BEB. S. Ermakov

B. S. Ermakov

*This is an algorithmically generated author record based on publicly available information.

B. S. Ermakov has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Effect of post-weld heat treatment of steel pipe billets on the performance of bored precast piles operated in permafrost soils

    by S. A. Yalygin, B. S. Ermakov, O. V. Shvetsov, N. I. Golikov, S. A. Vologzhanina

    The development of hydrocarbon production sites in permafrost zones and the need to reduce costs require a more thorough study of the requirements for the materials and structures used. An analysis of regulatory and technical documentation revealed that some of these requirements are unreasonably high. Thus, SP 16.13330.2020 specifies that when manufacturing bored precast foundation piles, it is necessary to ensure an impact toughness level of welded joints obtained by high-frequency welding of at least 34 J/cm2 at a temperature of -60 °C. This requires extensive post-weld heat treatment of the pipes from which the piles are made, dramatically increasing the cost of the structure and leading to higher construction costs. It should be noted that GOST 20295, which is used to manufacture pipes for the piles, and similar regulatory and technical documents do not contain such requirements. An analysis of the mechanical properties and residual welding stresses in the pipes with and without heat treatment was conducted. Field tests of bored precast piles installed in the permafrost zone were also conducted. The conducted studies allow to conclude that the requirement for heat treatment of the pipes is excessive and should be eliminated.This work was carried out as part of a state assignment from the Ministry of Science and Higher Education of the Russian Federation (Topic No. FSEG-2024-0009: Development of models for the degradation of the performance properties of metallic and composite materials for construction in permafrost soils).

  • Application of plasma atomization for obtaining non-ferrous metal powders

    by S. B. Ermakov, B. S. Ermakov, O. V. Shvetsov, S. A. Vologzhanina

    The use of additive technologies in various industries using 3D-printers poses a number of challenges for materials research. It is important to know what initial metal powders are used to manufacture parts, assemblies, and even finished products. The wide range of mechanical engineering products raises the question of the possibility of using different grades of materials for additive technologies. Powder materials are subject to a number of strict requirements for chemical composition, absence of defects, and formation of various compounds on the surface, structure, and sphericity of the resulting particles. Depending on the 3D-printing method, it is necessary to ensure the requirements for the granulometric composition of the powders. The article considers the production of powder materials by plasma atomization, and provides recommended process parameters for the operation of the atomizer to obtain the maximum amount of powders of commercial fractions. It is shown that the occurrence of particle porosity can be affected by the quality of wire preparation, plasma-forming and shielding gases. The influence of various factors on obtaining a stable crystallization structure is considered. It has been established that control of temperature and flows of protective gas in the spray chamber allows to minimize the number of nano- and ultra-dispersed defects: micro-liquations and segregations in the volume of powder particles. The paper presents data confirming the possibility of using the method of plasma spraying of solid feedstocks to obtain high-quality powders for additive machines from alloys based on nickel, titanium, and copper. It has been shown that the obtained powders can be used to manufacture products by methods of direct or selective laser melting of parts, units, and mechanisms for various purposes.

  • Causes of accelerated failure of excavator bucket teeth crowns when operating in Arctic regions

    by B. S. Ermakov, S. A. Vologzhanina, S. B. Ermakov, O. V. Shvetsov

    The mining industry is gradually moving to the Arctic region characterized by permafrost and permafrost soils. Excavation of rocks in these regions is hampered by increased rock strength due to ice freezing of rock pieces after stripping works and requires a new approach to the production of quick-change tools for excavator and loader buckets. The paper analyzes the causes of accelerated failure of excavator bucket crowns after operation in winter in the northern regions of the country; it is shown that the main causes of their accelerated failure are casting defects and insufficient cold resistance of crown material. Hot foundry cracks and large non-metallic inclusions are the initiators of accelerated failure, fatigue cracks and cold brittle cracks develop on their basis during operation. Insufficient cold resistance of steel grades used for these regions and their heat treatment modes have been confirmed, which leads to the development of brittle fracture cracks. It is established that in order to increase the serviceability of excavator crown metal operating in cold climate conditions it is necessary to modify the chemical composition of steel aimed at increasing its cold resistance while maintaining the level of strength and hardness, the main directions of steel composition modification are determined.The study was supported by the Russian Science Foundation grant No. 24-29-00713, https://rscf.ru/project/24-29-00713/.