Akkadath Abdulmatin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Akkadath Abdulmatin has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Penpichcha Khongpermgoson Sanit-In
Department of Civil Engineering, Faculty of Engineering, Kasetsart University, Kamphaeng Saen Campus, Nakhon Pathom 73140, Thailand
2 shared publications - Saofee Dueramae
Center of Excellence in Infrastructure Materials Research and Testing (CE-IMRT), Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep (RMUTK), Bangkok 10120, Thailand
2 shared publications - Weerachart Tangchirapat
Department of Civil Engineering, Faculty of Engineering, King Mongkut’s University of Technology Thonburi, Bangkok 10140, Thailand
2 shared publications - Apai Benchaphong
Center of Excellence in Infrastructure Materials Research and Testing (CE-IMRT), Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep (RMUTK), Bangkok 10120, Thailand
1 shared publication - Apiwish Thongraksa
Center of Excellence in Infrastructure Materials Research and Testing (CE-IMRT), Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep (RMUTK), Bangkok 10120, Thailand
1 shared publication - Chai Jaturapitakkul
Faculty of Engineering, King Mongkut’s University of Technology Thonburi (KMUTT)
1 shared publication
Latest Publications
- Open Access
- 1 September 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (9) , 3716-3739
Damage-Sensitive Mechanical and Transport Properties of Concrete Under Cryogenic Exposure
This study investigates the residual performance of concrete after repeated cryogenic thermal shock and evaluates how water-to-binder (W/B) ratio, binder content, and fly ash replacement influence damage development. Seven concrete mixtures were tested at 28 days after up to three 1-hour liquid-nitrogen immersion cycles. Compressive strength, elastic modulus, reinforcing-bar bond strength and slip, length change, void content, and water permeability were examined to characterize load-bearing capacity, stiffness, interfacial behavior, deformation, and transport integrity. After three cycles, the control mixture retained 84% of its initial compressive strength but only 46% of its elastic modulus, demonstrating that stiffness was more sensitive to accumulated internal damage. First-cycle compressive-strength retention ranged from 65% to 99%, with mixtures having lower W/B ratio and higher binder content generally showing better retention. Bond strength decreased more modestly, whereas length-change records revealed rapid expansion during immersion and residual deformation after recovery. Void content increased after exposure, and measurable permeability generally increased, indicating development of connected transport paths; values unavailable after cracking were reported as N/A. The combined results show that elastic modulus, deformation, and transport properties complement compressive strength in assessing cryogenic damage and support performance-based selection of concrete mixtures for LNG-related structures.
- 1 September 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (9) , 3716-3739
Open AccessDamage-Sensitive Mechanical and Transport Properties of Concrete Under Cryogenic Exposure
This study investigates the residual performance of concrete after repeated cryogenic thermal shock and evaluates how water-to-binder (W/B) ratio, binder content, and fly ash replacement influence damage development. Seven concrete mixtures were tested at 28 days after up to three 1-hour liquid-nitrogen immersion cycles. Compressive strength, elastic modulus, reinforcing-bar bond strength and slip, length change, void content, and water permeability were examined to characterize load-bearing capacity, stiffness, interfacial behavior, deformation, and transport integrity. After three cycles, the control mixture retained 84% of its initial compressive strength but only 46% of its elastic modulus, demonstrating that stiffness was more sensitive to accumulated internal damage. First-cycle compressive-strength retention ranged from 65% to 99%, with mixtures having lower W/B ratio and higher binder content generally showing better retention. Bond strength decreased more modestly, whereas length-change records revealed rapid expansion during immersion and residual deformation after recovery. Void content increased after exposure, and measurable permeability generally increased, indicating development of connected transport paths; values unavailable after cracking were reported as N/A. The combined results show that elastic modulus, deformation, and transport properties complement compressive strength in assessing cryogenic damage and support performance-based selection of concrete mixtures for LNG-related structures.
