Pedro Rodríguez Sandoval
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pedro Rodríguez Sandoval has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Andres Felipe Rubiano-Navarrete
Grupo de Investigación en Diseño, Innovación y Asistencia Técnica para Materiales Avanzados-DITMAV, Doctorado en Ingeniería y Ciencia de los Materiales, Universidad Pedagógica y Tecnológica de Colombia—UPTC, Tunja 150003, Colombia
3 shared publications - Edwin Yesid Gómez-Pachón
Grupo de Investigación en Diseño, Innovación y Asistencia Técnica para Materiales Avanzados-DITMAV, Escuela de Diseño Industrial, Universidad Pedagógica y Tecnológica de Colombia—UPTC, Duitama 150461, Colombia
3 shared publications - Ricardo Vera-Graziano
Institute of Materials Research, National Autonomous University of Mexico, Mexico City 04510, Mexico, Mexico
2 shared publications - Angie Natalia Cuy Talero
Grupo de Investigación en Diseño, Innovación y Asistencia Técnica para Materiales Avanzados-DITMAV, Escuela de Diseño Industrial, Universidad Pedagógica y Tecnológica de Colombia—UPTC, Duitama 150461, Colombia
1 shared publication - Yolanda Torres-Pérez
Grupo de Investigación en Energía y Nuevas Tecnologías—GENTE, Escuela Ingeniería Electromecánica, Facultad Duitama, Universidad Pedagógica y Tecnológica de Colombia—UPTC, Duitama 150461, Colombia
1 shared publication
Latest Publications
- Open Access
Evaluation of the Biodegradability of a Composite Material Reinforced with Cellulose Acetate Nanofibers
The development of biodegradable composite materials offers a sustainable alternative to conventional synthetic polymers, particularly in short-lived applications. In this context, the incorporation of nanoscale reinforcements can improve mechanical properties without compromising the material’s degradability. The purpose of this study was to evaluate the composting behavior of a composite material based on low-density polyethylene (LDPE), potato starch, and cellulose acetate nanofibers (NFCA). The material’s degradability and mechanical stability were analyzed over 180 days according to the ASTM D5988 standard. The nanofibers were produced via electrospinning, yielding an average diameter of approximately 85 nm. The composite material was prepared using twin-screw extrusion followed by injection molding to produce ASTM D638 test specimens. The effects of biodegradation were evaluated through mass loss, CO2 generation in a desiccator, tensile testing, Shore D hardness measurements, and microstructural analysis via scanning electron microscopy (SEM). The results demonstrated a progressive increase in CO2 generation, particularly in the reinforced formulations (up to 111.76%). The formulation containing 3% NFCA exhibited the greatest mass loss (20.28%). Tensile testing revealed moderate reductions in maximum stress (1.66–8.44%), whereas hardness increased by up to 5.4% in the reinforced formulations. SEM analysis revealed increased porosity as the composting period progressed. The findings suggest that the incorporation of NFCA enhances biodegradative performance, as evidenced by increased CO2 evolution, mass loss, and morphological changes during composting.
Open AccessEvaluation of the Biodegradability of a Composite Material Reinforced with Cellulose Acetate Nanofibers
The development of biodegradable composite materials offers a sustainable alternative to conventional synthetic polymers, particularly in short-lived applications. In this context, the incorporation of nanoscale reinforcements can improve mechanical properties without compromising the material’s degradability. The purpose of this study was to evaluate the composting behavior of a composite material based on low-density polyethylene (LDPE), potato starch, and cellulose acetate nanofibers (NFCA). The material’s degradability and mechanical stability were analyzed over 180 days according to the ASTM D5988 standard. The nanofibers were produced via electrospinning, yielding an average diameter of approximately 85 nm. The composite material was prepared using twin-screw extrusion followed by injection molding to produce ASTM D638 test specimens. The effects of biodegradation were evaluated through mass loss, CO2 generation in a desiccator, tensile testing, Shore D hardness measurements, and microstructural analysis via scanning electron microscopy (SEM). The results demonstrated a progressive increase in CO2 generation, particularly in the reinforced formulations (up to 111.76%). The formulation containing 3% NFCA exhibited the greatest mass loss (20.28%). Tensile testing revealed moderate reductions in maximum stress (1.66–8.44%), whereas hardness increased by up to 5.4% in the reinforced formulations. SEM analysis revealed increased porosity as the composting period progressed. The findings suggest that the incorporation of NFCA enhances biodegradative performance, as evidenced by increased CO2 evolution, mass loss, and morphological changes during composting.
