Yan Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yan Zhang has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Guoqian Wang
School of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 211816, China
1 shared publication - Moucun Yang
School of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 211816, China
1 shared publication - Yuqi Wu
School of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 211816, China
1 shared publication
Latest Publications
- Open Access
- 26 September 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (10) , 1191
Precision Electrochemical Micro-Machining of Molybdenum in Neutral Salt Solution Based on Electrochemical Analysis
Molybdenum is an important material in modern industry, widely used in extreme environments such as rocket engine nozzles and microelectrodes due to its high melting point, excellent mechanical properties, and thermal conductivity. However, as a difficult-to-machine metal, traditional machining methods struggle to achieve the desired microstructures in molybdenum. Electrochemical machining (ECM) offers unique advantages in manufacturing fine structures from hard-to-machine metals. Studies have shown that molybdenum exhibits a fast corrosion rate in alkaline or acidic solutions, posing significant environmental pressure. Therefore, this study investigates the electrochemical machining of molybdenum in neutral salt solutions to achieve high-precision microstructure fabrication. First, the polarization curves and electrochemical impedance spectroscopy (EIS) of molybdenum in NaNO3 solutions of varying concentrations were measured to determine its electrochemical reaction characteristics. The results demonstrate that molybdenum exhibits good electrochemical reactivity in NaNO3 solutions, leading to favorable surface erosion morphology. Subsequently, a mask electrochemical machining technique was employed to fabricate arrayed microstructures on the molybdenum surface. To minimize interference between factors, an orthogonal experiment was used to optimize the parameter combination, determining the optimal machining process parameters. Under these optimal conditions, an array of micro-groove structures was successfully fabricated with an average groove width of 110 μm, a depth-to-width ratio of 0.21, an aspect ratio of 9000, and a groove width error of less than 5 μm.
- 26 September 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (10) , 1191
Open AccessPrecision Electrochemical Micro-Machining of Molybdenum in Neutral Salt Solution Based on Electrochemical Analysis
Molybdenum is an important material in modern industry, widely used in extreme environments such as rocket engine nozzles and microelectrodes due to its high melting point, excellent mechanical properties, and thermal conductivity. However, as a difficult-to-machine metal, traditional machining methods struggle to achieve the desired microstructures in molybdenum. Electrochemical machining (ECM) offers unique advantages in manufacturing fine structures from hard-to-machine metals. Studies have shown that molybdenum exhibits a fast corrosion rate in alkaline or acidic solutions, posing significant environmental pressure. Therefore, this study investigates the electrochemical machining of molybdenum in neutral salt solutions to achieve high-precision microstructure fabrication. First, the polarization curves and electrochemical impedance spectroscopy (EIS) of molybdenum in NaNO3 solutions of varying concentrations were measured to determine its electrochemical reaction characteristics. The results demonstrate that molybdenum exhibits good electrochemical reactivity in NaNO3 solutions, leading to favorable surface erosion morphology. Subsequently, a mask electrochemical machining technique was employed to fabricate arrayed microstructures on the molybdenum surface. To minimize interference between factors, an orthogonal experiment was used to optimize the parameter combination, determining the optimal machining process parameters. Under these optimal conditions, an array of micro-groove structures was successfully fabricated with an average groove width of 110 μm, a depth-to-width ratio of 0.21, an aspect ratio of 9000, and a groove width error of less than 5 μm.