Seonggeun Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Seonggeun Kim has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Sangwan Kim
Sogang University
10 shared publications - Seungwon Go
Sogang University
7 shared publications - Sihyun Kim
Department of Electronic Engineering, Sogang University, Seoul, South Korea
6 shared publications - Dong Keun Lee
Department of Electronic Engineering, Sogang University, Seoul, Republic of Korea
3 shared publications - Jae Yeon Park
Department of Electronic Engineering, Sogang University, Seoul, South Korea
3 shared publications Hyungju Noh
Department of Electronics Engineering, Sogang University, Seoul 04107, Republic of Korea
2 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (9) , 1958-1961
Remote Oxygen Scavenging in MFIS Gate Stack With Laminated HfZrO Film
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (9) , 1958-1961
Remote Oxygen Scavenging in MFIS Gate Stack With Laminated HfZrO Film
- 13 August 2026
- Published by Elsevier in Applied Surface Science
- Vol. 751
Enhanced thermal robustness of laminated Hf0.5Zr0.5O2 ferroelectric film via Al2O3 mid-layer engineering
- 13 August 2026
- Published by Elsevier in Applied Surface Science
- Vol. 751
Enhanced thermal robustness of laminated Hf0.5Zr0.5O2 ferroelectric film via Al2O3 mid-layer engineering
- 7 November 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045353
Mechanical stability analysis of 3D nanosheet-stacked structure
The three-dimensionally (3D) stacked gate-all-around (GAA) nanosheet (NS) channel structures have been adopted into the state-of-the-art integrated circuit technologies to overcome the scaling limit of conventional device structure. However, a mechanical stress during the channel release process, which results in the channel deformation, is a severe concern for the high yield. In this study, the origins of the stress are examined by using a technology computer-aided design (TCAD) simulation and the design guidelines are proposed for the NS fabrication without the deformation. The results show that the stress is mainly determined by the active pads and NS length ratio ( L pad / L NS ). Finally, it is demonstrated by fabricating the NS with L pad / L NS = 1 that the mechanical stress is efficiently suppressed, thereby preventing the deformation.
- 7 November 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045353
Mechanical stability analysis of 3D nanosheet-stacked structure
The three-dimensionally (3D) stacked gate-all-around (GAA) nanosheet (NS) channel structures have been adopted into the state-of-the-art integrated circuit technologies to overcome the scaling limit of conventional device structure. However, a mechanical stress during the channel release process, which results in the channel deformation, is a severe concern for the high yield. In this study, the origins of the stress are examined by using a technology computer-aided design (TCAD) simulation and the design guidelines are proposed for the NS fabrication without the deformation. The results show that the stress is mainly determined by the active pads and NS length ratio ( L pad / L NS ). Finally, it is demonstrated by fabricating the NS with L pad / L NS = 1 that the mechanical stress is efficiently suppressed, thereby preventing the deformation.
- 4 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 24 (1536125X) , 413-416
Demonstration of Ferroelectric Tunnel Field-Effect Transistor for Low Power Synapse Device
In this paper, a ferroelectric tunnel field-effect transistor (FeTFET) is demonstrated as a synapse device. The experimental results clearly show that there are several merits in FeTFET as a synapse device comparing with the FeFET. First, the FeTFET shows the ∼3 orders lower drain current than the FeFET thanks to the different carrier injection mechanism (i.e., band-to-band tunneling). Second, the memory window of FeTFET (1.48 V) is ∼1.5 times larger than the FeFET (0.95 V) due to an enhanced erase efficiency. As a result, the FeTFET shows the better training accuracy (∼91.5% ) even with the ∼25 times lower energy consumption (∼0.16 mJ) comparing with the FeFET (∼90.4% accuracy with 4.06 mJ energy consumption). Lastly, the FeTFET shows a good retention property (> 10 years) with a ∼107 endurance characteristic. In short, the FeTFET can be a promising candidate for a low-power synapse device.