- Open Access
- 1 February 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (2) , 774-784
Compressive Strength and Acid Resistance of Fly Ash Based One-Part Geopolymer
This research studied the properties of one-part geopolymer mortar using a binder from high calcium fly ash. Sodium metasilicate (SM) and sodium hydroxide (SH) were used as solid alkali activators at ratios of 1:1 and 1:2. This study focused on the effect of the dosage and the solid ratio of the alkali activator from SM and SH for the potential to produce a one-part geopolymer. The compressive strength and corrosion resistance of mortar due to sulfuric acid and hydrochloric acid were investigated. The results showed that using a high amount of sodium metasilicate and sodium hydroxide could enhance the development of compressive strength. The fly ash-based one-part geopolymer using sodium metasilicate and sodium hydroxide (SM: NH) at a ratio of 1:1 at 18% achieved the highest compressive strength of 13.3 MPa at 60 days. For the acid attack, it was found that the fly ash-based one-part geopolymer mortar using SM: NH at a ratio of 1:1 had a lower weight change than a ratio of 1:2 after immersion in sulfuric acid. Meanwhile, the fly ash-based one-part geopolymer mortar with SM: NH at a ratio of 1:2 showed higher resistance to hydrochloric acid than at a ratio of 1:1.
- 1 February 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (2) , 774-784
Open AccessCompressive Strength and Acid Resistance of Fly Ash Based One-Part Geopolymer
This research studied the properties of one-part geopolymer mortar using a binder from high calcium fly ash. Sodium metasilicate (SM) and sodium hydroxide (SH) were used as solid alkali activators at ratios of 1:1 and 1:2. This study focused on the effect of the dosage and the solid ratio of the alkali activator from SM and SH for the potential to produce a one-part geopolymer. The compressive strength and corrosion resistance of mortar due to sulfuric acid and hydrochloric acid were investigated. The results showed that using a high amount of sodium metasilicate and sodium hydroxide could enhance the development of compressive strength. The fly ash-based one-part geopolymer using sodium metasilicate and sodium hydroxide (SM: NH) at a ratio of 1:1 at 18% achieved the highest compressive strength of 13.3 MPa at 60 days. For the acid attack, it was found that the fly ash-based one-part geopolymer mortar using SM: NH at a ratio of 1:1 had a lower weight change than a ratio of 1:2 after immersion in sulfuric acid. Meanwhile, the fly ash-based one-part geopolymer mortar with SM: NH at a ratio of 1:2 showed higher resistance to hydrochloric acid than at a ratio of 1:1.
- Open Access
- 30 September 2024
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 74 (355) , e351
An investigation of palm oil fuel ash and limestone powder for use in sustainable high strength concrete construction
This study deals with the production of concrete with low CO2 emissions. For this reason, two materials, namely palm oil fuel ash (POFA) and limestone powder (LP), were used as mineral additions to replace conventional cement as much as possible. The results showed that concrete containing 60 wt% POFA could achieve the high strength requirements of ACI 363R from an age of 28 days. At a replacement level of 70 wt% of admixtures, the use of 10 wt% LP + 60 wt% POFA was a good mixture as it had the highest concrete compressive strength, had a minor effect on shrinkage strain and reduced heat generation by approximately 50% compared to cement concrete. Additionally, the use of POFA and LP is a good choice to produce environmentally friendly concrete, which can reduce the CO2 emissions of concrete by about 44–62% compared to cement concrete at similar strength.
- 30 September 2024
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 74 (355) , e351
Open AccessAn investigation of palm oil fuel ash and limestone powder for use in sustainable high strength concrete construction
This study deals with the production of concrete with low CO2 emissions. For this reason, two materials, namely palm oil fuel ash (POFA) and limestone powder (LP), were used as mineral additions to replace conventional cement as much as possible. The results showed that concrete containing 60 wt% POFA could achieve the high strength requirements of ACI 363R from an age of 28 days. At a replacement level of 70 wt% of admixtures, the use of 10 wt% LP + 60 wt% POFA was a good mixture as it had the highest concrete compressive strength, had a minor effect on shrinkage strain and reduced heat generation by approximately 50% compared to cement concrete. Additionally, the use of POFA and LP is a good choice to produce environmentally friendly concrete, which can reduce the CO2 emissions of concrete by about 44–62% compared to cement concrete at similar strength.