Pingwei Ye
Research Subjects
Pingwei Ye has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Sumin Li
School of Materials Science & Engineering, Jiangsu University, Zhenjiang 212013, China
2 shared publications - Bo Yang
State Key Laboratory of Chemistry for NBC Hazards Protection, Beijing 102205, PR China
1 shared publication - Bo Yang
State Key Laboratory of NBC Protection for Civilian, Beijing 102205, China
1 shared publication - Chuan Zhou
State Key Laboratory of NBC Protection for Civilian, Beijing 100191, China
1 shared publication - Feng Liu
School of Materials Science & Engineering, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Feng Liu
School of Materials Science & Engineering, Jiangsu University, Zhenjiang 212013, China
1 shared publication
Latest Publications
- Open Access
- 3 December 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (56) , 48440-48449
LiCl modified MOFs-derived porous carbon hollow spheres for efficient solar-driven atmospheric water harvesting
Developing adsorbents with excellent photothermal and water uptake properties for solar-driven sorption-based atmospheric water harvesting (SAWH) is full of challenging, which requires a balance between the adsorption capacity, hydrophilicity, and photothermal performance of adsorbent. In this work, a LiCl modfiied porous carbon hollow microspheres (CHM@LiCl) adsorbent with high adsorption capacity (2.07 g g−1) at 100% RH and enhanced low moisture adsorption performance was synthesized by loading LiCl hydrophilic adsorption sites into MOFs-derived hollow porous carbon. LiCl, as the main adsorption site, enhances the hydrophilicity of the CHM@LiCl adsorbent, and its water uptake capacity at 20% RH, 40% RH, 60% RH, and 80% RH are 0.25, 0.39, 0.60 and 1.04 g g−1, respectively. In addition, the hiearchical porous structure of the hollow carbon with mciroporus shell effectively suppresses the salt leakage during water adsorption. The sorbent exhibites stable performance for cycling water adsorption-release, indicating its long-term reliability. The excellent photothermal performance of CHM@LiCl adsorbent can quickly heat up to 67 °C under one sun irradiation, and completely desorb the adsorbed water within 30 minutes. The outdoor water harvesting experiment shows that the CHM@LiCl adsorbent holds great potential for practical solar-driven SAWH with a water collection capacity of 3.3 Lwater kgsorbent −1 day under RH 60%.
- 3 December 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (56) , 48440-48449
Open AccessLiCl modified MOFs-derived porous carbon hollow spheres for efficient solar-driven atmospheric water harvesting
Developing adsorbents with excellent photothermal and water uptake properties for solar-driven sorption-based atmospheric water harvesting (SAWH) is full of challenging, which requires a balance between the adsorption capacity, hydrophilicity, and photothermal performance of adsorbent. In this work, a LiCl modfiied porous carbon hollow microspheres (CHM@LiCl) adsorbent with high adsorption capacity (2.07 g g−1) at 100% RH and enhanced low moisture adsorption performance was synthesized by loading LiCl hydrophilic adsorption sites into MOFs-derived hollow porous carbon. LiCl, as the main adsorption site, enhances the hydrophilicity of the CHM@LiCl adsorbent, and its water uptake capacity at 20% RH, 40% RH, 60% RH, and 80% RH are 0.25, 0.39, 0.60 and 1.04 g g−1, respectively. In addition, the hiearchical porous structure of the hollow carbon with mciroporus shell effectively suppresses the salt leakage during water adsorption. The sorbent exhibites stable performance for cycling water adsorption-release, indicating its long-term reliability. The excellent photothermal performance of CHM@LiCl adsorbent can quickly heat up to 67 °C under one sun irradiation, and completely desorb the adsorbed water within 30 minutes. The outdoor water harvesting experiment shows that the CHM@LiCl adsorbent holds great potential for practical solar-driven SAWH with a water collection capacity of 3.3 Lwater kgsorbent −1 day under RH 60%.
