Seong-Won Jo
Research Subjects
Seong-Won Jo has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Gul Rahim
Daejeon Research and Development Center, Autosilicon Company Ltd., Daejeon, South Korea
2 shared publications - Kyeongha Kwon
School of Electrical Engineering, Korea Advanced Institute of Science and Technology, Daejeon, Republic of Korea
2 shared publications - Sang-Gug Lee
School of Electrical Engineering, Korea Advanced Institute of Science and Technology, Daejeon, South Korea
2 shared publications - Young-Nam Lee
Daejeon Research and Development Center, Autosilicon Company Ltd., Daejeon, South Korea
2 shared publications - Jeongwon Han
Korea Advanced Institute of Science and Technology (KAIST)
1 shared publication - Kyung-Sik Choi
Yonsei University
1 shared publication
Latest Publications
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 9523112
Fast and Accurate Lithium-Ion Battery Impedance Measurement Using Multirate Quadrature Demodulation With Bandpass Filtering
Electrochemical impedance spectroscopy (EIS) is a noninvasive tool for characterizing battery states based on impedance across a specific frequency range. High-capacity lithium-ion batteries in electric vehicles demands impedance measurements within a sub-mΩ resolution. While EIS systems widely adopt quadrature demodulation for its accuracy, it suffers from long settling time and high hardware complexity, limiting integration feasibility. This work presents a novel multi-rate quadrature demodulation scheme with complex band-pass filtering that simultaneously reduces measurement time and implementation costs while maintaining high precision. The proposed EIS system employs multiple spur suppression stages where complex band-pass filters (BPFs) suppress DC offset and image tones, enabling subsequent low-pass filters (LPFs) to operate with wider cut-off frequency. Multi-rate signal processing using two distinct decimation stages enables adaptive LPF control, optimizing settling time across 100m-to-1k Hz frequency range. Compared to multi-rate architecture without complex BPF, the proposed approach achieves a 66% and 67% reduction in the impedance measurement time over the frequency range of 100m-to-1k Hz and at the lower bound (100 mHz), respectively. Compared to prior single-rate architectures requiring multiple LPF pairs, this approach achieves 32% faster measurement over the overlapping frequency range of 1-to-1k Hz while requiring 26% fewer hardware resources (ALUTs, registers, and DSPs) through a single BPF coefficient set and single infinite-impulse response LPF pair to cover the entire frequency range. Measurement repeatability shows standard deviation below 1.6 μΩ for known resistors (100 μΩ and 1 mΩ). The system is compared with a commercial electrochemical workstation for a high-capacity battery (70 Ah) across a 20-80% state-of-charge range at 0-45°C temperature.
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 9523112
Fast and Accurate Lithium-Ion Battery Impedance Measurement Using Multirate Quadrature Demodulation With Bandpass Filtering
Electrochemical impedance spectroscopy (EIS) is a noninvasive tool for characterizing battery states based on impedance across a specific frequency range. High-capacity lithium-ion batteries in electric vehicles demands impedance measurements within a sub-mΩ resolution. While EIS systems widely adopt quadrature demodulation for its accuracy, it suffers from long settling time and high hardware complexity, limiting integration feasibility. This work presents a novel multi-rate quadrature demodulation scheme with complex band-pass filtering that simultaneously reduces measurement time and implementation costs while maintaining high precision. The proposed EIS system employs multiple spur suppression stages where complex band-pass filters (BPFs) suppress DC offset and image tones, enabling subsequent low-pass filters (LPFs) to operate with wider cut-off frequency. Multi-rate signal processing using two distinct decimation stages enables adaptive LPF control, optimizing settling time across 100m-to-1k Hz frequency range. Compared to multi-rate architecture without complex BPF, the proposed approach achieves a 66% and 67% reduction in the impedance measurement time over the frequency range of 100m-to-1k Hz and at the lower bound (100 mHz), respectively. Compared to prior single-rate architectures requiring multiple LPF pairs, this approach achieves 32% faster measurement over the overlapping frequency range of 1-to-1k Hz while requiring 26% fewer hardware resources (ALUTs, registers, and DSPs) through a single BPF coefficient set and single infinite-impulse response LPF pair to cover the entire frequency range. Measurement repeatability shows standard deviation below 1.6 μΩ for known resistors (100 μΩ and 1 mΩ). The system is compared with a commercial electrochemical workstation for a high-capacity battery (70 Ah) across a 20-80% state-of-charge range at 0-45°C temperature.
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (3) , 3202-3212
Small-Perturbation Electrochemical Impedance Spectroscopy System With High Accuracy for High-Capacity Batteries in Electric Vehicles
This article presents an electrochemical impedance spectroscopy (EIS) system optimized for high-capacity electric vehicle (EV) batteries, prioritizing high measurement accuracy with minimal current perturbation while reducing measurement time. The system incorporates a switched-resistor high-pass filter for accurate ac voltage measurement and a low-noise amplifier for signal amplification. It also features two parallel low-pass filters with tailored bandwidths (0.2 Hz for 1–9 Hz and 1 Hz for 10–1 k Hz), significantly enhancing accuracy and reducing settling time. In addition, the small current perturbation approach improves safety and simplifies the analysis process. Our prototype achieves precise impedance measurement with a standard deviation of less than 10.4 $\boldsymbol{\mu}\boldsymbol{\Omega}$ for high-precision resistors and less than 14 $\boldsymbol{\mu}\boldsymbol{\Omega}$ root-mean-square error in magnitude for a 70 Ah battery across 1–1 k Hz frequency range and 20–80% state-of-charge range at 25${}^{\circ}\text{C}$ temperature. These findings demonstrate the proposed EIS system's effectiveness in the accurate assessment and health monitoring of large EV batteries.
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (3) , 3202-3212
Small-Perturbation Electrochemical Impedance Spectroscopy System With High Accuracy for High-Capacity Batteries in Electric Vehicles
This article presents an electrochemical impedance spectroscopy (EIS) system optimized for high-capacity electric vehicle (EV) batteries, prioritizing high measurement accuracy with minimal current perturbation while reducing measurement time. The system incorporates a switched-resistor high-pass filter for accurate ac voltage measurement and a low-noise amplifier for signal amplification. It also features two parallel low-pass filters with tailored bandwidths (0.2 Hz for 1–9 Hz and 1 Hz for 10–1 k Hz), significantly enhancing accuracy and reducing settling time. In addition, the small current perturbation approach improves safety and simplifies the analysis process. Our prototype achieves precise impedance measurement with a standard deviation of less than 10.4 $\boldsymbol{\mu}\boldsymbol{\Omega}$ for high-precision resistors and less than 14 $\boldsymbol{\mu}\boldsymbol{\Omega}$ root-mean-square error in magnitude for a 70 Ah battery across 1–1 k Hz frequency range and 20–80% state-of-charge range at 25${}^{\circ}\text{C}$ temperature. These findings demonstrate the proposed EIS system's effectiveness in the accurate assessment and health monitoring of large EV batteries.