ZNZohaib Nasir
Zohaib Nasir
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zohaib Nasir has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Adnan Tariq
Mechanical Engineering Department, Wah Engineering College, University of Wah, Wah Cantt 47040, Pakistan
1 shared publication - Manzar Masud
Department of Mechanical Engineering, Capital University of Science and Technology (CUST), Islamabad 44000, Pakistan
1 shared publication - Moazzam Ali Babar
Mechanical Engineering Department, Wah Engineering College, University of Wah, Wah Cantt 47040, Pakistan
1 shared publication - Muhammad Faisal Naveed
Mechanical Engineering Department, Wah Engineering College, University of Wah, Wah Cantt 47040, Pakistan
1 shared publication - Shahid Iqbal
Mechanical Engineering Department, Wah Engineering College, University of Wah, Wah Cantt 47040, Pakistan
1 shared publication - Taimoor Kausar
Mechanical Engineering Department, Wah Engineering College, University of Wah, Wah Cantt 47040, Pakistan
1 shared publication
Latest Publications
- Open Access
- 24 September 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 75 (1) , 13
Experimental Evaluation of Thermal Performance in Shell and Tube Heat Exchangers Using Al₂O₃-γ Nanofluids
Shell and tube heat exchangers (H.Xs) are being used broadly in the generation of power, refrigeration, nuclear, chemical, and petroleum industries due to their high cooling and heating capacity. In this research paper, an experimental test bench for a shell and tube H.X was fabricated according to the standard. This study aimed to test the thermal performance of shell and tube H.Xs using Al2O3-γ nanofluid with different concentrations in counter flow configurations. Nanoparticles of 12 nm of size and 99% purity were used in this investigation. These nanoparticles were dispersed in distilled water to prepare nanofluids at three different concentrations: 0.11%, 0.22%, and 0.34%. Nanofluids of different concentrations were heated and passed through H.X tubes while water was passed through the shell side. The experiments were performed at three different flow rates: 6, 8, and 10 L per minute (L/min). It was observed from the experimentation that nanofluid has higher efficiency as compared to simple distilled water. Experimental investigations showed higher values of overall heat transfer coefficient (U), convective heat transfer coefficient (h), and heat transfer rate () at 0.22%, noted as 33.33%, 48%, and 30%, respectively. The lowest value for U was noted 47% for distilled water. The hydrodynamic and thermal boundary layers were also determined, and when the flow rate increased it led to thinning of the thermal boundary layer and improved heat transfer; however, increased concentrations of nanoparticles thickened the boundary layer by increasing viscosity and boosting thermal conductivity (k) simultaneously. It was revealed that the best concentration for maximizing heat transfer was 0.22%. The findings show that heat transmission efficiency was improved at both 0.11% and 0.22% of nanofluids compared to simple distilled water; when the concentration was raised to 0.34%, the results decreased due to increasing viscosity. Therefore, there is a need to precisely adjust the nanoparticle loading rate for maximum heat transfer enhancement without affecting fluid properties.- 24 September 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 75 (1) , 13
Open AccessExperimental Evaluation of Thermal Performance in Shell and Tube Heat Exchangers Using Al₂O₃-γ Nanofluids
Shell and tube heat exchangers (H.Xs) are being used broadly in the generation of power, refrigeration, nuclear, chemical, and petroleum industries due to their high cooling and heating capacity. In this research paper, an experimental test bench for a shell and tube H.X was fabricated according to the standard. This study aimed to test the thermal performance of shell and tube H.Xs using Al2O3-γ nanofluid with different concentrations in counter flow configurations. Nanoparticles of 12 nm of size and 99% purity were used in this investigation. These nanoparticles were dispersed in distilled water to prepare nanofluids at three different concentrations: 0.11%, 0.22%, and 0.34%. Nanofluids of different concentrations were heated and passed through H.X tubes while water was passed through the shell side. The experiments were performed at three different flow rates: 6, 8, and 10 L per minute (L/min). It was observed from the experimentation that nanofluid has higher efficiency as compared to simple distilled water. Experimental investigations showed higher values of overall heat transfer coefficient (U), convective heat transfer coefficient (h), and heat transfer rate () at 0.22%, noted as 33.33%, 48%, and 30%, respectively. The lowest value for U was noted 47% for distilled water. The hydrodynamic and thermal boundary layers were also determined, and when the flow rate increased it led to thinning of the thermal boundary layer and improved heat transfer; however, increased concentrations of nanoparticles thickened the boundary layer by increasing viscosity and boosting thermal conductivity (k) simultaneously. It was revealed that the best concentration for maximizing heat transfer was 0.22%. The findings show that heat transmission efficiency was improved at both 0.11% and 0.22% of nanofluids compared to simple distilled water; when the concentration was raised to 0.34%, the results decreased due to increasing viscosity. Therefore, there is a need to precisely adjust the nanoparticle loading rate for maximum heat transfer enhancement without affecting fluid properties.