Joana Tátá
Joana Tátá has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- António Teixeira
IEETA, DETI, LASI, University of Aveiro, Aveiro, Portugal
2 shared publications - João Santos
PICadvanced, S.A., 3830-352 Ílhavo, Portugal
2 shared publications - Carla Rodrigues
PICadvanced S.A., Edifício Central, PCI- Creative Science Park, Via do Conhecimento, 3830-352 Aveiro, Portugal
1 shared publication - Inês Venâncio
PICadvanced S.A.
1 shared publication - Inês Venâncio1 shared publication
- Maria João Carvalhais
Instituto de Telecomunicações, 3810-193 Aveiro, Portugal
1 shared publication
Latest Publications
- Open Access
- 11 September 2024
- Published by IntechOpen
Impact of Process Variations on the Performance of Wavelength-Dependent Devices
One of the main factors for the rapid growth and industrialization of the integrated photonics field was the previous development by the microelectronics sector of lithography tools and processes for complementary metal oxide semiconductor fabrication, now also employed in the fabrication of photonic integrated circuits. However, the scarce range of methods to fine-tune photonic devices during the lithographic process results in a disparity between designed and manufactured devices. For the current state of lithographic resolution, when considering wavelength-dependent devices, such as Bragg gratings, this disparity can significantly alter the design of the component and impact its performance, as the response strongly depends on its geometry. Thus, understanding the impact of lithography in a photonic component is extremely important to minimize these variations and optimize the design process. This chapter explores the impact of manufacturing process variations, studying their effect on device geometry through a case study on contra-directional couplers, toward ultimately reducing the existing gap between designers and foundries.
- 11 September 2024
- Published by IntechOpen
Open AccessImpact of Process Variations on the Performance of Wavelength-Dependent Devices
One of the main factors for the rapid growth and industrialization of the integrated photonics field was the previous development by the microelectronics sector of lithography tools and processes for complementary metal oxide semiconductor fabrication, now also employed in the fabrication of photonic integrated circuits. However, the scarce range of methods to fine-tune photonic devices during the lithographic process results in a disparity between designed and manufactured devices. For the current state of lithographic resolution, when considering wavelength-dependent devices, such as Bragg gratings, this disparity can significantly alter the design of the component and impact its performance, as the response strongly depends on its geometry. Thus, understanding the impact of lithography in a photonic component is extremely important to minimize these variations and optimize the design process. This chapter explores the impact of manufacturing process variations, studying their effect on device geometry through a case study on contra-directional couplers, toward ultimately reducing the existing gap between designers and foundries.
- Open Access
Prediction through Simulation-Based Corrective Models of Contra-Directional Couplers’ Experimental Results
Lithography variation presents one of the biggest challenges for photonic component optimization, especially for fabless designers. Lithography prediction models are a crucial tool for minimizing the necessary number of fabrication iterations for a device’s optimization. This paper presents one of these models specifically adapted for the contra-directional coupler structure. Through the experimental characterization of devices with a specific range of design parameters, it was possible to observe how the lithography process impacts their performance. A correction model based on effective refractive index variation and its impact on the Bragg condition of the structure was developed to predict the performance variation of a device based on the expected design variation induced by fabrication. The contra-directional couplers fabricated at CORNERSTONE foundry show a tendency to be redshifted as the gap decreases, due to an increase in waveguide width as a result of a diffraction-limited lithography process. Based on these and other findings, it was possible to correlate the design parameters to the posterior fabricated structure and ultimately predict the expected experimental response.
Open AccessPrediction through Simulation-Based Corrective Models of Contra-Directional Couplers’ Experimental Results
Lithography variation presents one of the biggest challenges for photonic component optimization, especially for fabless designers. Lithography prediction models are a crucial tool for minimizing the necessary number of fabrication iterations for a device’s optimization. This paper presents one of these models specifically adapted for the contra-directional coupler structure. Through the experimental characterization of devices with a specific range of design parameters, it was possible to observe how the lithography process impacts their performance. A correction model based on effective refractive index variation and its impact on the Bragg condition of the structure was developed to predict the performance variation of a device based on the expected design variation induced by fabrication. The contra-directional couplers fabricated at CORNERSTONE foundry show a tendency to be redshifted as the gap decreases, due to an increase in waveguide width as a result of a diffraction-limited lithography process. Based on these and other findings, it was possible to correlate the design parameters to the posterior fabricated structure and ultimately predict the expected experimental response.