Han Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Han Wang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Yingtao Ding
School of Integrated Circuits and Electronics, Beijing Institute of Technology, Beijing 100081, China
3 shared publications - Zhiming Chen
Beijing Institute of Technology
3 shared publications - Ziyue Zhang
School of Integrated Circuits and Electronics, Beijing Institute of Technology, Beijing 100081, China
3 shared publications Yangyang Yan
Chongqing Institute of Microelectronics and Microsystems, Beijing Institute of Technology, Chongqing, China
2 shared publications- Yigang Hao
School of Integrated Circuits and Electronics, Beijing Institute of Technology, Beijing, China
2 shared publications Ziru Cai
School of Integrated Circuits and Electronics, Beijing Institute of Technology, Beijing, China
2 shared publications
Latest Publications
- 6 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (1) , 140-143
Double-Sided Fabrication of TSV Interposer With Parylene-Based Damascene RDLs Achieved by Selective Electroless Plating
In this letter, a novel double-sided fabrication scheme for Si interposer composed of through-silicon-vias (TSVs) and re-distribution layers (RDLs) is proposed. The ultra-deep TSVs are manufactured based on through-vias by double-sided processes. After chemical mechanical polishing (CMP) on both sides, a novel Damascene pro-cess based on selective electroless plating (ELP) is carried out to fabricate RDLs with parylene dielectric layers, in which the Cu RDLs are selectively formed in etched pat-terns as the catalysts are only reserved in these regions by incorporating a lift-off step into ELP. Note that the fabrica-tion scheme shows good conformability across the 4-inch wafer, which exhibits a small warpage of only 64.7 μm. Measurement results highlight the good electrical perfor-mance of the fabricated TSVs in terms of keeping stable parasitic capacitance as low as 565 fF in the range of -40 V to 40 V, and low leakage current of 1.21 pA at 20 V.
- 6 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (1) , 140-143
Double-Sided Fabrication of TSV Interposer With Parylene-Based Damascene RDLs Achieved by Selective Electroless Plating
In this letter, a novel double-sided fabrication scheme for Si interposer composed of through-silicon-vias (TSVs) and re-distribution layers (RDLs) is proposed. The ultra-deep TSVs are manufactured based on through-vias by double-sided processes. After chemical mechanical polishing (CMP) on both sides, a novel Damascene pro-cess based on selective electroless plating (ELP) is carried out to fabricate RDLs with parylene dielectric layers, in which the Cu RDLs are selectively formed in etched pat-terns as the catalysts are only reserved in these regions by incorporating a lift-off step into ELP. Note that the fabrica-tion scheme shows good conformability across the 4-inch wafer, which exhibits a small warpage of only 64.7 μm. Measurement results highlight the good electrical perfor-mance of the fabricated TSVs in terms of keeping stable parasitic capacitance as low as 565 fF in the range of -40 V to 40 V, and low leakage current of 1.21 pA at 20 V.
- 13 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 15 (7) , 1385-1391
An Experimental Study on a Barrier-Less Cu Interconnect Scheme With Polyimide Insulator for Cost-Effective 3-D Packaging
Polyimide (PI) has been widely used as the insulator material in the Cu interconnect system for three-dimensional (3D) advanced packaging. In general, a barrier layer is required between PI and Cu to suppress Cu diffusion, which increases the fabrication cost and complexity. In this article, we experimentally investigate the feasibility of a barrier-less Cu interconnect scheme with PI insulator while omitting the typical barrier layer. The diffusion phenomenon of sputtered Cu in PI is evaluated by the energy dispersive X-ray spectroscopy (EDX) analyses and the Fourier transform infrared spectroscopy (FTIR) tests. It is revealed that the PI layer with sufficient thickness can prevent the Cu atoms from diffusing into the Si substrate even after annealing at 300 °C for 1 h. Electrical measurement results based on the Cu-PI-Si structure show that the leakage currents are relatively small across various test temperatures, and there is little degradation in the insulating performance of PI after annealing. Moreover, time dependent dielectric breakdown (TDDB) tests are carried out and the mean-time-to-failure (MTTF) of PI before or after annealing is estimated to be more than 10 years for electric fields less than 1.45 MV/cm or 1.25 MV/cm, respectively. Therefore, the proposed barrier-less Cu interconnect scheme with PI insulator demonstrates feasibility in terms of insulating performance and long-term reliability. This scheme is further implemented in the vertical through-silicon-via (TSV) structure by a low-cost fabrication flow, which exhibits good electrical performance in both the leakage current and the parasitic capacitance.