- 4 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 24 (1536125X) , 413-416
Demonstration of Ferroelectric Tunnel Field-Effect Transistor for Low Power Synapse Device
In this paper, a ferroelectric tunnel field-effect transistor (FeTFET) is demonstrated as a synapse device. The experimental results clearly show that there are several merits in FeTFET as a synapse device comparing with the FeFET. First, the FeTFET shows the ∼3 orders lower drain current than the FeFET thanks to the different carrier injection mechanism (i.e., band-to-band tunneling). Second, the memory window of FeTFET (1.48 V) is ∼1.5 times larger than the FeFET (0.95 V) due to an enhanced erase efficiency. As a result, the FeTFET shows the better training accuracy (∼91.5% ) even with the ∼25 times lower energy consumption (∼0.16 mJ) comparing with the FeFET (∼90.4% accuracy with 4.06 mJ energy consumption). Lastly, the FeTFET shows a good retention property (> 10 years) with a ∼107 endurance characteristic. In short, the FeTFET can be a promising candidate for a low-power synapse device.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (9) , 1648-1651
Impact of Al-Doping on Ferroelectricity and Reliability of HfZrO Film Under High Temperature Annealing
This study explores the influences of Al-doping on a ferroelectricity and a reliability of Hf ${}_{{0}.{5}}$ Zr ${}_{{0}.{5}}$ O2 (HZO) films with a high temperature annealing. The Al-doped HZO (Al:HZO) films, in which the Al2O3 (AlO) layers are uniformly doped into the HZO films, are fabricated by using the super-cycles of atomic layer deposition (ALD). All the Al:HZO films show the reduced leakage current, increased breakdown field, 10-year lifetime voltage (> 2.32 V), endurance (> $10^{{10}}$ cycles) without observable fatigue and wake-up effect. Among the Al:HZO films, the 72:1 cycle ratio (CR) exhibits the highest remanent polarization ( ${P}_{\text {r}}\text {)}$ of $\boldsymbol {\sim } 22.7~\boldsymbol {\mu }$ C/cm2, while the 36:1 CR offered an optimal trade-off between reliability and ${P}_{\text {r}}$ ( $\boldsymbol {\sim } 19.1~\boldsymbol {\mu }$ C/cm ${}^{{2}}\text {)}$ . These results suggest that the Al:HZO films are promising candidates for the next-generation 3D ferroelectric memory applications requiring high thermal budget compatibility and robust reliability.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (9) , 1648-1651
Impact of Al-Doping on Ferroelectricity and Reliability of HfZrO Film Under High Temperature Annealing
This study explores the influences of Al-doping on a ferroelectricity and a reliability of Hf ${}_{{0}.{5}}$ Zr ${}_{{0}.{5}}$ O2 (HZO) films with a high temperature annealing. The Al-doped HZO (Al:HZO) films, in which the Al2O3 (AlO) layers are uniformly doped into the HZO films, are fabricated by using the super-cycles of atomic layer deposition (ALD). All the Al:HZO films show the reduced leakage current, increased breakdown field, 10-year lifetime voltage (> 2.32 V), endurance (> $10^{{10}}$ cycles) without observable fatigue and wake-up effect. Among the Al:HZO films, the 72:1 cycle ratio (CR) exhibits the highest remanent polarization ( ${P}_{\text {r}}\text {)}$ of $\boldsymbol {\sim } 22.7~\boldsymbol {\mu }$ C/cm2, while the 36:1 CR offered an optimal trade-off between reliability and ${P}_{\text {r}}$ ( $\boldsymbol {\sim } 19.1~\boldsymbol {\mu }$ C/cm ${}^{{2}}\text {)}$ . These results suggest that the Al:HZO films are promising candidates for the next-generation 3D ferroelectric memory applications requiring high thermal budget compatibility and robust reliability.
- Open Access
- 4 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 101782-101788
Suppression of Reverse Drain-Induced Barrier Lowering in Negative Capacitance FETs Using a Hetero-Metal-Gate Structure
In this paper, the reverse drain-induced barrier lowering (RDIBL) in the negative capacitance field-effect transistor (NCFET) is discussed. It is found that the RDIBL is attributed to the increase of barrier height between channel and drain with the higher drain voltage (VDS). To address this issue, a hetero-metal-gate negative capacitance field-effect transistor (HM NCFET), which features the metal-gate composed of two different work function materials at source and drain sides, is proposed and its electrical characteristics are analyzed with the help of technology computer-aided design (TCAD) simulation. In contrast to the conventional NCFET, the HM NCFET can efficiently suppress RDIBL from -57 mV/V to -3 mV/V by decreasing the work function of metal-gate at drain side from 4.6 eV to 4.0 eV, while the work function of metal-gate at source side is fixed at 4.6 eV.
