Iryna Dzhavadova
Research Subjects
Iryna Dzhavadova has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Sergey Romualdovich Ignatovich
National University "Kyiv Aviation Institute
6 shared publications - Sviatoslav Yutskevych
National University “Kyiv Aviation Institute
3 shared publications - Oleksandr Semenets
«ANTONOV» JSC, Kyiv
1 shared publication
Latest Publications
- Open Access
- 3 September 2026
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 129-135
ПОРОГОВІ ЗНАЧЕННЯ НАПРАЦЮВАННЯ АВІАЦІЙНИХ ПАНЕЛЬНИХ КОНСТРУКЦІЙ З ВТОМНИМИ ТРІЩИНАМИ
The article considers the problem of determining the threshold values for the service life of aircraft panel structures with fatigue cracks in accordance with the damage-tolerance concept. The relevance of the study stems from the need to improve the safety and efficiency of aircraft operation by reasonably predicting the residual life of defective structures and optimizing technical inspection intervals. Existing regulatory approaches to determining the safe-life and periodicity of control are based mainly on the use of dispersion coefficients, which often leads either to an excessive reduction in the structural life or to an unjustified increase in maintenance costs. The aim of the work is to develop an approach to justifying safe inspection intervals for aircraft panel structures considering the random growth of fatigue cracks and determining the threshold values for residual life. To achieve this goal, methods of fracture mechanics and statistical modeling were used. The Paris law was applied to describe the growth rate of a fatigue crack. In this case, the random nature of the parameter m of this law was considered, the distribution of which for structural aluminum alloys was assumed to be logarithmically normal. The modeling was performed on a panel structure of an aircraft fuselage skin with a central crack under different levels of cyclic stress. For each scenario of the numerical experiment, random values of the parameter m were generated, after which the residual resource of the structure was determined until the critical crack size was reached. As a result of the studies conducted, it was established that the residual resource of panel structures with fatigue cracks is satisfactorily described by the Pareto distribution. The existence of a threshold value of operation was revealed, below which the destruction of the structure does not occur regardless of the random values of the crack growth parameter. The dependence of the residual resource threshold on the magnitude of the acting stresses was determined; in semi-logarithmic coordinates, it is linear, similar to classical fatigue curves. It is shown that the use of the threshold value of the residual resource as a criterion for assigning inspection intervals allows to increase safe intervals of technical control in comparison with traditional methods based on dispersion coefficients. The results obtained can be used to develop maintenance programs and assess the residual durability of fail-safe aircraft structures. The proposed approach contributes to increasing the operational efficiency of aircraft by optimizing inspection intervals without reducing flight safety
- 3 September 2026
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 129-135
Open AccessПОРОГОВІ ЗНАЧЕННЯ НАПРАЦЮВАННЯ АВІАЦІЙНИХ ПАНЕЛЬНИХ КОНСТРУКЦІЙ З ВТОМНИМИ ТРІЩИНАМИ
The article considers the problem of determining the threshold values for the service life of aircraft panel structures with fatigue cracks in accordance with the damage-tolerance concept. The relevance of the study stems from the need to improve the safety and efficiency of aircraft operation by reasonably predicting the residual life of defective structures and optimizing technical inspection intervals. Existing regulatory approaches to determining the safe-life and periodicity of control are based mainly on the use of dispersion coefficients, which often leads either to an excessive reduction in the structural life or to an unjustified increase in maintenance costs. The aim of the work is to develop an approach to justifying safe inspection intervals for aircraft panel structures considering the random growth of fatigue cracks and determining the threshold values for residual life. To achieve this goal, methods of fracture mechanics and statistical modeling were used. The Paris law was applied to describe the growth rate of a fatigue crack. In this case, the random nature of the parameter m of this law was considered, the distribution of which for structural aluminum alloys was assumed to be logarithmically normal. The modeling was performed on a panel structure of an aircraft fuselage skin with a central crack under different levels of cyclic stress. For each scenario of the numerical experiment, random values of the parameter m were generated, after which the residual resource of the structure was determined until the critical crack size was reached. As a result of the studies conducted, it was established that the residual resource of panel structures with fatigue cracks is satisfactorily described by the Pareto distribution. The existence of a threshold value of operation was revealed, below which the destruction of the structure does not occur regardless of the random values of the crack growth parameter. The dependence of the residual resource threshold on the magnitude of the acting stresses was determined; in semi-logarithmic coordinates, it is linear, similar to classical fatigue curves. It is shown that the use of the threshold value of the residual resource as a criterion for assigning inspection intervals allows to increase safe intervals of technical control in comparison with traditional methods based on dispersion coefficients. The results obtained can be used to develop maintenance programs and assess the residual durability of fail-safe aircraft structures. The proposed approach contributes to increasing the operational efficiency of aircraft by optimizing inspection intervals without reducing flight safety
