KYKehan Yan

Kehan Yan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kehan Yan has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Comprehensive Analysis of Misalignment Effects on Radial-Flux Dual Rotor Direct-Drive Motors

    by Kehan Yan, Zunyan Hu, Jianqiu Li, Liangfei Xu, Minggao Ouyang

    Direct-drive dual-rotor motors (DRMs) are susceptible to performance degradation under inappropriate skewing and axis misalignment. This paper evaluates the impacts of various skew modes on large-diameter DRM performance along with stator-rotor eccentricity consideration. First, the configuration and the segment skew mode of the targeted DRM are demonstrated in detail. Then, a simplified bidirectional skew and axis misalignment model is proposed for a unified field oriented control (FOC) strategy. Analytical results show that it is the skew angle rather than the skew direction that affects DRM mechanical performance. However, the 3D flux vector distribution demonstrates that when the skewed segments of the inner and outer rotor are contra-directional, a unique circular flux in the radial cross-section and a balanced flux distribution in the axial cross-section are formed. Moreover, the spatiotemporal harmonic analysis reveals the barrel effect of the inner air-gap and the distinct influence of contra-skew on high-frequency harmonics. Overall, a contra-skew angle not exceeding 15 electrical degrees provides an effective design compromise among torque capability, torque ripple, and axial force. Finally, two skewed automotivegrade DRM prototypes are fabricated and measured for axis misalignment, and the torque generation and light flux-weakening (FW) characteristics of the selected prototype are experimentally validated.

  • Parameter Matching Principle for Dual-Rotor In-Wheel Motors via Coupling Effect Exploitation

    by Kehan Yan, Ming Yang, Zunyan Hu, Jianqiu Li, Liangfei Xu, Minggao Ouyang

    Single-mechanical-port dual-rotor motors (DRMs) represent a promising topology for next-generation electric machines (EMs). However, the optimal parameter-matching principle between the two rotors and the stator in radial-flux configurations has not been sufficiently explored due to geometric asymmetry. This article proposes a parameter-matching principle that explicitly exploits the magnetic coupling effect. By conceptually segregating the DRM into two equivalent single-rotor EMs, the proposed principle enables accurate identification of optimally matched DRM designs, independent of optimization history. Targeting in-wheel motor (IWM) applications, the influence of parameter matching on torque and loss is systematically analyzed in the torque–loss power design space. A set of effective matching conditions are then formulated based on coupling-related geometric metrics. Additional influencing factors, including operating condition fluctuations and core material variations, are also investigated. Results reveal that the effective matching envelope primarily occupies the central region of the Pareto front rather than covering all Pareto-optimal designs. This highlights the necessity of coupling-based selection to avoid arbitrary choices from Pareto fronts. Finally, an automotive-grade DRM prototype designed under the proposed principle was fabricated and experimentally validated, achieving a peak torque exceeding 1500 Nm and a maximum efficiency above 92%, confirming the effectiveness of the proposed principle.


  • Comparison and experimental validation of cogging torque reduction methods for high-pole-number Halbach motors considering manufacturing tolerance effects

    by Jinpeng Song, Jianqiu Li, Zunyan Hu, Kehan Yan, Le Chen, Minggao Ouyang

    High-pole-number Halbach permanent magnet synchronous motors (PMSMs) exhibit excellent torque density and low harmonic distortion but suffer from severe cogging torque, which limits smooth operation and acoustic performance. This paper presents a comprehensive comparative study of three cogging torque reduction methods—magnet shifting, magnet shaping, and rotor step skewing—applied to a high-pole-number Halbach PMSMs, with particular emphasis on their effectiveness under manufacturing tolerances. Finite element simulations are conducted to evaluate each method’s impact on cogging torque, no-load back electromotive force (No-load Back-EMF) fundamental amplitude, and total harmonic distortion (THD). A tolerance sensitivity analysis is performed using the One-Factor-at-a-Time (OFTA) approach, considering key geometric deviations including magnet, stator slot, and static eccentricity. Among the three methods, magnet shifting demonstrates the most favorable balance between torque suppression and robustness, achieving over 95% cogging torque reduction with minimal degradation in No-load Back-EMF amplitude performance. Experimental validation on a 28-pole-pair, 168-slot prototype confirms the simulation accuracy, showing a cogging torque reduction from 40.8 to 1.85 N m, and validating the method’s practical feasibility.

  • Influence of the Wheel Rim Size on Different In-Wheel Motor Topologies

    by Kehan Yan, Ben Zhang, Zunyan Hu, Jianqiu Li, Liangfei Xu, Minggao Ouyang

    A comparison of in-wheel motors (IWMs) across different vehicle classes is difficult owing to considerable variations in size, power constraints, and the characteristics of IWM topologies. To address these issues, an objective comparison methodology for IWMs using the wheel rim as a mediator is proposed. First, the configurations of four typical IWM topologies with cooling systems are defined. Then, by analyzing the relation between wheel rim, tire, and vehicle, the standard wheel rim size is recognized as an important constraint for comparison. Moreover, four IWM topologies are optimized regarding torque volume density and duty-cycle efficiency across different rim sizes for the selection of representative designs. Finally, the Pareto front designs of each topology and rim size are discussed electromagnetically and thermally via validated finite-element analysis (FEA). Results show that the wheel rim size considerably impacted the performance of IWMs. Energy consumption reduction is crucial for IWMs application in vehicles with rims up to 16 in. For 18-in rim vehicles, the double-rotor integral slot motor exceeds vehicle torque requirements along with energy consumption benefits, enabling further drivetrain configuration innovation. The 20-in rims eliminate the difficulty of reducer installation, which enhances torque density for inner rotor fractional-slot motors.


  • A critical review of radial field in-wheel motors: technical progress and future trends

    by Kehan Yan, Zunyan Hu, Jiayi Hu, Jianqiu Li, Ben Zhang, Jinpeng Song, Jingkang Li, Le Chen, Hang Li, Liangfei Xu