- 13 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 15 (7) , 1385-1391
An Experimental Study on a Barrier-Less Cu Interconnect Scheme With Polyimide Insulator for Cost-Effective 3-D Packaging
Polyimide (PI) has been widely used as the insulator material in the Cu interconnect system for three-dimensional (3D) advanced packaging. In general, a barrier layer is required between PI and Cu to suppress Cu diffusion, which increases the fabrication cost and complexity. In this article, we experimentally investigate the feasibility of a barrier-less Cu interconnect scheme with PI insulator while omitting the typical barrier layer. The diffusion phenomenon of sputtered Cu in PI is evaluated by the energy dispersive X-ray spectroscopy (EDX) analyses and the Fourier transform infrared spectroscopy (FTIR) tests. It is revealed that the PI layer with sufficient thickness can prevent the Cu atoms from diffusing into the Si substrate even after annealing at 300 °C for 1 h. Electrical measurement results based on the Cu-PI-Si structure show that the leakage currents are relatively small across various test temperatures, and there is little degradation in the insulating performance of PI after annealing. Moreover, time dependent dielectric breakdown (TDDB) tests are carried out and the mean-time-to-failure (MTTF) of PI before or after annealing is estimated to be more than 10 years for electric fields less than 1.45 MV/cm or 1.25 MV/cm, respectively. Therefore, the proposed barrier-less Cu interconnect scheme with PI insulator demonstrates feasibility in terms of insulating performance and long-term reliability. This scheme is further implemented in the vertical through-silicon-via (TSV) structure by a low-cost fabrication flow, which exhibits good electrical performance in both the leakage current and the parasitic capacitance.
- 12 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6249-6253
A Novel Double-Sided Etching and Electroplating Fabrication Scheme for Coaxial Through-Silicon-Vias in 3-D Integration
Compared to conventional through-silicon-via (TSV) technology, coaxial TSVs can provide better radio frequency (RF) transmission performance in terms of reduced transmission loss and enhanced impedance matching in 2.5-D/3-D heterogeneous integration of RF microsystems. This article presents a novel fabrication scheme for coaxial TSVs comprised of Cu-pillar inner conductors, annular benzocyclobutene (BCB) insulators, and annular Cu outer conductors. Complete Cu conductors are achieved by the proposed double-sided etching and electroplating method, in which the outer and inner conductors are fabricated from the front and back sides of the wafer, respectively. Besides, a thick BCB insulator without voids is realized based on the vacuum-assisted spin-filling technique. Due to the good feasibility of the fabrication processes, the dimensions of the coaxial TSV can be flexibly designed to meet the requirements for impedance matching. Coaxial TSVs with a height of 85 $\mu $ m, an inner conductor diameter of 45 $\mu $ m, and an insulator thickness of 53 $\mu $ m are successfully fabricated. Measurement results show that the TSVs exhibit a low leakage current between the inner and outer conductors of 1.28 pA at 20 V, and the return loss and insertion loss are better than $-$ 16 and $-$ 0.35 dB up to 40 GHz, respectively. Such compact and low-loss coaxial TSV structure together with its fabrication scheme facilitates the miniaturized, high-density, and high-performance 2.5-D/3-D heterogeneous integration of microsystems at RF and millimeter-wave (MMW) frequencies.
- 12 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6249-6253
A Novel Double-Sided Etching and Electroplating Fabrication Scheme for Coaxial Through-Silicon-Vias in 3-D Integration
Compared to conventional through-silicon-via (TSV) technology, coaxial TSVs can provide better radio frequency (RF) transmission performance in terms of reduced transmission loss and enhanced impedance matching in 2.5-D/3-D heterogeneous integration of RF microsystems. This article presents a novel fabrication scheme for coaxial TSVs comprised of Cu-pillar inner conductors, annular benzocyclobutene (BCB) insulators, and annular Cu outer conductors. Complete Cu conductors are achieved by the proposed double-sided etching and electroplating method, in which the outer and inner conductors are fabricated from the front and back sides of the wafer, respectively. Besides, a thick BCB insulator without voids is realized based on the vacuum-assisted spin-filling technique. Due to the good feasibility of the fabrication processes, the dimensions of the coaxial TSV can be flexibly designed to meet the requirements for impedance matching. Coaxial TSVs with a height of 85 $\mu $ m, an inner conductor diameter of 45 $\mu $ m, and an insulator thickness of 53 $\mu $ m are successfully fabricated. Measurement results show that the TSVs exhibit a low leakage current between the inner and outer conductors of 1.28 pA at 20 V, and the return loss and insertion loss are better than $-$ 16 and $-$ 0.35 dB up to 40 GHz, respectively. Such compact and low-loss coaxial TSV structure together with its fabrication scheme facilitates the miniaturized, high-density, and high-performance 2.5-D/3-D heterogeneous integration of microsystems at RF and millimeter-wave (MMW) frequencies.