- 3 September 2026
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 129-135
ПОРОГОВІ ЗНАЧЕННЯ НАПРАЦЮВАННЯ АВІАЦІЙНИХ ПАНЕЛЬНИХ КОНСТРУКЦІЙ З ВТОМНИМИ ТРІЩИНАМИ
The article considers the problem of determining the threshold values for the service life of aircraft panel structures with fatigue cracks in accordance with the damage-tolerance concept. The relevance of the study stems from the need to improve the safety and efficiency of aircraft operation by reasonably predicting the residual life of defective structures and optimizing technical inspection intervals. Existing regulatory approaches to determining the safe-life and periodicity of control are based mainly on the use of dispersion coefficients, which often leads either to an excessive reduction in the structural life or to an unjustified increase in maintenance costs. The aim of the work is to develop an approach to justifying safe inspection intervals for aircraft panel structures considering the random growth of fatigue cracks and determining the threshold values for residual life. To achieve this goal, methods of fracture mechanics and statistical modeling were used. The Paris law was applied to describe the growth rate of a fatigue crack. In this case, the random nature of the parameter m of this law was considered, the distribution of which for structural aluminum alloys was assumed to be logarithmically normal. The modeling was performed on a panel structure of an aircraft fuselage skin with a central crack under different levels of cyclic stress. For each scenario of the numerical experiment, random values of the parameter m were generated, after which the residual resource of the structure was determined until the critical crack size was reached. As a result of the studies conducted, it was established that the residual resource of panel structures with fatigue cracks is satisfactorily described by the Pareto distribution. The existence of a threshold value of operation was revealed, below which the destruction of the structure does not occur regardless of the random values of the crack growth parameter. The dependence of the residual resource threshold on the magnitude of the acting stresses was determined; in semi-logarithmic coordinates, it is linear, similar to classical fatigue curves. It is shown that the use of the threshold value of the residual resource as a criterion for assigning inspection intervals allows to increase safe intervals of technical control in comparison with traditional methods based on dispersion coefficients. The results obtained can be used to develop maintenance programs and assess the residual durability of fail-safe aircraft structures. The proposed approach contributes to increasing the operational efficiency of aircraft by optimizing inspection intervals without reducing flight safety
- 3 September 2026
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 129-135
ПОРОГОВІ ЗНАЧЕННЯ НАПРАЦЮВАННЯ АВІАЦІЙНИХ ПАНЕЛЬНИХ КОНСТРУКЦІЙ З ВТОМНИМИ ТРІЩИНАМИ
The article considers the problem of determining the threshold values for the service life of aircraft panel structures with fatigue cracks in accordance with the damage-tolerance concept. The relevance of the study stems from the need to improve the safety and efficiency of aircraft operation by reasonably predicting the residual life of defective structures and optimizing technical inspection intervals. Existing regulatory approaches to determining the safe-life and periodicity of control are based mainly on the use of dispersion coefficients, which often leads either to an excessive reduction in the structural life or to an unjustified increase in maintenance costs. The aim of the work is to develop an approach to justifying safe inspection intervals for aircraft panel structures considering the random growth of fatigue cracks and determining the threshold values for residual life. To achieve this goal, methods of fracture mechanics and statistical modeling were used. The Paris law was applied to describe the growth rate of a fatigue crack. In this case, the random nature of the parameter m of this law was considered, the distribution of which for structural aluminum alloys was assumed to be logarithmically normal. The modeling was performed on a panel structure of an aircraft fuselage skin with a central crack under different levels of cyclic stress. For each scenario of the numerical experiment, random values of the parameter m were generated, after which the residual resource of the structure was determined until the critical crack size was reached. As a result of the studies conducted, it was established that the residual resource of panel structures with fatigue cracks is satisfactorily described by the Pareto distribution. The existence of a threshold value of operation was revealed, below which the destruction of the structure does not occur regardless of the random values of the crack growth parameter. The dependence of the residual resource threshold on the magnitude of the acting stresses was determined; in semi-logarithmic coordinates, it is linear, similar to classical fatigue curves. It is shown that the use of the threshold value of the residual resource as a criterion for assigning inspection intervals allows to increase safe intervals of technical control in comparison with traditional methods based on dispersion coefficients. The results obtained can be used to develop maintenance programs and assess the residual durability of fail-safe aircraft structures. The proposed approach contributes to increasing the operational efficiency of aircraft by optimizing inspection intervals without reducing flight safety