- 4 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 101782-101788
Open AccessSuppression of Reverse Drain-Induced Barrier Lowering in Negative Capacitance FETs Using a Hetero-Metal-Gate Structure
In this paper, the reverse drain-induced barrier lowering (RDIBL) in the negative capacitance field-effect transistor (NCFET) is discussed. It is found that the RDIBL is attributed to the increase of barrier height between channel and drain with the higher drain voltage (VDS). To address this issue, a hetero-metal-gate negative capacitance field-effect transistor (HM NCFET), which features the metal-gate composed of two different work function materials at source and drain sides, is proposed and its electrical characteristics are analyzed with the help of technology computer-aided design (TCAD) simulation. In contrast to the conventional NCFET, the HM NCFET can efficiently suppress RDIBL from -57 mV/V to -3 mV/V by decreasing the work function of metal-gate at drain side from 4.6 eV to 4.0 eV, while the work function of metal-gate at source side is fixed at 4.6 eV.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (6) , 3302-3306
One-Ferroelectric-Tunnel-FET-Based Reconfigurable Logic Gates
A novel reconfigurable logic gate (RLG) utilizing one ferroelectric tunnel field-effect transistor (FeTFET) is proposed for the first time. By leveraging the symmetric ambipolar current of the TFET and the minor loop behavior of the ferroelectric, NAND/OR/XNOR/IMP/RIMP operations are performed within a single FeTFET, enabling logic-in-memory (LiM) with high area efficiency. It is demonstrated that two inputs can be programmed in two steps, and the type of logic operation can be changed by simply altering the read voltage. The proposed FeTFET-based RLGs consume >99% lower operation energy than FeFET-based ones.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (6) , 3302-3306
One-Ferroelectric-Tunnel-FET-Based Reconfigurable Logic Gates
A novel reconfigurable logic gate (RLG) utilizing one ferroelectric tunnel field-effect transistor (FeTFET) is proposed for the first time. By leveraging the symmetric ambipolar current of the TFET and the minor loop behavior of the ferroelectric, NAND/OR/XNOR/IMP/RIMP operations are performed within a single FeTFET, enabling logic-in-memory (LiM) with high area efficiency. It is demonstrated that two inputs can be programmed in two steps, and the type of logic operation can be changed by simply altering the read voltage. The proposed FeTFET-based RLGs consume >99% lower operation energy than FeFET-based ones.
- 7 January 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (7) , 3587-3594
Enhancing AC stress stability in amorphous indium gallium zinc oxide thin-film transistors via controlled hydrogen diffusion
To optimize the hydrogen content in a -IGZO TFTs, hafnium oxide (HfO 2 ) passivation via atomic layer deposition (ALD) and subsequent annealing were used. As a result, AC stress stability was improved, reducing the I on degradation rate from 69% to 9%.
- 7 January 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (7) , 3587-3594
Enhancing AC stress stability in amorphous indium gallium zinc oxide thin-film transistors via controlled hydrogen diffusion
To optimize the hydrogen content in a -IGZO TFTs, hafnium oxide (HfO 2 ) passivation via atomic layer deposition (ALD) and subsequent annealing were used. As a result, AC stress stability was improved, reducing the I on degradation rate from 69% to 9%.
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (10) , 2001-2004
Impact of Zr Precursor on Electrical Characteristics of HfZrO Laminated Structure
In this study, the effects of Zr precursor [i.e., tetrakis(ethylmethylamino) Zr (TEMA-Zr) and cyclopentadi- enyl tris(dimethylamino) Zr (Cp-Zr)] on the laminated HfZrO (HZO) are investigated for the enhanced ferroelectric characteristics. The laminated HZO film with the Cp-Zr shows superior ferroelectricity (i.e., remnant polarization, spontaneous polarization, and coercive field) and dielectric constant owing to the higher proportion of the tetragonal phase (t-phase) and orthorhombic phase (o-phase). Therefore, the TEMA-Hf/Cp-Zr sample shows up to ~1.6 times larger memory window (MW) at the same film thickness (i.e., the film thickness can be reduced by ~37% with same MW) than the TEMA-Hf/TEMA-Zr sample. Moreover, the TEMA-Hf/Cp-Zr sample features the lower leakage current and the larger breakdown voltage. Accordingly, it is expected that the FeFET with the TEMA-Hf/Cp-Zr laminated structure can be applied to multibit operation with enhanced electrical characteristics.
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (10) , 2001-2004
Impact of Zr Precursor on Electrical Characteristics of HfZrO Laminated Structure
In this study, the effects of Zr precursor [i.e., tetrakis(ethylmethylamino) Zr (TEMA-Zr) and cyclopentadi- enyl tris(dimethylamino) Zr (Cp-Zr)] on the laminated HfZrO (HZO) are investigated for the enhanced ferroelectric characteristics. The laminated HZO film with the Cp-Zr shows superior ferroelectricity (i.e., remnant polarization, spontaneous polarization, and coercive field) and dielectric constant owing to the higher proportion of the tetragonal phase (t-phase) and orthorhombic phase (o-phase). Therefore, the TEMA-Hf/Cp-Zr sample shows up to ~1.6 times larger memory window (MW) at the same film thickness (i.e., the film thickness can be reduced by ~37% with same MW) than the TEMA-Hf/TEMA-Zr sample. Moreover, the TEMA-Hf/Cp-Zr sample features the lower leakage current and the larger breakdown voltage. Accordingly, it is expected that the FeFET with the TEMA-Hf/Cp-Zr laminated structure can be applied to multibit operation with enhanced electrical characteristics.