Diego Díaz-Salamanca
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diego Díaz-Salamanca has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Iñigo Llavori
Mechanics and Industrial Production, Faculty of Engineering, Mondragon Unibertsitatea, Loramendi 4, 20500 Mondragon, Spain
5 shared publications - Miguel Muñiz-Calvente
Department of Construction and Manufacturing Engineering, University of Oviedo, Gijón, Spain
5 shared publications - Abilio Manuel Pinho De Jesus
Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto, Portugal
2 shared publications Alaitz Zabala
2 shared publications- Alfonso Rodríguez Tejón
Department of Continuum Mechanics and Structural Theory, Gijón School of Engineering, University of Oviedo, Gijón Campus, 33203 Gijón, Spain
2 shared publications - Antonin Kanaval2 shared publications
Latest Publications
- Open Access
- 6 November 2026
- Published by Wiley in Computer Applications in Engineering Education
- Vol. 34 (6) , e70291
Teaching Topology Optimization Through Polymer Material Extrusion Prototyping: A Transferable CAD‐CAE‐AM Framework With Numerical‐Experimental Validation
This paper presents a transferable computer‐aided engineering educational framework for teaching topology optimization through polymer material extrusion prototyping and numerical‐experimental validation. The framework is intended to help students move from idealized numerical simulation toward design decisions constrained by manufacturability, physical testing and failure interpretation. It is organized as a compact six‐stage workflow: material characterization and calibration, baseline structural simulation, topology optimization and verification, computer‐aided design reconstruction and design for additive manufacturing, controlled prototyping, and physical testing with redesign where needed. Its feasibility was examined through a master‐level implementation in which five student teams, distributed across two course editions, optimized and tested a pin‐loaded polymer component required to withstand 500 N. The implementation provides descriptive, team‐level evidence of technical feasibility and educational traceability. Student reports and prototypes documented material calibration, manufacturable reconstruction of topology‐optimization outputs, and experimental validation of final designs. All reported final designs exceeded the 500 N requirement, with measured final masses between 14.25 and 19.55 g and experimental failure loads between 740 and 1300 N. The tests also revealed bending and buckling in slender optimized members, showing that stress‐based topology optimization must be complemented with stability checks and physical validation. The study contributes a reproducible educational framework that closes the design‐simulate‐optimize‐manufacture‐test cycle within a compact laboratory structure.
- 6 November 2026
- Published by Wiley in Computer Applications in Engineering Education
- Vol. 34 (6) , e70291
Open AccessTeaching Topology Optimization Through Polymer Material Extrusion Prototyping: A Transferable CAD‐CAE‐AM Framework With Numerical‐Experimental Validation
This paper presents a transferable computer‐aided engineering educational framework for teaching topology optimization through polymer material extrusion prototyping and numerical‐experimental validation. The framework is intended to help students move from idealized numerical simulation toward design decisions constrained by manufacturability, physical testing and failure interpretation. It is organized as a compact six‐stage workflow: material characterization and calibration, baseline structural simulation, topology optimization and verification, computer‐aided design reconstruction and design for additive manufacturing, controlled prototyping, and physical testing with redesign where needed. Its feasibility was examined through a master‐level implementation in which five student teams, distributed across two course editions, optimized and tested a pin‐loaded polymer component required to withstand 500 N. The implementation provides descriptive, team‐level evidence of technical feasibility and educational traceability. Student reports and prototypes documented material calibration, manufacturable reconstruction of topology‐optimization outputs, and experimental validation of final designs. All reported final designs exceeded the 500 N requirement, with measured final masses between 14.25 and 19.55 g and experimental failure loads between 740 and 1300 N. The tests also revealed bending and buckling in slender optimized members, showing that stress‐based topology optimization must be complemented with stability checks and physical validation. The study contributes a reproducible educational framework that closes the design‐simulate‐optimize‐manufacture‐test cycle within a compact laboratory structure.
