Saofee Dueramae
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Saofee Dueramae has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Akkadath Abdulmatin
Department of Civil Engineering, Faculty of Engineering, Princess of Naradhiwas University (PNU), Narathiwas 96000, Thailand
2 shared publications Akkadath Abdulmatin
Department of Civil Engineering, Faculty of Engineering, Princess of Naradhiwas University (PNU), Narathiwas 96000
1 shared publicationApai Benchaphong
Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep, Bangkok, Thailand
1 shared publication- Apai Benchaphong
Center of Excellence in Infrastructure Materials Research and Testing (CE-IMRT), Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep (RMUTK), Bangkok 10120, Thailand
1 shared publication - Apiwish Thongraksa
Center of Excellence in Infrastructure Materials Research and Testing (CE-IMRT), Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep (RMUTK), Bangkok 10120, Thailand
1 shared publication Chai Jaturapitakkul
Department of Civil Engineering, Faculty of Engineering, King Mongkut’s University of Technology Thonburi (KMUTT), Bangkok 10140
1 shared publication
Latest Publications
- Open Access
- 1 February 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (2) , 774-784
Compressive Strength and Acid Resistance of Fly Ash Based One-Part Geopolymer
This research studied the properties of one-part geopolymer mortar using a binder from high calcium fly ash. Sodium metasilicate (SM) and sodium hydroxide (SH) were used as solid alkali activators at ratios of 1:1 and 1:2. This study focused on the effect of the dosage and the solid ratio of the alkali activator from SM and SH for the potential to produce a one-part geopolymer. The compressive strength and corrosion resistance of mortar due to sulfuric acid and hydrochloric acid were investigated. The results showed that using a high amount of sodium metasilicate and sodium hydroxide could enhance the development of compressive strength. The fly ash-based one-part geopolymer using sodium metasilicate and sodium hydroxide (SM: NH) at a ratio of 1:1 at 18% achieved the highest compressive strength of 13.3 MPa at 60 days. For the acid attack, it was found that the fly ash-based one-part geopolymer mortar using SM: NH at a ratio of 1:1 had a lower weight change than a ratio of 1:2 after immersion in sulfuric acid. Meanwhile, the fly ash-based one-part geopolymer mortar with SM: NH at a ratio of 1:2 showed higher resistance to hydrochloric acid than at a ratio of 1:1.
- 1 February 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (2) , 774-784
Open AccessCompressive Strength and Acid Resistance of Fly Ash Based One-Part Geopolymer
This research studied the properties of one-part geopolymer mortar using a binder from high calcium fly ash. Sodium metasilicate (SM) and sodium hydroxide (SH) were used as solid alkali activators at ratios of 1:1 and 1:2. This study focused on the effect of the dosage and the solid ratio of the alkali activator from SM and SH for the potential to produce a one-part geopolymer. The compressive strength and corrosion resistance of mortar due to sulfuric acid and hydrochloric acid were investigated. The results showed that using a high amount of sodium metasilicate and sodium hydroxide could enhance the development of compressive strength. The fly ash-based one-part geopolymer using sodium metasilicate and sodium hydroxide (SM: NH) at a ratio of 1:1 at 18% achieved the highest compressive strength of 13.3 MPa at 60 days. For the acid attack, it was found that the fly ash-based one-part geopolymer mortar using SM: NH at a ratio of 1:1 had a lower weight change than a ratio of 1:2 after immersion in sulfuric acid. Meanwhile, the fly ash-based one-part geopolymer mortar with SM: NH at a ratio of 1:2 showed higher resistance to hydrochloric acid than at a ratio of 1:1.
- Open Access
- 1 December 2025
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3160 (1)
Mechanical properties of lightweight concrete using EPS beads as coarse aggregate replacement
This research aims to examine the mechanical behavior of lightweight concrete produced by replacing natural coarse aggregates with expanded polystyrene (EPS) beads. The difference particle sized of EPS beads with diameter of 2.0 and 5.0 mm was used to replaced natural coarse aggregate (crushed limestone) at the rates of 35, 50 and 65% by volume. The compressive strength of concrete was evaluated at 7, 14 and 28 days. Additionally, the mechanical properties in term of splitting tensile strength and elastic modulus of concrete were also measured at 28 days. The results demonstrated that the compressive strength of the concrete reduced with increasing EPS bead replacement. However, specimens with smaller EPS beads exhibited slightly higher compressive strength compared to those with larger beads. Using 35% EPS beads with size of 2.0 mm as artificial aggregate to replace coarse aggregate resulted in compressive strengths of 28.3, 31.2, and 34.5 MPa at 7, 14, and 28 days, respectively. All the concrete can be classified as lightweight concrete for structures due to its compressive strength being higher than 17 MPa. Splitting tensile strength and elastic modulus of concrete depended on concrete strength similar to conventional concrete using natural coarse aggregate.
