Karin Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Karin Yu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Eleni Chatzi
ETH Zurich
3 shared publications - Jaime Mata-Falcón
ETH Zurich
2 shared publications - Walter Kaufmann
Institute of Structural Engineering (IBK) ETH Zürich Zürich Switzerland
2 shared publications - Andrew W. Smyth
Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, NY 10027, USA
1 shared publication - Boyan I. Mihaylov
Department of ArGEnCo University of Liège Liège Belgium
1 shared publication Eleni Chatzi
1 shared publication
Latest Publications
- Open Access
- 23 June 2026
- Published by Wiley in Structural Concrete
- Vol. 27 (5) , 7727-7745
Experimental and analytical investigations on the effect of steel fibers on the crack behavior and strength of dapped‐end connections
Reinforced concrete (RC) dapped‐end connections feature a sharp re‐entrant corner subjected to high stress concentrations, leading to wide cracks under service loads and potential durability issues such as reinforcement corrosion. Effective crack control is therefore essential in the design of new dapped‐end connections. Steel fiber reinforced concrete (SFRC) has shown potential to improve crack control while also enhancing ultimate strength. This study proposes a kinematics‐based model to describe the response of SFRC dapped ends along the re‐entrant corner crack. Appropriate constitutive relationships are used to link the deformations along the corner crack and the compression zone to the resisting forces: reinforcement and SFRC in compression and tension. The model is validated against eight large‐scale tests with varying fiber amounts including detailed deformation measurements from which the resisting mechanisms and crack‐opening behavior are derived. The experimental results show that a fiber amount of 70 kg/m 3 reduces the crack width by about 40%, enabling compliance with code requirements. The validation demonstrates that the proposed model represents a reliable tool for designing SFRC dapped‐end connections at both service and ultimate limit states.
- 23 June 2026
- Published by Wiley in Structural Concrete
- Vol. 27 (5) , 7727-7745
Open AccessExperimental and analytical investigations on the effect of steel fibers on the crack behavior and strength of dapped‐end connections
Reinforced concrete (RC) dapped‐end connections feature a sharp re‐entrant corner subjected to high stress concentrations, leading to wide cracks under service loads and potential durability issues such as reinforcement corrosion. Effective crack control is therefore essential in the design of new dapped‐end connections. Steel fiber reinforced concrete (SFRC) has shown potential to improve crack control while also enhancing ultimate strength. This study proposes a kinematics‐based model to describe the response of SFRC dapped ends along the re‐entrant corner crack. Appropriate constitutive relationships are used to link the deformations along the corner crack and the compression zone to the resisting forces: reinforcement and SFRC in compression and tension. The model is validated against eight large‐scale tests with varying fiber amounts including detailed deformation measurements from which the resisting mechanisms and crack‐opening behavior are derived. The experimental results show that a fiber amount of 70 kg/m 3 reduces the crack width by about 40%, enabling compliance with code requirements. The validation demonstrates that the proposed model represents a reliable tool for designing SFRC dapped‐end connections at both service and ultimate limit states.
- Open Access
- 1 June 2026
- Published by Wiley in Structural Concrete
Reverse engineering strut‐and‐tie models for assessing reinforced concrete structures
Strut‐and‐tie models enable the design of reinforced concrete structures with static or geometrical discontinuities, providing interpretability and control over the load path. These models are valuable for designing discontinuity regions of new structures and for validating nonlinear finite‐element analysis results. However, developing a strut‐and‐tie model for a given geometry and reinforcement layout—as required for the structural assessment of existing structures—is particularly challenging due to time constraints and the need for engineering expertise. This work addresses these issues by proposing a two‐stage method to reverse engineer strut‐and‐tie models and to maximize the load‐bearing capacity based on a given reinforcement layout, geometry, material properties, and proportional load case. The method combines elements of discrete layout optimization, various simplification and sparsification techniques and nonlinear nonconvex geometry optimization to generate simple, interpretable strut‐and‐tie models. Four literature examples demonstrate the suitability of the proposed method across varying levels of complexity and scale. This marks the first steps toward automating the derivation of strut‐and‐tie models for structural assessment, thereby improving efficiency without compromising interpretability and supporting practicing engineers in their daily tasks.
- 1 June 2026
- Published by Wiley in Structural Concrete
Open AccessReverse engineering strut‐and‐tie models for assessing reinforced concrete structures
Strut‐and‐tie models enable the design of reinforced concrete structures with static or geometrical discontinuities, providing interpretability and control over the load path. These models are valuable for designing discontinuity regions of new structures and for validating nonlinear finite‐element analysis results. However, developing a strut‐and‐tie model for a given geometry and reinforcement layout—as required for the structural assessment of existing structures—is particularly challenging due to time constraints and the need for engineering expertise. This work addresses these issues by proposing a two‐stage method to reverse engineer strut‐and‐tie models and to maximize the load‐bearing capacity based on a given reinforcement layout, geometry, material properties, and proportional load case. The method combines elements of discrete layout optimization, various simplification and sparsification techniques and nonlinear nonconvex geometry optimization to generate simple, interpretable strut‐and‐tie models. Four literature examples demonstrate the suitability of the proposed method across varying levels of complexity and scale. This marks the first steps toward automating the derivation of strut‐and‐tie models for structural assessment, thereby improving efficiency without compromising interpretability and supporting practicing engineers in their daily tasks.
- Open Access
- 6 January 2026
- Published by Elsevier in Advanced Engineering Informatics
- Vol. 71
Guided generation of strut-and-tie models for reinforced concrete structures with parametric graph grammatical evolution
- 6 January 2026
- Published by Elsevier in Advanced Engineering Informatics
- Vol. 71
Open AccessGuided generation of strut-and-tie models for reinforced concrete structures with parametric graph grammatical evolution
- Open Access
- 1 October 2025
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 240
Grammar-based ordinary differential equation discovery
- 1 October 2025
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 240
Open AccessGrammar-based ordinary differential equation discovery
- Open Access
- 7 October 2024
- Published by Elsevier in Engineering Structures
- Vol. 322
Experimental and analytical investigation of the crack behaviour of dapped-end beams
- 7 October 2024
- Published by Elsevier in Engineering Structures
- Vol. 322
Open AccessExperimental and analytical investigation of the crack behaviour of dapped-end beams
- Open Access
- 25 September 2024
- Published by Elsevier in Computers & Structures
- Vol. 305
Grammar-based generation of strut-and-tie models for designing reinforced concrete structures
- 25 September 2024
- Published by Elsevier in Computers & Structures
- Vol. 305
Open AccessGrammar-based generation of strut-and-tie models for designing reinforced concrete structures
- 19 June 2023
- Published by Springer Nature
- p. 133-140
A Spatio-Temporal Model for Response and Distributed Wave Load Estimation on Offshore Wind Turbines
- 19 June 2023
- Published by Springer Nature
- p. 133-140
A Spatio-Temporal Model for Response and Distributed Wave Load Estimation on Offshore Wind Turbines