- Open Access
- 4 November 2026
- Published by Elsevier in Engineering Failure Analysis
- Vol. 200
Influence of machining-induced surface integrity on high-cycle fatigue behavior: Application to 42CrMo4+QT steel
- 4 November 2026
- Published by Elsevier in Engineering Failure Analysis
- Vol. 200
Open AccessInfluence of machining-induced surface integrity on high-cycle fatigue behavior: Application to 42CrMo4+QT steel
- Open Access
- 7 September 2026
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 248
Fatigue assessment of galvanized slotted bolted joints: Combined experimental and numerical analysis
- 7 September 2026
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 248
Open AccessFatigue assessment of galvanized slotted bolted joints: Combined experimental and numerical analysis
- Open Access
- 19 August 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Machining-Induced Surface Integrity on High-Cycle Fatigue Behavior: Application to 42CrMo4+QT Steel
In the present study, a comprehensive methodology to assess the impact of surface integrity on fatigue behavior is developed. First, an artificial neural network (ANN) model was developed to correlate machining conditions with surface integrity, enabling the design of specific scenarios with varying levels of roughness and residual stress. Accordingly, 42CrMo4+QT steel specimens were machined and subsequently tested in the high-cycle fatigue (HCF) regime at a stress ratio of R = 0.1 until failure. The outcomes of each scenario were critically evaluated, enabling an in-depth discussion on how the coupled effects of residual stresses and surface roughness dictate overall fatigue life. The study of the roughness effect shows that the use of standard roughness parameters, such as Ra, may be inadequate, as differing values may yield similar stress concentration factors. Moreover, experimental data demonstrate that fatigue life is predominantly governed by residual stresses rather than surface roughness. Finally, the feasibility of existing correction strategies is critically discussed, accounting for cyclic residual stress relaxation and microstructural fracture features.
- 19 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Machining-Induced Surface Integrity on High-Cycle Fatigue Behavior: Application to 42CrMo4+QT Steel
In the present study, a comprehensive methodology to assess the impact of surface integrity on fatigue behavior is developed. First, an artificial neural network (ANN) model was developed to correlate machining conditions with surface integrity, enabling the design of specific scenarios with varying levels of roughness and residual stress. Accordingly, 42CrMo4+QT steel specimens were machined and subsequently tested in the high-cycle fatigue (HCF) regime at a stress ratio of R = 0.1 until failure. The outcomes of each scenario were critically evaluated, enabling an in-depth discussion on how the coupled effects of residual stresses and surface roughness dictate overall fatigue life. The study of the roughness effect shows that the use of standard roughness parameters, such as Ra, may be inadequate, as differing values may yield similar stress concentration factors. Moreover, experimental data demonstrate that fatigue life is predominantly governed by residual stresses rather than surface roughness. Finally, the feasibility of existing correction strategies is critically discussed, accounting for cyclic residual stress relaxation and microstructural fracture features.
- Open Access
- 4 May 2026
- Published by Elsevier in SSRN Electronic Journal
Fatigue Assessment of Galvanized Slotted Bolted Joints: Combined Numerical and Experimental Analysis
The ongoing large-scale deployment of renewable energy technologies aimed at reducing dependence on fossil fuels has led to the widespread use of structural details that are not explicitly covered by current fatigue design standards, posing significant challenges for their reliable assessment. Among them, preloaded slotted bolted joints are commonly adopted in solar tracker structures owing to their capability to accommodate assembly tolerances and on-site misalignments. Although these joints are typically designed according to a slip-resistant philosophy, their fatigue performance under cyclic loading below their slip load has not yet been addressed in the specialized literature. To address this gap, the present study investigates several joint configurations representative of solar tracker connections under static and fatigue loading, considering different levels of bolt preload. A combined experimental and numerical approach was adopted, in which static tests were first used to determine the slip resistance of the joints, and subsequently, their fatigue behavior was analyzed under load levels deliberately selected to be below their slip failure. In parallel, detailed finite element models were developed, and fatigue life predictions were performed using different local strain-based and multiaxial fatigue approaches. The results demonstrate strong agreement between numerical predictions and experimental observations, indicating that preloaded bolted connections with slotted holes, commonly employed in solar structures, do not exhibit fatigue damage when subjected to loads below their slip resistance, with fatigue lives exceeding the investigated cycle range.