- 1 December 2025
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3160 (1)
Open AccessMechanical properties of lightweight concrete using EPS beads as coarse aggregate replacement
This research aims to examine the mechanical behavior of lightweight concrete produced by replacing natural coarse aggregates with expanded polystyrene (EPS) beads. The difference particle sized of EPS beads with diameter of 2.0 and 5.0 mm was used to replaced natural coarse aggregate (crushed limestone) at the rates of 35, 50 and 65% by volume. The compressive strength of concrete was evaluated at 7, 14 and 28 days. Additionally, the mechanical properties in term of splitting tensile strength and elastic modulus of concrete were also measured at 28 days. The results demonstrated that the compressive strength of the concrete reduced with increasing EPS bead replacement. However, specimens with smaller EPS beads exhibited slightly higher compressive strength compared to those with larger beads. Using 35% EPS beads with size of 2.0 mm as artificial aggregate to replace coarse aggregate resulted in compressive strengths of 28.3, 31.2, and 34.5 MPa at 7, 14, and 28 days, respectively. All the concrete can be classified as lightweight concrete for structures due to its compressive strength being higher than 17 MPa. Splitting tensile strength and elastic modulus of concrete depended on concrete strength similar to conventional concrete using natural coarse aggregate.
- Open Access
- 21 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10786
The Development of Fiber–Cement Flat Sheets by Young and Mature Coconut Fibers to Replace Asbestos for Eco-Friendly Products
This study investigated young and mature coconut fibers as an asbestos replacement in fiber–cement flat sheets. The ratio of fiber content ranged from 5% to 9.5% in increments of 0.5% by weight of binder. Crushed rock dust (CRD) was also utilized in this study at a ratio of 50% as sand replacement. The results showed that the addition of young coconut fiber (YCF) and mature coconut fiber (MCF) in flat sheets increased with decreasing bulk density and thermal conductivity. The optimum fiber content was 6.5%–7% by weight of binder for two types of fiber with the highest modulus of rupture of 12–13 MPa. The modulus of rupture and density of fiber–cement flat sheets using YCF were higher than that of fiber–cement flat sheets using MCF, which was clarified by SEM results due to the denser structure of MCF. Moreover, the modulus of rupture was directly proportional to the modulus of elasticity in fiber–cement flat sheets.
- 21 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10786
Open AccessThe Development of Fiber–Cement Flat Sheets by Young and Mature Coconut Fibers to Replace Asbestos for Eco-Friendly Products
This study investigated young and mature coconut fibers as an asbestos replacement in fiber–cement flat sheets. The ratio of fiber content ranged from 5% to 9.5% in increments of 0.5% by weight of binder. Crushed rock dust (CRD) was also utilized in this study at a ratio of 50% as sand replacement. The results showed that the addition of young coconut fiber (YCF) and mature coconut fiber (MCF) in flat sheets increased with decreasing bulk density and thermal conductivity. The optimum fiber content was 6.5%–7% by weight of binder for two types of fiber with the highest modulus of rupture of 12–13 MPa. The modulus of rupture and density of fiber–cement flat sheets using YCF were higher than that of fiber–cement flat sheets using MCF, which was clarified by SEM results due to the denser structure of MCF. Moreover, the modulus of rupture was directly proportional to the modulus of elasticity in fiber–cement flat sheets.
- Open Access
- 30 September 2024
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 74 (355) , e351
An investigation of palm oil fuel ash and limestone powder for use in sustainable high strength concrete construction
This study deals with the production of concrete with low CO2 emissions. For this reason, two materials, namely palm oil fuel ash (POFA) and limestone powder (LP), were used as mineral additions to replace conventional cement as much as possible. The results showed that concrete containing 60 wt% POFA could achieve the high strength requirements of ACI 363R from an age of 28 days. At a replacement level of 70 wt% of admixtures, the use of 10 wt% LP + 60 wt% POFA was a good mixture as it had the highest concrete compressive strength, had a minor effect on shrinkage strain and reduced heat generation by approximately 50% compared to cement concrete. Additionally, the use of POFA and LP is a good choice to produce environmentally friendly concrete, which can reduce the CO2 emissions of concrete by about 44–62% compared to cement concrete at similar strength.
