Hadel Obaidi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hadel Obaidi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Amjad Hamad Albayati
Univ. of Baghdad
1 shared publication - Atif Ali Hasan
Department of Mechanical Power Technical, Institute of Technology/ Baghdad, Middle Technical University, Iraq
1 shared publication Hussein K. Mohammad
1 shared publication- Mahmood Hussain Khaleel
Department of Mechanical Power Technical, Kirkuk Technical Institute Northern Technical University Kirkuk Iraq
1 shared publication - Omer Adil Zainal
Mechanical Engineering Department, College of Engineering, University of Kirkuk, Kirkuk, Iraq
1 shared publication
Latest Publications
- 1 March 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (3) , 1050-1070
Synergistic Effects of Nano Titanium Dioxide and Nano Zinc Oxide on the Physical and Rheological Properties of Asphalt Binder
Enhancing asphalt binder performance against anticipated distresses is a critical focus in pavement engineering. This study investigates the synergistic influence of nano titanium dioxide (NT) and nano zinc oxide (NZ) on asphalt binder performance. Nine NT:NZ combinations (1:1 to 3:3) were prepared with 1–3% by binder weight, in addition to a reference binder (RB). The performance test program included; conventional tests (penetration, softening point, viscosity, and ductility), Dynamic Shear Rheometer (DSR) for performance grading, Multiple Stress Creep Recovery (MSCR) for rutting evaluation, and Linear Amplitude Sweep (LAS) for fatigue resistance. Furthermore, Statistical analysis (ANOVA) was performed to determine the significance of nanomaterial interactions, and a cost–performance evaluation assessed economic feasibility. The results revealed that the combined use of these types of NM increased binder stiffness and resistance to aging. Additionally, the high-temperature PG grade increased from 70°C to 76°C for all NM-modified asphalt binders, except for the combinations of 1% NT and 1% NZ, as well as the (1:2) binder. On the other hand, MSCR results showed a reduction of up to 32% in non-recoverable creep compliance (Jnr3.2), whereas the LAS test verified extended fatigue life at a 2.5% strain level for low dosages of the NM combination, i.e., (1:1). The 1:1 NT:NZ blend exhibited the highest cost–performance efficiency, providing a balanced improvement in rutting and fatigue resistance. Overall, the synergistic incorporation of NT and NZ significantly enhanced the binder performance, offering practical insights for selecting nanomaterials in sustainable pavement engineering.
- 1 March 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (3) , 1050-1070
Synergistic Effects of Nano Titanium Dioxide and Nano Zinc Oxide on the Physical and Rheological Properties of Asphalt Binder
Enhancing asphalt binder performance against anticipated distresses is a critical focus in pavement engineering. This study investigates the synergistic influence of nano titanium dioxide (NT) and nano zinc oxide (NZ) on asphalt binder performance. Nine NT:NZ combinations (1:1 to 3:3) were prepared with 1–3% by binder weight, in addition to a reference binder (RB). The performance test program included; conventional tests (penetration, softening point, viscosity, and ductility), Dynamic Shear Rheometer (DSR) for performance grading, Multiple Stress Creep Recovery (MSCR) for rutting evaluation, and Linear Amplitude Sweep (LAS) for fatigue resistance. Furthermore, Statistical analysis (ANOVA) was performed to determine the significance of nanomaterial interactions, and a cost–performance evaluation assessed economic feasibility. The results revealed that the combined use of these types of NM increased binder stiffness and resistance to aging. Additionally, the high-temperature PG grade increased from 70°C to 76°C for all NM-modified asphalt binders, except for the combinations of 1% NT and 1% NZ, as well as the (1:2) binder. On the other hand, MSCR results showed a reduction of up to 32% in non-recoverable creep compliance (Jnr3.2), whereas the LAS test verified extended fatigue life at a 2.5% strain level for low dosages of the NM combination, i.e., (1:1). The 1:1 NT:NZ blend exhibited the highest cost–performance efficiency, providing a balanced improvement in rutting and fatigue resistance. Overall, the synergistic incorporation of NT and NZ significantly enhanced the binder performance, offering practical insights for selecting nanomaterials in sustainable pavement engineering.
- Open Access
- 6 March 2025
- Published by Akademiai Kiado Zrt. in International Review of Applied Sciences and Engineering
- Vol. 16 (1) , 60-69
Improving the building's thermal performance by using untraditional building blocks
Iraqi buildings consume high-level electrical energy for air conditioning purposes to provide the standard human comfort condition. This paper adopted an experimental study by using Styrofoam adhesive or white cement as an alternative to ordinary Portland cement to manufacture building blocks with dimensions of 200 × 200 × 200 mm containing an internal core with dimensions of 90 × 130 × 130 mm, which were filled by using corrugated scratch-up or closed air gap. The samples were divided into two sets: the first had an aluminium foil layer applied to the external surface of the samples (reflective surface), while the second was without any layer (ordinary surface). The samples were tested under the climatic conditions of Baghdad city during the summer months (May to September) of 2021. These blocks were also evaluated by different structural tests. It can be seen from the test results that the use of Styrofoam adhesive with a reflective surface with panels of corrugated scratch-up increased the thermal insulation of the wall. It leads to reduce thermal leakage and the electrical energy consumed to provide comfortable thermal conditions by 52.7%, in addition to decreasing the mass density by 14.1% while compressive strength decreased by 21%.
- 6 March 2025
- Published by Akademiai Kiado Zrt. in International Review of Applied Sciences and Engineering
- Vol. 16 (1) , 60-69
Open AccessImproving the building's thermal performance by using untraditional building blocks
Iraqi buildings consume high-level electrical energy for air conditioning purposes to provide the standard human comfort condition. This paper adopted an experimental study by using Styrofoam adhesive or white cement as an alternative to ordinary Portland cement to manufacture building blocks with dimensions of 200 × 200 × 200 mm containing an internal core with dimensions of 90 × 130 × 130 mm, which were filled by using corrugated scratch-up or closed air gap. The samples were divided into two sets: the first had an aluminium foil layer applied to the external surface of the samples (reflective surface), while the second was without any layer (ordinary surface). The samples were tested under the climatic conditions of Baghdad city during the summer months (May to September) of 2021. These blocks were also evaluated by different structural tests. It can be seen from the test results that the use of Styrofoam adhesive with a reflective surface with panels of corrugated scratch-up increased the thermal insulation of the wall. It leads to reduce thermal leakage and the electrical energy consumed to provide comfortable thermal conditions by 52.7%, in addition to decreasing the mass density by 14.1% while compressive strength decreased by 21%.