500 g/t. The copper recovery was 69.85 %. A mathematical model was designed for the flotation process with preliminary sulfidization of the oxidized copper ore in the form of a generalized miltifactorial equation.The work was performed with the grant support of the Ministry of Education and Science of the Republic of Kazakhstan (grant No. AP05130143).


  • Sulfidization application during the processing of oxidized copper ores of Udokan deposit

    by Astana Scientific-Technological Center “Parasat”, N. S. Bekturganov, G. L. Katkeeva, I. M. Oskembekov, M. A. Akubaeva

    This paper gives the investigation results of sulfidizing of oxidized copper ores of Udokan deposit and influence of this process on concentratibility. Sulfidizing was carried out in autoclave with the temperature of 160 °C with application of element sulfur. Mathematical model of hydrothermal sulfidizing of Udokan ore was obtained by probabilistic-determined planning of experiment. The factors of hydrothermal sulfidizing are process temperature, duration, sulfur consumption on oxidized copper sulfidizing, and sodium sulfate consumption according to the consumed sulfur. Sulfidizing technology of oxidized copper ores by sodium polysulfide with 85 °C temperature in cell was offered for the purpose of decreasing of energy intensity of this process. There was obtained the mathematical model of the process, showing the influence of sulfidizing factors on copper mineral flotation. The possibility of use of low-disperse element sulfur during the synthesis of polysulfide solutions was investigated together with their usage as sulphidizer at the temperature of 80 °C. Application of low-disperse sulfur provides the decrease of energy intensity of solution obtaining. Besides, sulfiding properties of obtained reagents are changed. According to the obtained results, copper extraction with ordinary sodium polysulfide is higher, than the one with sodium sulfide: copper extraction growing is ~13%. At the same time, sulfiding is the prospective method of increasing of benefication efficiency of oxidated copper ores of Udokan deposit. Every offered method allows the increasing of copper extraction in concentrate.