- 4 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFatigue Assessment of Galvanized Slotted Bolted Joints: Combined Numerical and Experimental Analysis
The ongoing large-scale deployment of renewable energy technologies aimed at reducing dependence on fossil fuels has led to the widespread use of structural details that are not explicitly covered by current fatigue design standards, posing significant challenges for their reliable assessment. Among them, preloaded slotted bolted joints are commonly adopted in solar tracker structures owing to their capability to accommodate assembly tolerances and on-site misalignments. Although these joints are typically designed according to a slip-resistant philosophy, their fatigue performance under cyclic loading below their slip load has not yet been addressed in the specialized literature. To address this gap, the present study investigates several joint configurations representative of solar tracker connections under static and fatigue loading, considering different levels of bolt preload. A combined experimental and numerical approach was adopted, in which static tests were first used to determine the slip resistance of the joints, and subsequently, their fatigue behavior was analyzed under load levels deliberately selected to be below their slip failure. In parallel, detailed finite element models were developed, and fatigue life predictions were performed using different local strain-based and multiaxial fatigue approaches. The results demonstrate strong agreement between numerical predictions and experimental observations, indicating that preloaded bolted connections with slotted holes, commonly employed in solar structures, do not exhibit fatigue damage when subjected to loads below their slip resistance, with fatigue lives exceeding the investigated cycle range.
- Open Access
- 27 August 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (5-6) , 2897-2919
Influence of turning parameters on residual stresses and roughness of 42CrMo4 + QT
Residual stresses and surface roughness have been recognized to play a critical role in the fatigue strength of metal components. Machining processes can induce different roughness and residual stress conditions depending on the parameters used in the process. Therefore, it is essential to develop knowledge that helps to predict the residual stresses and roughness that would be obtained from different machining conditions. Due to the growing interest from the industry in the use of 42CrMo4 steel because of its excellent mechanical properties, the main objective of this work is to establish two phenomenological models to accurately predict the residual stress and roughness values in turned specimens of this material. The models are derived from data of four process variables: (a) insert tip radius; (b) feed rate; (c) cutting speed; and (d) depth of cut. For this purpose, a wide experimental campaign has been developed, which includes the machining of 68 specimens under various cutting scenarios, and their subsequent measurement of residual stresses and roughness. Once the experimental data were obtained, the response surface method based on the central composite design was used to fit the models, obtaining a correlation index $${R}^{2}$$ higher than 0.9 in both cases. In this article, it is concluded that feed rate and insert radius have a greater effect on the residual stress and roughness obtained, while cutting speed and depth of cut have a lesser impact on the results. It is hoped that the findings will establish a groundwork for the machining of this material type, ensuring controlled conditions of residual stress and roughness.- 27 August 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (5-6) , 2897-2919
Open AccessInfluence of turning parameters on residual stresses and roughness of 42CrMo4 + QT
Residual stresses and surface roughness have been recognized to play a critical role in the fatigue strength of metal components. Machining processes can induce different roughness and residual stress conditions depending on the parameters used in the process. Therefore, it is essential to develop knowledge that helps to predict the residual stresses and roughness that would be obtained from different machining conditions. Due to the growing interest from the industry in the use of 42CrMo4 steel because of its excellent mechanical properties, the main objective of this work is to establish two phenomenological models to accurately predict the residual stress and roughness values in turned specimens of this material. The models are derived from data of four process variables: (a) insert tip radius; (b) feed rate; (c) cutting speed; and (d) depth of cut. For this purpose, a wide experimental campaign has been developed, which includes the machining of 68 specimens under various cutting scenarios, and their subsequent measurement of residual stresses and roughness. Once the experimental data were obtained, the response surface method based on the central composite design was used to fit the models, obtaining a correlation index $${R}^{2}$$ higher than 0.9 in both cases. In this article, it is concluded that feed rate and insert radius have a greater effect on the residual stress and roughness obtained, while cutting speed and depth of cut have a lesser impact on the results. It is hoped that the findings will establish a groundwork for the machining of this material type, ensuring controlled conditions of residual stress and roughness. - Open Access
- 3 August 2024
- Published by Elsevier in Data in Brief
- Vol. 56, 110793
Turning of 42CrMo4+QT under different scenarios: Dataset of machining, roughness and residual stress
- 3 August 2024
- Published by Elsevier in Data in Brief
- Vol. 56, 110793
Open AccessTurning of 42CrMo4+QT under different scenarios: Dataset of machining, roughness and residual stress