- Open Access
- 26 August 2026
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4,p. 21-33
ПІДХОДИ ДО ВИЗНАЧЕННЯ ПЛАСТИЧНОЇ ЗОНИ У ВЕРШИНІ ВТОМНОЇ ТРІЩИНИ ПРИ РОЗРАХУНКАХ ДОВГОВІЧНОСТІ
This paper reviews the primary approaches to assessing the plastic zone formed in the vicinity of a fatigue crack tip, and analyses how this is considered in fatigue life calculations for aircraft structures. This topic is relevant because most airframe components experience high-cycle, variable-amplitude loading, and the presence of cracks or stress concentrators can induce local plastic deformation even at relatively low nominal stress levels. Within the framework of linear elastic fracture mechanics (LEFM), stresses exhibit a singularity at the crack tip; that is, they increase infinitely as the crack tip is approached. In real structural materials, however, such an increase is limited by reaching the yield strength, resulting in the formation of a plastic zone. The size and shape of this zone affect the validity of applying LEFM parameters. The paper analyzes the stress state near the crack tip, the role of the stress intensity factor (SIF), and the conditions for the onset of plastic deformation according to the Mises and Tresca criteria. It also considers the differences between plane stress and plane strain states. Particular focus is given to the classical analytical models of Irwin, Leonov–Panasyuk–Dugdale and their modifications. The analysis includes experimental and numerical methods for refining the plastic zone, such as microhardness measurements, metallographic etching, digital image correlation (DIC), and the finite element method (FEM). The influence of the plastic zone on fatigue crack growth is considered, including the distinction between monotonic and cyclic plastic zones, plasticity-induced crack closure, and the effects of overload, underload, and load interaction in a loading spectrum. Approaches that account for the effects of local plastic deformation both at the crack tip and in the crack wake are critically evaluated, including the Wheeler, Willenborg, Generalized Willenborg, Modified Generalized Willenborg, Hsu, FASTRAN and strip-yield models. The inclusion of the plastic zone in regulatory and reference documents is also discussed. It is demonstrated that the Irwin plastic zone correction method is the most widely used approach in engineering practice for accounting for the plastic zone. It is also established that plastic zone assessment is an important component of analysing the fatigue life and residual strength of aircraft structures. This makes it possible to determine the limits of LEFM applicability, justify the selection of appropriate calculation model, account for the influence of load history and improve the reliability of durability prediction for cracked structural elements.
- 26 August 2026
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4,p. 21-33
Open AccessПІДХОДИ ДО ВИЗНАЧЕННЯ ПЛАСТИЧНОЇ ЗОНИ У ВЕРШИНІ ВТОМНОЇ ТРІЩИНИ ПРИ РОЗРАХУНКАХ ДОВГОВІЧНОСТІ
This paper reviews the primary approaches to assessing the plastic zone formed in the vicinity of a fatigue crack tip, and analyses how this is considered in fatigue life calculations for aircraft structures. This topic is relevant because most airframe components experience high-cycle, variable-amplitude loading, and the presence of cracks or stress concentrators can induce local plastic deformation even at relatively low nominal stress levels. Within the framework of linear elastic fracture mechanics (LEFM), stresses exhibit a singularity at the crack tip; that is, they increase infinitely as the crack tip is approached. In real structural materials, however, such an increase is limited by reaching the yield strength, resulting in the formation of a plastic zone. The size and shape of this zone affect the validity of applying LEFM parameters. The paper analyzes the stress state near the crack tip, the role of the stress intensity factor (SIF), and the conditions for the onset of plastic deformation according to the Mises and Tresca criteria. It also considers the differences between plane stress and plane strain states. Particular focus is given to the classical analytical models of Irwin, Leonov–Panasyuk–Dugdale and their modifications. The analysis includes experimental and numerical methods for refining the plastic zone, such as microhardness measurements, metallographic etching, digital image correlation (DIC), and the finite element method (FEM). The influence of the plastic zone on fatigue crack growth is considered, including the distinction between monotonic and cyclic plastic zones, plasticity-induced crack closure, and the effects of overload, underload, and load interaction in a loading spectrum. Approaches that account for the effects of local plastic deformation both at the crack tip and in the crack wake are critically evaluated, including the Wheeler, Willenborg, Generalized Willenborg, Modified Generalized Willenborg, Hsu, FASTRAN and strip-yield models. The inclusion of the plastic zone in regulatory and reference documents is also discussed. It is demonstrated that the Irwin plastic zone correction method is the most widely used approach in engineering practice for accounting for the plastic zone. It is also established that plastic zone assessment is an important component of analysing the fatigue life and residual strength of aircraft structures. This makes it possible to determine the limits of LEFM applicability, justify the selection of appropriate calculation model, account for the influence of load history and improve the reliability of durability prediction for cracked structural elements.
