Dong Wook Kim
Dong Wook Kim has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Yong-Joo Kim
Eco-Friendly Hydrogen Electric Tractor & Agricultural Machinery Institute, Chungnam National University, Daejeon 34134, Republic of Korea
3 shared publications - Ji Hun Yu
Department of Tractor R&D Center LS Mtron 55322 Wanju Korea
2 shared publications - Jong Dae Park2 shared publications
- Min Jong Park
Department of Smart Agriculture Systems Chungnam National University 34134 Daejeon Korea
2 shared publications Deok-Hyun Ko
1 shared publicationHyeon-Ho Jeon
1 shared publication
Latest Publications
- 4 November 2026
- Published by Elsevier in Measurement
- Vol. 293
A multi-objective optimization framework for accelerated life test design of an electric tractor transmission
- 4 November 2026
- Published by Elsevier in Measurement
- Vol. 293
A multi-objective optimization framework for accelerated life test design of an electric tractor transmission
- Open Access
- 1 December 2025
- Published by Institute of Agricultural Science, Chungnam National University in Korean Journal of Agricultural Science
- Vol. 52 (4) , 471-480
Development and verification of a simulation model for the power transmission system of a 20 kW electric tractor
This study aimed to verify the agricultural working performance of an electric tractor by developing a 1-D power transmission system simulation model using SimulationX (ver. 4.4, ESI ITI GmbH, Germany). A load measurement system was installed on the electric tractor to measure real-time data during plow tillage, including axle torque and the state of charge (SOC) level of the battery. The t-tests were conducted to compare the measured and simulated axle torques and validated the simulation model. The p-values for the front and rear axles were 0.18 and 0.19, respectively, indicating no statistically significant differences. Although the measured and simulated SOC did not perfectly match, the trends showed similar patterns. The divergences in SOC were mainly due to the resolution limitations of the SOC sensor during measurement. Based on both measured and simulated results, the estimated workable time for plow tillage using the electric tractor was approximately 2 hours.
- 1 December 2025
- Published by Institute of Agricultural Science, Chungnam National University in Korean Journal of Agricultural Science
- Vol. 52 (4) , 471-480
Open AccessDevelopment and verification of a simulation model for the power transmission system of a 20 kW electric tractor
This study aimed to verify the agricultural working performance of an electric tractor by developing a 1-D power transmission system simulation model using SimulationX (ver. 4.4, ESI ITI GmbH, Germany). A load measurement system was installed on the electric tractor to measure real-time data during plow tillage, including axle torque and the state of charge (SOC) level of the battery. The t-tests were conducted to compare the measured and simulated axle torques and validated the simulation model. The p-values for the front and rear axles were 0.18 and 0.19, respectively, indicating no statistically significant differences. Although the measured and simulated SOC did not perfectly match, the trends showed similar patterns. The divergences in SOC were mainly due to the resolution limitations of the SOC sensor during measurement. Based on both measured and simulated results, the estimated workable time for plow tillage using the electric tractor was approximately 2 hours.
- Open Access
- 1 December 2025
- Published by Institute of Agricultural Science, Chungnam National University in Korean Journal of Agricultural Science
- Vol. 52 (4) , 427-446
Simulation of the power transmission durability for a 20 kW single motor driving electric tractor
This study aimed to develop a simulation model and validate the durability of a 20-kW electric tractor power transmission. Power transmission consisted of a motor, transmission, axle and wheels. The transmission simulation model was developed using MASTA, a gear analysis software, and motor rotational speed, as well as wheel and power takeoff (PTO) torque generated during agricultural work were applied as input parameters of the simulation model. The safety factors of the gears and bearing damage were analyzed. The power transmission durability test was conducted using a dynamometer. The input motor speed was adjusted by the input speed, and the load motor torque was adjusted by applied the load under test conditions. Zero-failure test times were 2,418 hours, whereas acceleration life testing (ALT) was approximately 160 hours using the dynamometer. The gear safety analysis results showed that the bending safety factor of the pinion in spiral bevel gear was 1.19 and the contact safety factor was also 1.12 which was the lowest among all gear pairs. The bearing safety analysis showed that the highest bearing damage rate was 58.69%, and the lowest safety factor of 1.30. Gear and bearing analysis results of the powertrain satisfied the target safety. However, spalling was found in one tooth of the differential pinion gear. The face width of the damaged spiral bevel gear was changed from 41 to 43, and the safety factor was analyzed. The bending and contact safety factors were 1.71 and 1.32, respectively, which were improved by approximately 44% and 18%. It is judged that power transmission would be applied to electric tractors.
- 1 December 2025
- Published by Institute of Agricultural Science, Chungnam National University in Korean Journal of Agricultural Science
- Vol. 52 (4) , 427-446
Open AccessSimulation of the power transmission durability for a 20 kW single motor driving electric tractor
This study aimed to develop a simulation model and validate the durability of a 20-kW electric tractor power transmission. Power transmission consisted of a motor, transmission, axle and wheels. The transmission simulation model was developed using MASTA, a gear analysis software, and motor rotational speed, as well as wheel and power takeoff (PTO) torque generated during agricultural work were applied as input parameters of the simulation model. The safety factors of the gears and bearing damage were analyzed. The power transmission durability test was conducted using a dynamometer. The input motor speed was adjusted by the input speed, and the load motor torque was adjusted by applied the load under test conditions. Zero-failure test times were 2,418 hours, whereas acceleration life testing (ALT) was approximately 160 hours using the dynamometer. The gear safety analysis results showed that the bending safety factor of the pinion in spiral bevel gear was 1.19 and the contact safety factor was also 1.12 which was the lowest among all gear pairs. The bearing safety analysis showed that the highest bearing damage rate was 58.69%, and the lowest safety factor of 1.30. Gear and bearing analysis results of the powertrain satisfied the target safety. However, spalling was found in one tooth of the differential pinion gear. The face width of the damaged spiral bevel gear was changed from 41 to 43, and the safety factor was analyzed. The bending and contact safety factors were 1.71 and 1.32, respectively, which were improved by approximately 44% and 18%. It is judged that power transmission would be applied to electric tractors.