Constantin Alex Sumanariu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Constantin Alex Sumanariu has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Catalin Gheorghe Amza
National University of Science and Technology Politehnica Bucharest
2 shared publications - Adrian Ionut Nicoara
Department of Science and Engineering of Oxide Materials and Nanomaterials, Faculty of Chemical Engineering and Biotechnologies, National University of Science and Technology POLITEHNICA Bucharest, 1-7 Gheorghe Polizu, 011061 Bucharest, Romania
1 shared publication - Florin Baciu
Department of Strength of Materials, National University of Science and Technology POLITEHNICA Bucharest, Splaiul Independentei 313, 060042 Bucharest, Romania
1 shared publication - Mihai Ion Vasile
Department of Quality Engineering and Industrial Technologies, Faculty of Industrial Engineering and Robotics, National University of Science and Technology POLITEHNICA Bucharest, 060042 București, Romania
1 shared publication
Latest Publications
- 18 June 2025
- Published by Wiley in Macromolecular Symposia
- Vol. 414 (3)
Postirradiation Analysis And Comparison Of Additively Manufactured Stainless Steel 316L Samples
This research paper examines the behavior of stainless steel 316L samples manufactured using additive manufacturing (AM) and conventional methods in postirradiation conditions through analyzing the changes in their microstructure and mechanical characteristics. The alloy 316L, which is made of stainless steel was intentionally exposed to radiation in order to replicate the harsh conditions experienced in nuclear applications more specifically a reactor core environment. We conducted a comparative analysis of materials created using additive manufacturing (AM) and conventional methods using advanced characterization techniques including scanning electron microscopy (SEM) and tensile strength tests. The results obtained are qualitative and more quantitative data will be generated after the samples are less radioactive.
- 18 June 2025
- Published by Wiley in Macromolecular Symposia
- Vol. 414 (3)
Postirradiation Analysis And Comparison Of Additively Manufactured Stainless Steel 316L Samples
This research paper examines the behavior of stainless steel 316L samples manufactured using additive manufacturing (AM) and conventional methods in postirradiation conditions through analyzing the changes in their microstructure and mechanical characteristics. The alloy 316L, which is made of stainless steel was intentionally exposed to radiation in order to replicate the harsh conditions experienced in nuclear applications more specifically a reactor core environment. We conducted a comparative analysis of materials created using additive manufacturing (AM) and conventional methods using advanced characterization techniques including scanning electron microscopy (SEM) and tensile strength tests. The results obtained are qualitative and more quantitative data will be generated after the samples are less radioactive.
- Open Access
Comparative Analysis of Mechanical Properties: Conventional vs. Additive Manufacturing for Stainless Steel 316L
This research investigates the tensile strength and microstructural properties of stainless steel 316L, comparing samples fabricated using additive manufacturing (AM) to those produced via conventional manufacturing techniques such as forging and casting using stainless steel 316L for its mechanical performance and corrosion resistance. Tensile tests revealed that AM samples had an ultimate tensile strength (UTS) of 650 MPa, a yield strength of 550 MPa and an elongation at break of 20%, and conventionally manufactured samples achieved a UTS of 580 MPa, a yield strength of 450 MPa and a higher elongation at break of 35%. The reduced ductility of AM samples is offset by their higher strength. Scanning electron microscopy (SEM) analysis showed that AM samples had a refined grain structure, with grain sizes ranging from 1 to 5 µm, whereas conventionally produced samples exhibited larger grain sizes of 10 to 20 µm, contributing to their increased ductility. This shows that while AM processes can give a rather high strength, the ductility property is simpler to attain with casting. Further work is needed to investigate post-processing techniques like hot isotropic pressing (HIP) and heat treatments for enhancing the ductility of AM parts as well as mechanical properties.
Open AccessComparative Analysis of Mechanical Properties: Conventional vs. Additive Manufacturing for Stainless Steel 316L
This research investigates the tensile strength and microstructural properties of stainless steel 316L, comparing samples fabricated using additive manufacturing (AM) to those produced via conventional manufacturing techniques such as forging and casting using stainless steel 316L for its mechanical performance and corrosion resistance. Tensile tests revealed that AM samples had an ultimate tensile strength (UTS) of 650 MPa, a yield strength of 550 MPa and an elongation at break of 20%, and conventionally manufactured samples achieved a UTS of 580 MPa, a yield strength of 450 MPa and a higher elongation at break of 35%. The reduced ductility of AM samples is offset by their higher strength. Scanning electron microscopy (SEM) analysis showed that AM samples had a refined grain structure, with grain sizes ranging from 1 to 5 µm, whereas conventionally produced samples exhibited larger grain sizes of 10 to 20 µm, contributing to their increased ductility. This shows that while AM processes can give a rather high strength, the ductility property is simpler to attain with casting. Further work is needed to investigate post-processing techniques like hot isotropic pressing (HIP) and heat treatments for enhancing the ductility of AM parts as well as mechanical properties.