Zhiwen Suo
Research Subjects
Zhiwen Suo has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Binbin Li
Harbin Institute of Technology
4 shared publications - Dianguo Xu
Harbin Institute of Technology
4 shared publications - Yingzong Jiao
Harbin Institute of Technology
3 shared publications - Xiaodong Zhao
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin, China
2 shared publications - Lianzheng Ding
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin, China
1 shared publication - Linjie Han
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin 150001, China
1 shared publication
Latest Publications
- 2 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 11598-11615
Bidirectional Hybrid Isolated DC Transformer for All-DC Collection and Transmission System
Bidirectional dc transformer (DCT) is the key energy conversion equipment for all-dc collection and transmission system. Cost, efficiency, and dc fault blocking capability are important considerations that are currently difficult to address simultaneously for the existing modular multilevel converter (MMC) based DCT. In this article, a bidirectional hybrid isolated dc transformer (BHIT) as an alternative to the existing MMC based DCT is proposed. By replacing half of the submodules (SMs) by antiparalleled thyristors, the proposed BHIT can reduce 36.7% device cost, 32.5% device loss, and 64.8% total SM capacitance compared with the existing MMC based DCTs. By tailoring the trapezoidal waveforms of the thyristors, continuous dc currents are ensured without any filtering effort. In addition, an active fault current limiting control is further proposed to reduce the fault current during short-circuit faults. The detailed operational analysis, control schemes, simulation results, and scale-down prototype are provided to validate the effectiveness of proposed topology.
- 2 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 11598-11615
Bidirectional Hybrid Isolated DC Transformer for All-DC Collection and Transmission System
Bidirectional dc transformer (DCT) is the key energy conversion equipment for all-dc collection and transmission system. Cost, efficiency, and dc fault blocking capability are important considerations that are currently difficult to address simultaneously for the existing modular multilevel converter (MMC) based DCT. In this article, a bidirectional hybrid isolated dc transformer (BHIT) as an alternative to the existing MMC based DCT is proposed. By replacing half of the submodules (SMs) by antiparalleled thyristors, the proposed BHIT can reduce 36.7% device cost, 32.5% device loss, and 64.8% total SM capacitance compared with the existing MMC based DCTs. By tailoring the trapezoidal waveforms of the thyristors, continuous dc currents are ensured without any filtering effort. In addition, an active fault current limiting control is further proposed to reduce the fault current during short-circuit faults. The detailed operational analysis, control schemes, simulation results, and scale-down prototype are provided to validate the effectiveness of proposed topology.
- 30 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1183-1197
High-Voltage DC/DC Converter Topology With Active Filtering Arms
The rapid growth of renewable energy installation promotes the development of high voltage direct current (HVdc) links for energy integration and transmission. To meet the future needs of HVdc grids, high-voltage dc–dc converters are needed to interconnect HVdc links with different voltage levels. This article proposes a high-voltage active filtering dc–dc converter composed of only one energy buffering arm to transfer energy and two active filtering arms for dc current continuity. This topology features low cost and small footprint. The circuit configuration, operation principle, parameter design, and control strategies are presented. Particularly, the decoupling control is proposed to solve the coupling among energy balance control of different arms. Both the simulation case of 100 MW, 200 kV/320 kV, and downscaled experimental results of 1.5 kW, 150 V/300 V are provided to demonstrate the validity of the proposed topology. Furthermore, a series of dc–dc topologies with active filtering principle are derived and evaluated.
- 30 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1183-1197
High-Voltage DC/DC Converter Topology With Active Filtering Arms
The rapid growth of renewable energy installation promotes the development of high voltage direct current (HVdc) links for energy integration and transmission. To meet the future needs of HVdc grids, high-voltage dc–dc converters are needed to interconnect HVdc links with different voltage levels. This article proposes a high-voltage active filtering dc–dc converter composed of only one energy buffering arm to transfer energy and two active filtering arms for dc current continuity. This topology features low cost and small footprint. The circuit configuration, operation principle, parameter design, and control strategies are presented. Particularly, the decoupling control is proposed to solve the coupling among energy balance control of different arms. Both the simulation case of 100 MW, 200 kV/320 kV, and downscaled experimental results of 1.5 kW, 150 V/300 V are provided to demonstrate the validity of the proposed topology. Furthermore, a series of dc–dc topologies with active filtering principle are derived and evaluated.
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 12091-12095
DC/DC Converter With High Current Capability for All DC Renewable System
High current, efficiency, and compactness are the key challenges of dc/dc converters for all dc renewable system. In this letter, a dc/dc converters is proposed to address these challenges. The proposed converter incorporates three key innovations: parallel operation, direct transmission of partial power, and non-ac energy balancing. Through parallel operation, the converter facilitates the sharing of current across multiple strings of submodules, resulting in high current capability. Furthermore, the integration of direct transmission of partial power and non-ac energy balancing minimize installations of insulated gate bipolar transistors (IGBTs) and capacitors, contributes to enhanced efficiency and compactness. The effectiveness and validity of the proposed converter are demonstrated through simulation and experimental results.
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 12091-12095
DC/DC Converter With High Current Capability for All DC Renewable System
High current, efficiency, and compactness are the key challenges of dc/dc converters for all dc renewable system. In this letter, a dc/dc converters is proposed to address these challenges. The proposed converter incorporates three key innovations: parallel operation, direct transmission of partial power, and non-ac energy balancing. Through parallel operation, the converter facilitates the sharing of current across multiple strings of submodules, resulting in high current capability. Furthermore, the integration of direct transmission of partial power and non-ac energy balancing minimize installations of insulated gate bipolar transistors (IGBTs) and capacitors, contributes to enhanced efficiency and compactness. The effectiveness and validity of the proposed converter are demonstrated through simulation and experimental results.
- Open Access
- 15 November 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (22) , 11607
A Three-Port Power Electronic Transformer Based on Magnetic Integration
This paper proposes a three-port power electronic transformer (PET) based on magnetic integration, where the modular multilevel converter (MMC) arm inductors and high-frequency transformer are integrated; thus, the low-voltage DC (LVDC) port can be directly obtained. Such a magnetic integration structure has advantages of reduction in magnetic volume and number of active switches, implying a compact structure and reduced cost. Compared with existing PETs, the proposed PET can save more than 60% of magnetic volume and more than 19% of device cost. The proposed PET is suitable for AC/DC hybrid distribution applications with medium-voltage DC (MVDC), medium-voltage AC (MVAC), and LVDC ports, especially for scenarios where moderate amounts of power (100 s of kW) are tapped from an LVDC port. The feasibility of the proposed three-port PET has been verified by simulation and experimental results.
- 15 November 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (22) , 11607
Open AccessA Three-Port Power Electronic Transformer Based on Magnetic Integration
This paper proposes a three-port power electronic transformer (PET) based on magnetic integration, where the modular multilevel converter (MMC) arm inductors and high-frequency transformer are integrated; thus, the low-voltage DC (LVDC) port can be directly obtained. Such a magnetic integration structure has advantages of reduction in magnetic volume and number of active switches, implying a compact structure and reduced cost. Compared with existing PETs, the proposed PET can save more than 60% of magnetic volume and more than 19% of device cost. The proposed PET is suitable for AC/DC hybrid distribution applications with medium-voltage DC (MVDC), medium-voltage AC (MVAC), and LVDC ports, especially for scenarios where moderate amounts of power (100 s of kW) are tapped from an LVDC port. The feasibility of the proposed three-port PET has been verified by simulation and experimental results.