- Open Access
Effect of Fiber Loading on Green Composites of Recycled HDPE Reinforced with Banana Short Fiber: Physical, Mechanical and Morphological Properties
Currently, research on composite materials derived from natural fibers and agro-industrial waste has generated industrial proposals for producing useful materials with sufficient mechanical strength for applications involving the reuse of waste for secondary purposes. The objective of this study was to determine the influence of fiber content on the final tensile strength of the composite material, serving as a reference for the manufacture of plates. To achieve this, high-density polyethylene (HDPE) composites reinforced with short banana fibers were prepared using a blade mill and hot compression molding techniques. Two levels of short banana fiber content—10% and 20% by weight—were used, along with two types of HDPE: virgin and recycled. We evaluated the effect of adding short banana fibers on the mechanical properties of the composite, specifically tensile strength, according to the ASTM D638 standard for polymeric materials. These results were correlated with the structural properties obtained through morphological, chemical, and thermal characterization of the developed materials. The mechanical evaluation results showed that the tensile strength and elastic modulus depend on the short banana fiber content and the type of high-density polyethylene. Thermogravimetric analysis revealed that the composites decompose faster than the pure polymers (virgin and recycled HDPE). Based on these findings, the composite material prepared under optimal conditions is recommended for use in walls or construction boards where high tensile strength is not critical, due to the decreased mechanical properties resulting from the incorporation of agro-industrial waste.
Open AccessEffect of Fiber Loading on Green Composites of Recycled HDPE Reinforced with Banana Short Fiber: Physical, Mechanical and Morphological Properties
Currently, research on composite materials derived from natural fibers and agro-industrial waste has generated industrial proposals for producing useful materials with sufficient mechanical strength for applications involving the reuse of waste for secondary purposes. The objective of this study was to determine the influence of fiber content on the final tensile strength of the composite material, serving as a reference for the manufacture of plates. To achieve this, high-density polyethylene (HDPE) composites reinforced with short banana fibers were prepared using a blade mill and hot compression molding techniques. Two levels of short banana fiber content—10% and 20% by weight—were used, along with two types of HDPE: virgin and recycled. We evaluated the effect of adding short banana fibers on the mechanical properties of the composite, specifically tensile strength, according to the ASTM D638 standard for polymeric materials. These results were correlated with the structural properties obtained through morphological, chemical, and thermal characterization of the developed materials. The mechanical evaluation results showed that the tensile strength and elastic modulus depend on the short banana fiber content and the type of high-density polyethylene. Thermogravimetric analysis revealed that the composites decompose faster than the pure polymers (virgin and recycled HDPE). Based on these findings, the composite material prepared under optimal conditions is recommended for use in walls or construction boards where high tensile strength is not critical, due to the decreased mechanical properties resulting from the incorporation of agro-industrial waste.
- Open Access
Evaluation of Mechanical Properties of Composite Material with a Thermoplastic Matrix Reinforced with Cellulose Acetate Microfibers
Low-density polyethylene (LDPE) has been widely used in various applications due to its flexibility, lightness, and low production cost. However, its massive use in disposable products has raised environmental concerns, prompting the search for more sustainable alternatives. This study aims to investigate the mechanical properties achievable in a composite material utilizing low-density polyethylene (LDPE), potato starch (PS), and cellulose microfibrils (MFCA) at loadings of 0.05%, 0.15%, and 0.30%. Initially, the cellulose acetate microfibrils (MFCA) were produced via an electrospinning process. Subsequently, a dispersive mixture of the aforementioned materials was created through the extrusion and pelletizing process to form pellets. These pellets were then molded by injection molding to produce test specimens in accordance with ASTM D 638, the standard for tensile strength testing. The evaluation of the properties was conducted through mechanical tensile tests (ASTM D638), hardness tests (ASTM D 2240), melt flow index (ASTM D1238), and scanning electron microscopy (SEM). This study determined the influence of cellulose acetate microfibril loadings below 0.3% as reinforcement within a thermoplastic LDPE matrix. It was demonstrated that these microfibrils, due to their length-to-diameter ratio, contribute to an enhancement in the mechanical properties.
Open AccessEvaluation of Mechanical Properties of Composite Material with a Thermoplastic Matrix Reinforced with Cellulose Acetate Microfibers
Low-density polyethylene (LDPE) has been widely used in various applications due to its flexibility, lightness, and low production cost. However, its massive use in disposable products has raised environmental concerns, prompting the search for more sustainable alternatives. This study aims to investigate the mechanical properties achievable in a composite material utilizing low-density polyethylene (LDPE), potato starch (PS), and cellulose microfibrils (MFCA) at loadings of 0.05%, 0.15%, and 0.30%. Initially, the cellulose acetate microfibrils (MFCA) were produced via an electrospinning process. Subsequently, a dispersive mixture of the aforementioned materials was created through the extrusion and pelletizing process to form pellets. These pellets were then molded by injection molding to produce test specimens in accordance with ASTM D 638, the standard for tensile strength testing. The evaluation of the properties was conducted through mechanical tensile tests (ASTM D638), hardness tests (ASTM D 2240), melt flow index (ASTM D1238), and scanning electron microscopy (SEM). This study determined the influence of cellulose acetate microfibril loadings below 0.3% as reinforcement within a thermoplastic LDPE matrix. It was demonstrated that these microfibrils, due to their length-to-diameter ratio, contribute to an enhancement in the mechanical properties.