JPJong Dae Park

Jong Dae Park

*This is an algorithmically generated author record based on publicly available information.

Jong Dae Park has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development and verification of a simulation model for the power transmission system of a 20 kW electric tractor

    by Dong Wook Kim, Ji Hun Yu, Min Jong Park, Jong Dae Park, Yong Joo Kim

    This study aimed to verify the agricultural working performance of an electric tractor by developing a 1-D power transmission system simulation model using SimulationX (ver. 4.4, ESI ITI GmbH, Germany). A load measurement system was installed on the electric tractor to measure real-time data during plow tillage, including axle torque and the state of charge (SOC) level of the battery. The t-tests were conducted to compare the measured and simulated axle torques and validated the simulation model. The p-values for the front and rear axles were 0.18 and 0.19, respectively, indicating no statistically significant differences. Although the measured and simulated SOC did not perfectly match, the trends showed similar patterns. The divergences in SOC were mainly due to the resolution limitations of the SOC sensor during measurement. Based on both measured and simulated results, the estimated workable time for plow tillage using the electric tractor was approximately 2 hours.

  • Open Access

    Simulation of the power transmission durability for a 20 kW single motor driving electric tractor

    by Dong Wook Kim, Ji Hun Yu, Jong Dae Park, Min Jong Park, Yong Joo Kim

    This study aimed to develop a simulation model and validate the durability of a 20-kW electric tractor power transmission. Power transmission consisted of a motor, transmission, axle and wheels. The transmission simulation model was developed using MASTA, a gear analysis software, and motor rotational speed, as well as wheel and power takeoff (PTO) torque generated during agricultural work were applied as input parameters of the simulation model. The safety factors of the gears and bearing damage were analyzed. The power transmission durability test was conducted using a dynamometer. The input motor speed was adjusted by the input speed, and the load motor torque was adjusted by applied the load under test conditions. Zero-failure test times were 2,418 hours, whereas acceleration life testing (ALT) was approximately 160 hours using the dynamometer. The gear safety analysis results showed that the bending safety factor of the pinion in spiral bevel gear was 1.19 and the contact safety factor was also 1.12 which was the lowest among all gear pairs. The bearing safety analysis showed that the highest bearing damage rate was 58.69%, and the lowest safety factor of 1.30. Gear and bearing analysis results of the powertrain satisfied the target safety. However, spalling was found in one tooth of the differential pinion gear. The face width of the damaged spiral bevel gear was changed from 41 to 43, and the safety factor was analyzed. The bending and contact safety factors were 1.71 and 1.32, respectively, which were improved by approximately 44% and 18%. It is judged that power transmission would be applied to electric tractors.


  • Open Access

    Analysis of driving axle and PTO power transmission efficiency of an 18 kW-class single motor electric tractor

    by Cheol Woo Yang, Gyeong Eui Nam, Han Yeol Yu, Jong Dae Park, Jin Woo Jeong, Seung Yun Baek, Yong Joo Kim, Nyun Ki Chung


  • Open Access

    Dynamic characteristics of a tractor cabin during plow tillage and rotary tillage

    by Jong Dae Park, Min Jong Park, Seung Yun Baek, Hyeon Ho Jeon, Dae Wun Kim, Dae Seung Hwang, Yong Joo Kim

    Due to the environment of irregular soil characteristic for agricultural fields, dynamic characteristic occurs in the tractor cabin during agricultural operations. Operator's fatigue is increased, and operation performance is decreased by these irregular environment conditions. This study was conducted to measure and analyze the dynamic characteristic of a tractor cabin, a major agriculture machinery, during agricultural operations. The specification of tractor used in the study was a 95 kW class tractor. To analyze the dynamic characteristics of the tractor cabin, the main agricultural operations, plow tillage and rotary tillage, were selected. To measure data of dynamic characteristic of the cabin, which continuously changes during operations, an Ellipse Series INS (inertia navigation system) with a built-in IMU (inertia measurement unit) was attached to the center of gravity of the cabin. During field test, the gear stages of plow tillage were B4 (4.3 km•h-1) and B5 (5.6 km•h-1), and the gear stages of rotary tillage were A3 (3.3 km•h-1) and A4 (4.2 km•h-1), which are the most commonly used. To analyze dynamic characteristic such as roll and pitch during operations according to the gear stages. As a result, the dynamic characteristics of pitch increased more than the dynamic characteristics of roll as the travel speed increased, and the dynamic characteristics of both agricultural operations were in the range of 2 to 5°.