Takuma Saito
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Takuma Saito has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Hiroshi Harada
4 shared publications- Taisuke T. Sasaki
National Institute for Materials Science
4 shared publications Makoto Osawa
3 shared publicationsShinsuke Suzuki
3 shared publicationsTadaharu Yokokawa
3 shared publications- Hideyuki Murakami
Research Center for Structural Materials, National Institute for Materials Science, Tsukuba, Japan
2 shared publications
Latest Publications
- 16 January 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1175, 129-134
Influence of Hierarchical Structure on Mechanical Properties of Additive Manufactured IN718 Alloys
Selective laser melting (SLM) can produce Ni-based superalloys with a unique hierarchical structure consisting of micrometer-scale crystallographic lamellar microstructure and nanometer-scale cellular structure under optimized process parameters. This work investigated the effects of input energy density on the morphology of the cells and its influence on the tensile properties of Ni-based superalloy prepared by SLM. We found that the cell spacing decreases with decreasing input energy density. Further investigation of the cells clarified that the boundary of cells is a low angle grain boundary with dislocation cell wall and segregation of certain elements such as Nb and Ti. Moreover, it was demonstrated that the boundary of cells performs as a significant barrier to the griding dislocation. Thus, the cell boundary leads to strong strengthening through the Hall-Petch law.
- 16 January 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1175, 129-134
Influence of Hierarchical Structure on Mechanical Properties of Additive Manufactured IN718 Alloys
Selective laser melting (SLM) can produce Ni-based superalloys with a unique hierarchical structure consisting of micrometer-scale crystallographic lamellar microstructure and nanometer-scale cellular structure under optimized process parameters. This work investigated the effects of input energy density on the morphology of the cells and its influence on the tensile properties of Ni-based superalloy prepared by SLM. We found that the cell spacing decreases with decreasing input energy density. Further investigation of the cells clarified that the boundary of cells is a low angle grain boundary with dislocation cell wall and segregation of certain elements such as Nb and Ti. Moreover, it was demonstrated that the boundary of cells performs as a significant barrier to the griding dislocation. Thus, the cell boundary leads to strong strengthening through the Hall-Petch law.
- Open Access
- 2 November 2025
- Published by Elsevier in Acta Materialia
- Vol. 303
Effect of nanoscale cellular structure on the mechanical properties of Inconel 718 with unique hierarchical structure fabricated by laser powder bed fusion
- 2 November 2025
- Published by Elsevier in Acta Materialia
- Vol. 303
Open AccessEffect of nanoscale cellular structure on the mechanical properties of Inconel 718 with unique hierarchical structure fabricated by laser powder bed fusion
- Open Access
On the Solidification and Phase Stability of Re-Bearing High-Entropy Superalloys with Hierarchical Microstructures
This study presents the design and microstructural investigation of a single-crystal (SX) Re-bearing high-entropy superalloy (HESA-X1) featuring a thermally stable γ–γ′–γ hierarchical microstructure. The alloy exhibits FCC γ nanoparticles embedded within L12-ordered γ′ precipitates, themselves distributed in a γ matrix, with the suppression of detrimental topologically close-packed (TCP) phases. To elucidate solidification behavior and phase stability, Scheil–Gulliver and TC-PRISMA simulations were conducted alongside SEM and XRD analyses. Near-atomic scale analysis in 3D using Atom Probe Tomography (APT) revealed pronounced elemental partitioning, with Re strongly segregating to the γ matrix, while Al and Ti were preferentially enriched in the γ′ phase. Notably, Re demonstrated a unique partitioning behavior compared to conventional superalloys, facilitating the formation and stabilization of γ nanoparticles during two-step aging (Ag-2). These γ nanoparticles significantly contribute to improved mechanical properties. Long-term aging (up to 200 h) at 750–850 °C confirmed exceptional phase stability, with minimal coarsening of γ′ and retention of γ nanoparticles. The coarsening rate constant K of γ′ at 750 °C was significantly lower than that of Re-free HESA, confirming the diffusion-suppressing effect of Re. These findings highlight critical roles of Re in enhancing microstructural stability by reducing atomic mobility, enabling the development of next-generation HESAs with superior thermal and mechanical properties for high-temperature applications.
