Henry H. M. Moldenhauer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Henry H. M. Moldenhauer has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Carmine P. Polito
Department of Civil and Environmental Engineering, Valparaiso University, Valparaiso, IN 46383, USA
2 shared publications - Ashraf Bastawros
Department of Aerospace Engineering Iowa State University Ames Iowa USA
1 shared publication - Stephen D. Holland
Department of Aerospace Engineering, Iowa State University, Ames, USA
1 shared publication - Zhuoyue Zhang
Department of Civil and Environmental Engineering, Valparaiso University, 1900 Chapel Drive, Valparaiso, IN 46383, USA
1 shared publication
Latest Publications
- 11 January 2025
- Published by Springer Nature in International Journal of Fracture
- Vol. 249 (1) , 1-18
Incremental closure method to estimate changes in contact stress distributions for partially closed fatigue cracks in mode I loading
- 11 January 2025
- Published by Springer Nature in International Journal of Fracture
- Vol. 249 (1) , 1-18
Incremental closure method to estimate changes in contact stress distributions for partially closed fatigue cracks in mode I loading
- Open Access
- 9 October 2024
- Published by MDPI AG in Geotechnics
- Vol. 4 (4) , 1026-1047
Dissipation of Energy and Generation of Pore Pressure in Load-Controlled and Displacement-Controlled Cyclic Tests
The amount of energy dissipated in the soil during cyclic loading controls the amount of pore pressure generated under that loading. Because of this, the normalized dissipated energy per unit volume is the basis for both pore pressure generation models and energy-based liquefaction analyses. The pattern of energy dissipation in the soil in load-controlled cyclic triaxial and load-controlled cyclic direct simple shear tests and displacement-controlled cyclic triaxial and displacement-controlled cyclic direct simple shear tests is quite different. As a result, the pattern of pore pressure generation associated with load-controlled tests is markedly different from that in displacement-controlled tests. Pore pressure generation patterns for each of the four test types were proposed based upon the manner in which the load was applied during the test and the soil’s response to that loading. The results of four tests, two load controlled and two displacement controlled, were then used to verify these patterns. Pore pressure generation rates in load-controlled and displacement-controlled tests are different when plotted against their cycle ratios. Conversely, the tests produce nearly identical patterns when plotted against energy dissipation ratio. This occurs because of the relationship between energy dissipation ratio and pore pressure generation is independent of the loading pattern.
- 9 October 2024
- Published by MDPI AG in Geotechnics
- Vol. 4 (4) , 1026-1047
Open AccessDissipation of Energy and Generation of Pore Pressure in Load-Controlled and Displacement-Controlled Cyclic Tests
The amount of energy dissipated in the soil during cyclic loading controls the amount of pore pressure generated under that loading. Because of this, the normalized dissipated energy per unit volume is the basis for both pore pressure generation models and energy-based liquefaction analyses. The pattern of energy dissipation in the soil in load-controlled cyclic triaxial and load-controlled cyclic direct simple shear tests and displacement-controlled cyclic triaxial and displacement-controlled cyclic direct simple shear tests is quite different. As a result, the pattern of pore pressure generation associated with load-controlled tests is markedly different from that in displacement-controlled tests. Pore pressure generation patterns for each of the four test types were proposed based upon the manner in which the load was applied during the test and the soil’s response to that loading. The results of four tests, two load controlled and two displacement controlled, were then used to verify these patterns. Pore pressure generation rates in load-controlled and displacement-controlled tests are different when plotted against their cycle ratios. Conversely, the tests produce nearly identical patterns when plotted against energy dissipation ratio. This occurs because of the relationship between energy dissipation ratio and pore pressure generation is independent of the loading pattern.
- 7 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 336-344
Pore Pressure Generation and Dissipated Energy Ratio in Cohesionless Soils
Under cyclic loading, loose, saturated cohesionless soils develop excess pore pressures and decreased effective stresses and thus, decreased strengths. Lee and Albaisa showed that when pore pressure ratio is plotted against cycle ratio (the ratio of the current cycle of loading to the number of cycles of loading required to initiate liquefaction), the results plotted within a relatively narrow band. Excess pore pressure generation during cyclic loading has also been shown to be proportional to the energy dissipated in the soil during loading. The study reported here used the results of over 135 cyclic triaxial tests performed on sands and non-plastic silts to determine that when pore pressure ratio was plotted against dissipated energy ratio (the ratio of the cumulative dissipated energy to the dissipated energy required to initiate liquefaction), the relationship between pore pressure ratio and dissipated energy ratio is independent of the specimen’s relative density, silt content, magnitude of loading, number of cycles of loading required to initiate liquefaction, and normalized dissipated energy per unit volume required to cause liquefaction in the specimen.
- 7 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 336-344
Pore Pressure Generation and Dissipated Energy Ratio in Cohesionless Soils
Under cyclic loading, loose, saturated cohesionless soils develop excess pore pressures and decreased effective stresses and thus, decreased strengths. Lee and Albaisa showed that when pore pressure ratio is plotted against cycle ratio (the ratio of the current cycle of loading to the number of cycles of loading required to initiate liquefaction), the results plotted within a relatively narrow band. Excess pore pressure generation during cyclic loading has also been shown to be proportional to the energy dissipated in the soil during loading. The study reported here used the results of over 135 cyclic triaxial tests performed on sands and non-plastic silts to determine that when pore pressure ratio was plotted against dissipated energy ratio (the ratio of the cumulative dissipated energy to the dissipated energy required to initiate liquefaction), the relationship between pore pressure ratio and dissipated energy ratio is independent of the specimen’s relative density, silt content, magnitude of loading, number of cycles of loading required to initiate liquefaction, and normalized dissipated energy per unit volume required to cause liquefaction in the specimen.