- Open Access
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 132-138
Вплив варіацій пружних характеристик матеріалу на розрахункові характеристики напружено-деформованого стану конструкції
Aluminium alloys are key materials in the aerospace industry because of their combination of low density, high specific strength, and excellent corrosion resistance. Metals are generally considered isotropic materials, exhibiting uniform mechanical properties in all directions. However, plastic deformation processes, such as rolling, can induce texture formation, whereby crystallographic grains align along the direction of deformation. This leads to planar anisotropy, which significantly affects the mechanical behavior of the material under service loads. This study investigates how variations in elastic properties – Young's modulus E and Poisson's ratio μ – affect the stress–strain state (SSS) of a 1163 ATB aluminium alloy sheet structure. A literature review was conducted on analyze the effect of anisotropy on the mechanical properties of specimens cut at various angles to the rolling direction. This confirmed the dependence of the elastic parameters on the orientation. This study presents laboratory test results for Poisson’s ratio in the longitudinal and transverse directions. The experimental data obtained were implemented in finite element modelling to assess the influence of anisotropy on the stress and strain distribution in typical thin-walled structural elements. Modelling was performed using a simplified geometry – a rectangular plate with boundary conditions that simulate real service loads. Nine combinations of elastic parameters were considered to evaluate the sensitivity of the calculated results to variation in these parameters. The analysis revealed that slight changes in the elastic properties can result in significant deviations in SSS, especially in the stress concentration zones. Such deviations considerably impact the assessment of the structural components’ residual strength and durability. Therefore, accounting for anisotropic behavior is critical for improving the accuracy of engineering calculations, particularly in strength and life assessment tasks. Therefore, accounting for anisotropic behavior is critically important to improve the accuracy of engineering calculations, particularly in tasks involving strength and life assessment. The obtained results are recommended for use in modelling, designing, and verifying aerospace components.
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 132-138
Open AccessВплив варіацій пружних характеристик матеріалу на розрахункові характеристики напружено-деформованого стану конструкції
Aluminium alloys are key materials in the aerospace industry because of their combination of low density, high specific strength, and excellent corrosion resistance. Metals are generally considered isotropic materials, exhibiting uniform mechanical properties in all directions. However, plastic deformation processes, such as rolling, can induce texture formation, whereby crystallographic grains align along the direction of deformation. This leads to planar anisotropy, which significantly affects the mechanical behavior of the material under service loads. This study investigates how variations in elastic properties – Young's modulus E and Poisson's ratio μ – affect the stress–strain state (SSS) of a 1163 ATB aluminium alloy sheet structure. A literature review was conducted on analyze the effect of anisotropy on the mechanical properties of specimens cut at various angles to the rolling direction. This confirmed the dependence of the elastic parameters on the orientation. This study presents laboratory test results for Poisson’s ratio in the longitudinal and transverse directions. The experimental data obtained were implemented in finite element modelling to assess the influence of anisotropy on the stress and strain distribution in typical thin-walled structural elements. Modelling was performed using a simplified geometry – a rectangular plate with boundary conditions that simulate real service loads. Nine combinations of elastic parameters were considered to evaluate the sensitivity of the calculated results to variation in these parameters. The analysis revealed that slight changes in the elastic properties can result in significant deviations in SSS, especially in the stress concentration zones. Such deviations considerably impact the assessment of the structural components’ residual strength and durability. Therefore, accounting for anisotropic behavior is critical for improving the accuracy of engineering calculations, particularly in strength and life assessment tasks. Therefore, accounting for anisotropic behavior is critically important to improve the accuracy of engineering calculations, particularly in tasks involving strength and life assessment. The obtained results are recommended for use in modelling, designing, and verifying aerospace components.