- 30 September 2024
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 74 (355) , e351
Open AccessAn investigation of palm oil fuel ash and limestone powder for use in sustainable high strength concrete construction
This study deals with the production of concrete with low CO2 emissions. For this reason, two materials, namely palm oil fuel ash (POFA) and limestone powder (LP), were used as mineral additions to replace conventional cement as much as possible. The results showed that concrete containing 60 wt% POFA could achieve the high strength requirements of ACI 363R from an age of 28 days. At a replacement level of 70 wt% of admixtures, the use of 10 wt% LP + 60 wt% POFA was a good mixture as it had the highest concrete compressive strength, had a minor effect on shrinkage strain and reduced heat generation by approximately 50% compared to cement concrete. Additionally, the use of POFA and LP is a good choice to produce environmentally friendly concrete, which can reduce the CO2 emissions of concrete by about 44–62% compared to cement concrete at similar strength.
- Open Access
- 1 July 2024
- Published by Ital Publication in Civil Engineering Journal
- Vol. 10 (7) , 2195-2215
Strength and Acid Resistance of Mortar with Different Binders from Palm Oil Fuel Ash, Slag, and Calcium Carbide Residue
This study deals with the use of ground palm oil fuel ash (GPOFA) in combination with ground granulated blast furnace slag (GGBFS) and ground calcium carbide residue (GCR) to produce the binary and ternary binders-based alkali activated mortar. The appropriate content of materials in each binder type was determined as a function of compressive strength. The results revealed that both GPOFA:GGBFS and GPOFA:GCR binders had an optimum blending ratio of 70:30 wt%, while the GPOFA:GGBFS:GCR binder was 55:30:15 wt%. An alkaline catalyst of NaOH was admixed to the best mixture in each binder type to stimulate the mortar's compressive strength. The sulfuric acid (H2SO4) resistance of the mortar in terms of weight change was also examined. The addition of 1M NaOH in both binary and ternary binders could enhance the compressive strength and H2SO4 resistance of the mortar. The highest compressive strength and lowest weight change due to soaking in H2SO4 solution were found in the ternary binder mortar with a 1 M NaOH. The mortar with GCR immersed in H2SO4 solution resulted in an increased weight, which was different from that of the mortar without GCR. The microstructural analysis of the alkali-activated pastes indicated more reaction products than in the case of the pastes without alkali activator. However, a higher concentration of 2 M NaOH resulted in a poor microstructure, which had a negative effect on the compressive strength and H2SO4resistance. Doi: 10.28991/CEJ-2024-010-07-08 Full Text: PDF
- 1 July 2024
- Published by Ital Publication in Civil Engineering Journal
- Vol. 10 (7) , 2195-2215
Open AccessStrength and Acid Resistance of Mortar with Different Binders from Palm Oil Fuel Ash, Slag, and Calcium Carbide Residue
This study deals with the use of ground palm oil fuel ash (GPOFA) in combination with ground granulated blast furnace slag (GGBFS) and ground calcium carbide residue (GCR) to produce the binary and ternary binders-based alkali activated mortar. The appropriate content of materials in each binder type was determined as a function of compressive strength. The results revealed that both GPOFA:GGBFS and GPOFA:GCR binders had an optimum blending ratio of 70:30 wt%, while the GPOFA:GGBFS:GCR binder was 55:30:15 wt%. An alkaline catalyst of NaOH was admixed to the best mixture in each binder type to stimulate the mortar's compressive strength. The sulfuric acid (H2SO4) resistance of the mortar in terms of weight change was also examined. The addition of 1M NaOH in both binary and ternary binders could enhance the compressive strength and H2SO4 resistance of the mortar. The highest compressive strength and lowest weight change due to soaking in H2SO4 solution were found in the ternary binder mortar with a 1 M NaOH. The mortar with GCR immersed in H2SO4 solution resulted in an increased weight, which was different from that of the mortar without GCR. The microstructural analysis of the alkali-activated pastes indicated more reaction products than in the case of the pastes without alkali activator. However, a higher concentration of 2 M NaOH resulted in a poor microstructure, which had a negative effect on the compressive strength and H2SO4resistance. Doi: 10.28991/CEJ-2024-010-07-08 Full Text: PDF