Open AccessOn the Solidification and Phase Stability of Re-Bearing High-Entropy Superalloys with Hierarchical Microstructures
This study presents the design and microstructural investigation of a single-crystal (SX) Re-bearing high-entropy superalloy (HESA-X1) featuring a thermally stable γ–γ′–γ hierarchical microstructure. The alloy exhibits FCC γ nanoparticles embedded within L12-ordered γ′ precipitates, themselves distributed in a γ matrix, with the suppression of detrimental topologically close-packed (TCP) phases. To elucidate solidification behavior and phase stability, Scheil–Gulliver and TC-PRISMA simulations were conducted alongside SEM and XRD analyses. Near-atomic scale analysis in 3D using Atom Probe Tomography (APT) revealed pronounced elemental partitioning, with Re strongly segregating to the γ matrix, while Al and Ti were preferentially enriched in the γ′ phase. Notably, Re demonstrated a unique partitioning behavior compared to conventional superalloys, facilitating the formation and stabilization of γ nanoparticles during two-step aging (Ag-2). These γ nanoparticles significantly contribute to improved mechanical properties. Long-term aging (up to 200 h) at 750–850 °C confirmed exceptional phase stability, with minimal coarsening of γ′ and retention of γ nanoparticles. The coarsening rate constant K of γ′ at 750 °C was significantly lower than that of Re-free HESA, confirming the diffusion-suppressing effect of Re. These findings highlight critical roles of Re in enhancing microstructural stability by reducing atomic mobility, enabling the development of next-generation HESAs with superior thermal and mechanical properties for high-temperature applications.
- Open Access
- 29 April 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 941
Elastic moduli of 6th generation Ni-base single crystal superalloy TMS-238 and its tie-lined γ and γ′ phases
- 29 April 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 941
Open AccessElastic moduli of 6th generation Ni-base single crystal superalloy TMS-238 and its tie-lined γ and γ′ phases
- 20 March 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1022
Effect of cobalt presence on creep properties of Ni-based single crystal superalloys at intermediate temperature
- 20 March 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1022
Effect of cobalt presence on creep properties of Ni-based single crystal superalloys at intermediate temperature
- 7 December 2024
- Published by Elsevier in Scripta Materialia
- Vol. 258
Effect of Co on twin formation and magnetic properties of Sm(Fe,Ti,V)12 alloys
- 7 December 2024
- Published by Elsevier in Scripta Materialia
- Vol. 258
Effect of Co on twin formation and magnetic properties of Sm(Fe,Ti,V)12 alloys
- Open Access
- 1 December 2024
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 65 (12) , 1443-1457
Raft Structure of Nickel Base Single-Crystal Superalloys
Series of Ni-base single-crystal superalloys with superior thermal durability have been developed to improve thermal efficiency of gas turbine systems. Microstructural transition during creep so called “raft structure” formation enhances creep properties at lower stress and higher temperature condition. Furthermore, larger perfection degree of the raft structure contributes to better creep properties under the same creep condition. To control the perfection degree of the raft structure, magnitude of a lattice misfit and an elastic misfit between γ and γ′ phases should be controlled. In the current situation, the lattice misfit can be controlled by using alloy design program NIMS has developed. In this review, we focused on the role of the raft structure in alloy design. Observation results and predicted mechanisms about strengthening by the microstructural transition, in addition to the mechanism about microstructural transition itself during creep, were summarized and explained. Finally, under these recognitions mentioned above, our effort to establish a new alloy design approach to control the perfection degree of the raft structure by modifying the elastic misfit were introduced. This Paper was Originally Published in Japanese in J. Japan Inst. Met. Mater. 86 (2022) 157–171.
- 1 December 2024
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 65 (12) , 1443-1457
Open AccessRaft Structure of Nickel Base Single-Crystal Superalloys
Series of Ni-base single-crystal superalloys with superior thermal durability have been developed to improve thermal efficiency of gas turbine systems. Microstructural transition during creep so called “raft structure” formation enhances creep properties at lower stress and higher temperature condition. Furthermore, larger perfection degree of the raft structure contributes to better creep properties under the same creep condition. To control the perfection degree of the raft structure, magnitude of a lattice misfit and an elastic misfit between γ and γ′ phases should be controlled. In the current situation, the lattice misfit can be controlled by using alloy design program NIMS has developed. In this review, we focused on the role of the raft structure in alloy design. Observation results and predicted mechanisms about strengthening by the microstructural transition, in addition to the mechanism about microstructural transition itself during creep, were summarized and explained. Finally, under these recognitions mentioned above, our effort to establish a new alloy design approach to control the perfection degree of the raft structure by modifying the elastic misfit were introduced. This Paper was Originally Published in Japanese in J. Japan Inst. Met. Mater. 86 (2022) 157–171.
- Open Access
- 6 September 2024
- Published by Elsevier in Next Materials
- Vol. 7
CALPHAD approach for prediction of local phase transformation at superlattice stacking fault in gamma prime precipitates in superalloys with multi-component system
- 6 September 2024
- Published by Elsevier in Next Materials
- Vol. 7
Open AccessCALPHAD approach for prediction of local phase transformation at superlattice stacking fault in gamma prime precipitates in superalloys with multi-component system