- Open Access
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4,p. 4-11
Визначення деформацій на довільно орієнтованих площадках
Strain gauge methods are widely used in the testing of specimens and elements of aircraft structures to assess the local stress-strain state (SSS) experimentally. These methods provide critical information about the SSS at specific points, which is essential for determining the structure’s strength and reliability. During full-scale strain measurements, the magnitudes and directions of strains on planes oriented at arbitrary angles must be determined. This is especially important when analyzing complex loading conditions or when the orientation of structural elements does not coincide with the coordinate system in which measurements are performed. Additional difficulties occur when an element of a strain gauge rosette fails, making it impossible to apply traditional methods for determining strain components. This paper proposes an alternative approach based on the use of three individually placed but maximally grouped strain gauges arranged at arbitrary angles relative to each other or relative to the strain rosette’s working elements. The methodology for determining strain components on arbitrarily oriented planes is described in detail, including mathematical relationships that connect the geometric arrangement of measuring elements with the resulting strain values. Experimental and numerical techniques are proposed to evaluate the SSS on arbitrary planes, particularly the finite element method (FEM), which allows for the modeling of complex deformation states and accurate calculations under real operational loads. The analysis confirmed the high accuracy of the proposed approach and demonstrated consistency between analytical solutions, experimental data, and numerical results. The use of three maximally grouped separate strain gauges significantly expands the capabilities of strain gauge measurements, making them effective even in complex cases where traditional techniques are no longer applicable. The obtained results may be useful for further development of experimental methods for evaluating the SSS and their application in the aerospace industry.
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4,p. 4-11
Open AccessВизначення деформацій на довільно орієнтованих площадках
Strain gauge methods are widely used in the testing of specimens and elements of aircraft structures to assess the local stress-strain state (SSS) experimentally. These methods provide critical information about the SSS at specific points, which is essential for determining the structure’s strength and reliability. During full-scale strain measurements, the magnitudes and directions of strains on planes oriented at arbitrary angles must be determined. This is especially important when analyzing complex loading conditions or when the orientation of structural elements does not coincide with the coordinate system in which measurements are performed. Additional difficulties occur when an element of a strain gauge rosette fails, making it impossible to apply traditional methods for determining strain components. This paper proposes an alternative approach based on the use of three individually placed but maximally grouped strain gauges arranged at arbitrary angles relative to each other or relative to the strain rosette’s working elements. The methodology for determining strain components on arbitrarily oriented planes is described in detail, including mathematical relationships that connect the geometric arrangement of measuring elements with the resulting strain values. Experimental and numerical techniques are proposed to evaluate the SSS on arbitrary planes, particularly the finite element method (FEM), which allows for the modeling of complex deformation states and accurate calculations under real operational loads. The analysis confirmed the high accuracy of the proposed approach and demonstrated consistency between analytical solutions, experimental data, and numerical results. The use of three maximally grouped separate strain gauges significantly expands the capabilities of strain gauge measurements, making them effective even in complex cases where traditional techniques are no longer applicable. The obtained results may be useful for further development of experimental methods for evaluating the SSS and their application in the aerospace industry.
- Open Access
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 69-76
Прогнозування напрацювання авіаційних панельних конструкцій при випадковій швидкості зростання втомних тріщин
The stochastic nature of fatigue crack growth rates must be considered when predicting the cyclic service life of aircraft fuselage skin structures. This study proposes a modelling approach based on the Paris power-law relationship. Analysis of empirical data from various literature sources demonstrates that a linear inverse correlation exists between the Paris law coefficients C and m for a wide range of structural aluminium alloys, wherein log C decreases as m increases. Based on this dependence, we propose a modified fatigue crack growth model that uses only one governing parameter: the exponent m. This contrasts with the conventional Paris equation, which uses two governing parameters. The crack propagation behavior is represented as random by treating m as a random variable. Numerical simulations were performed for crack growth in sheet structures under the assumption of a uniformly distributed random exponent m, and the operating stress range was calculated using actual fuselage geometry. The resulting predictions define the structural life until the critical crack length is reached, corresponding to the material’s fracture toughness. The minimum service life across all random realizations of m within the specified range provides a conservative and practical prediction metric. A parametric numerical study was carried out for multiple stress ranges to account for variable loading conditions. The shortest predicted life to critical crack growth was determined for each case, assuming a constant initial half-crack length of 0.003 m. The relationship between the minimum residual life and applied stress range exhibits a linear trend in semi-logarithmic coordinates, with a correlation coefficient equal to one.