- Open Access
- 4 June 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (11) , 864
Optimizing the Structure and Performances of Cu-MOF@Ti3C2TX Hybrid Electrodes by Introducing Modulated Ligand
To date, two-dimensional metal–organic frameworks (2D MOFs) have attracted much attention in many fields. Owing to their ultra-high porosity and specific surface area, great structural diversity and functional tunability, as well as feasible precision design at the molecular level, 2D MOFs have won rapid development in the field of energy storage. However, as a coordination compound, MOFs possess poor structural stability and are prone to structural collapse in electrochemical reactions, which seriously limits their electrochemical performance. Therefore, there is an urgent need to improve the structural stability of MOF electrode materials. In this study, a 2D MOF@Ti3C2TX hybrid was constructed, in which urea pyrimidinone isocyanate (UPy-NCO) units were introduced via a condensation reaction with the active functional groups on MOFs, thus forming multiple hydrogen bonds among MOF frameworks to strengthen their structural stability. Importantly, 2,6-diaminopyridine was utilized to modulate the structure and properties. Initially, the mono-coordination model of the N atom on a pyridine ring with metal ions could create defects and form further pores. Two −NH2 groups helped to improve the grafting reaction degree of UPy-NCO, leading to an increased ratio of forming quadruple hydrogen bonds (H-bonds), further strengthening the structure of the hybrid. As expected, the Cu-MOF@Ti3C2TX-20%DAP-UPy hybrid exhibited a specific capacitance of 148 F g−1 at 1 A g−1, which is 45% higher than that of Cu-MOF@Ti3C2TX-UPy (102 F g−1). A good capacitance retention of 88% was obtained as the current density increased from 0.2 to 5 A g−1. Moreover, excellent cycling stability (91.1%) was obtained at 1 A g−1 after 5000 cycles.
- 4 June 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (11) , 864
Open AccessOptimizing the Structure and Performances of Cu-MOF@Ti3C2TX Hybrid Electrodes by Introducing Modulated Ligand
To date, two-dimensional metal–organic frameworks (2D MOFs) have attracted much attention in many fields. Owing to their ultra-high porosity and specific surface area, great structural diversity and functional tunability, as well as feasible precision design at the molecular level, 2D MOFs have won rapid development in the field of energy storage. However, as a coordination compound, MOFs possess poor structural stability and are prone to structural collapse in electrochemical reactions, which seriously limits their electrochemical performance. Therefore, there is an urgent need to improve the structural stability of MOF electrode materials. In this study, a 2D MOF@Ti3C2TX hybrid was constructed, in which urea pyrimidinone isocyanate (UPy-NCO) units were introduced via a condensation reaction with the active functional groups on MOFs, thus forming multiple hydrogen bonds among MOF frameworks to strengthen their structural stability. Importantly, 2,6-diaminopyridine was utilized to modulate the structure and properties. Initially, the mono-coordination model of the N atom on a pyridine ring with metal ions could create defects and form further pores. Two −NH2 groups helped to improve the grafting reaction degree of UPy-NCO, leading to an increased ratio of forming quadruple hydrogen bonds (H-bonds), further strengthening the structure of the hybrid. As expected, the Cu-MOF@Ti3C2TX-20%DAP-UPy hybrid exhibited a specific capacitance of 148 F g−1 at 1 A g−1, which is 45% higher than that of Cu-MOF@Ti3C2TX-UPy (102 F g−1). A good capacitance retention of 88% was obtained as the current density increased from 0.2 to 5 A g−1. Moreover, excellent cycling stability (91.1%) was obtained at 1 A g−1 after 5000 cycles.
- Open Access
- 12 September 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (18) , 1482
Introducing Molecular Sieve into Activated Carbon to Achieve High-Effective Adsorption for Ethylene Oxide
Presently, ethylene oxide (EtO) is posing a significant threat to both human health and the environment due to occasional or deliberate emissions. However, few works so far have focused on this issue. It is urgent to explore novel and effective technology to protect against the threat of EtO. Herein, a series of AC/ZSM-5 composites were prepared to improve the adsorption performance for EtO, evaluated by dynamic breakthrough experiments. Particularly, the AC/ZSM-20% composite demonstrated a more excellent adsorption capacity of 81.9 mg/g at 25 °C and 50% RH than that of pristine AC and ZSM-5 with 32.5 and 52.3 mg/g, respectively. Moreover, the adsorption capacity of the AC/ZSM-20% composite remained constant even after five adsorption-desorption cycles. The adsorption mechanism of EtO on the composite is further revealed by density functional theory (DFT) calculations.
- 12 September 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (18) , 1482
Open AccessIntroducing Molecular Sieve into Activated Carbon to Achieve High-Effective Adsorption for Ethylene Oxide
Presently, ethylene oxide (EtO) is posing a significant threat to both human health and the environment due to occasional or deliberate emissions. However, few works so far have focused on this issue. It is urgent to explore novel and effective technology to protect against the threat of EtO. Herein, a series of AC/ZSM-5 composites were prepared to improve the adsorption performance for EtO, evaluated by dynamic breakthrough experiments. Particularly, the AC/ZSM-20% composite demonstrated a more excellent adsorption capacity of 81.9 mg/g at 25 °C and 50% RH than that of pristine AC and ZSM-5 with 32.5 and 52.3 mg/g, respectively. Moreover, the adsorption capacity of the AC/ZSM-20% composite remained constant even after five adsorption-desorption cycles. The adsorption mechanism of EtO on the composite is further revealed by density functional theory (DFT) calculations.