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 69-76
Open AccessПрогнозування напрацювання авіаційних панельних конструкцій при випадковій швидкості зростання втомних тріщин
The stochastic nature of fatigue crack growth rates must be considered when predicting the cyclic service life of aircraft fuselage skin structures. This study proposes a modelling approach based on the Paris power-law relationship. Analysis of empirical data from various literature sources demonstrates that a linear inverse correlation exists between the Paris law coefficients C and m for a wide range of structural aluminium alloys, wherein log C decreases as m increases. Based on this dependence, we propose a modified fatigue crack growth model that uses only one governing parameter: the exponent m. This contrasts with the conventional Paris equation, which uses two governing parameters. The crack propagation behavior is represented as random by treating m as a random variable. Numerical simulations were performed for crack growth in sheet structures under the assumption of a uniformly distributed random exponent m, and the operating stress range was calculated using actual fuselage geometry. The resulting predictions define the structural life until the critical crack length is reached, corresponding to the material’s fracture toughness. The minimum service life across all random realizations of m within the specified range provides a conservative and practical prediction metric. A parametric numerical study was carried out for multiple stress ranges to account for variable loading conditions. The shortest predicted life to critical crack growth was determined for each case, assuming a constant initial half-crack length of 0.003 m. The relationship between the minimum residual life and applied stress range exhibits a linear trend in semi-logarithmic coordinates, with a correlation coefficient equal to one.
- Open Access
- 29 August 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4,p. 24-33
Методи визначення коефіцієнтів інтенсивності напружень у авіаційних конструкціях
During calculations for the fatigue and residual strength of aircraft structural elements, it is necessary to establish a functional relationship between the structure’s loading data, crack configuration, and one of the parameters characterizing the material’s limit state at the crack tip the stress intensity factor (SIF). This paper provides an overview of methods for determining SIFs. Three main approaches are described here: analytical, numerical, and experimental. The appropriateness of each approach is analyzed. It has been found that for full-scale aviation thin-walled structures with a supporting longitudinal-transverse load set of variable stiffness, subjected to complex external loading conditions and with contact surfaces and contact stresses present between structural elements, the determination of SIFs is significantly complicated when using analytical and/or numerical models. It has been established that experimental methods using strain gauge techniques are most suitable for such tasks, particularly the method proposed by J. W. Dally and R. J. Sanford, known in English technical literature as DST. The theoretical formulations of this approach are described, recommendations for determining the strain gauge orientation are presented, and existing modifications of the method are considered. The applicability of the strain gauge method to different types of materials (brittle and plastic) and to various specimen configurations is demonstrated. The review revealed potential problems that may arise when applying this method. The authors present their vision regarding the prospects for developing experimental methods for real-time monitoring of the conditions of aviation structures. In particular, a hybrid approach is proposed that combines the strain gauge method with the finite element method and the digital image correlation method. Three possible application methods are described depending on the tasks. In addition, the importance of integrating these methods into the overall diagnostic system for the timely detection and analysis of defects occurring during the operation of aviation structures is emphasized.
- 29 August 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4,p. 24-33
Open AccessМетоди визначення коефіцієнтів інтенсивності напружень у авіаційних конструкціях
During calculations for the fatigue and residual strength of aircraft structural elements, it is necessary to establish a functional relationship between the structure’s loading data, crack configuration, and one of the parameters characterizing the material’s limit state at the crack tip the stress intensity factor (SIF). This paper provides an overview of methods for determining SIFs. Three main approaches are described here: analytical, numerical, and experimental. The appropriateness of each approach is analyzed. It has been found that for full-scale aviation thin-walled structures with a supporting longitudinal-transverse load set of variable stiffness, subjected to complex external loading conditions and with contact surfaces and contact stresses present between structural elements, the determination of SIFs is significantly complicated when using analytical and/or numerical models. It has been established that experimental methods using strain gauge techniques are most suitable for such tasks, particularly the method proposed by J. W. Dally and R. J. Sanford, known in English technical literature as DST. The theoretical formulations of this approach are described, recommendations for determining the strain gauge orientation are presented, and existing modifications of the method are considered. The applicability of the strain gauge method to different types of materials (brittle and plastic) and to various specimen configurations is demonstrated. The review revealed potential problems that may arise when applying this method. The authors present their vision regarding the prospects for developing experimental methods for real-time monitoring of the conditions of aviation structures. In particular, a hybrid approach is proposed that combines the strain gauge method with the finite element method and the digital image correlation method. Three possible application methods are described depending on the tasks. In addition, the importance of integrating these methods into the overall diagnostic system for the timely detection and analysis of defects occurring during the operation of aviation structures is emphasized.