S. A. Vologzhanina
S. A. Vologzhanina has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- B. S. Ermakov3 shared publications
- Boris S. Ermakov
Peter the Great St. Petersburg Polytechnic University
3 shared publications O. V. Shvetsov
3 shared publicationsR. M. Khuznakhmetov
3 shared publications- Nikita Shaposhnikov
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russian Federation
2 shared publications - Oleg V. Shvetsov
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russian Federation
2 shared publications
Latest Publications
- 30 May 2026
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 5,p. 69-74
Evaluation of the corrosion resistance of laser marking on 12Kh18N10T steel products
This article presents the results of tests evaluating the corrosion resistance of convex laser markings obtained by forming a relief pattern through melt control in the laser-impacted zone in the surface layer of 12Kh18N10T austenitic steel used to manufacture LNG logistics equipment (tanks and cylinders, tankers, road and rail tankers, pipelines, and pipeline fittings). The relevance of this work is due to the operation of these products in challenging atmospheric conditions typical of coastal zones and industrial regions, where exposure to chloride aerosols, condensates, and the acidic environment of marshy and peaty soils is possible. Tests were conducted on specimens with a relief pattern in the central portion and control specimens without laser processing. The relief was formed using a TurboMarker automated system with a fiber laser (λ = 1064 nm, τ = 100 ns, Pnom = 100 W) using specified scanning modes. Corrosion tests were conducted in a salt spray chamber under various conditions. Surface condition was assessed visually, gravimetrically, and by optical metallography. Electrochemical studies were also conducted, comparing the characteristics of the base metal and laser-treated area for corrosion potential, pitting potential, and pitting resistance. After testing, no corrosion or pitting products were detected on the samples, nor was any significant weight loss observed. The surface texture remained legible, which is important for traceability during maintenance and repair. Electrochemical data showed no signs of intense degradation of the passive state under the test conditions. The results confirm the feasibility of using convex laser marking as a durable identification method for LNG equipment components, resistant to external aggressive influences.The authors express their gratitude to the staff of Peter the Great St. Petersburg Polytechnic University for their assistance in conducting this research.
- 30 May 2026
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 5,p. 69-74
Evaluation of the corrosion resistance of laser marking on 12Kh18N10T steel products
This article presents the results of tests evaluating the corrosion resistance of convex laser markings obtained by forming a relief pattern through melt control in the laser-impacted zone in the surface layer of 12Kh18N10T austenitic steel used to manufacture LNG logistics equipment (tanks and cylinders, tankers, road and rail tankers, pipelines, and pipeline fittings). The relevance of this work is due to the operation of these products in challenging atmospheric conditions typical of coastal zones and industrial regions, where exposure to chloride aerosols, condensates, and the acidic environment of marshy and peaty soils is possible. Tests were conducted on specimens with a relief pattern in the central portion and control specimens without laser processing. The relief was formed using a TurboMarker automated system with a fiber laser (λ = 1064 nm, τ = 100 ns, Pnom = 100 W) using specified scanning modes. Corrosion tests were conducted in a salt spray chamber under various conditions. Surface condition was assessed visually, gravimetrically, and by optical metallography. Electrochemical studies were also conducted, comparing the characteristics of the base metal and laser-treated area for corrosion potential, pitting potential, and pitting resistance. After testing, no corrosion or pitting products were detected on the samples, nor was any significant weight loss observed. The surface texture remained legible, which is important for traceability during maintenance and repair. Electrochemical data showed no signs of intense degradation of the passive state under the test conditions. The results confirm the feasibility of using convex laser marking as a durable identification method for LNG equipment components, resistant to external aggressive influences.The authors express their gratitude to the staff of Peter the Great St. Petersburg Polytechnic University for their assistance in conducting this research.
- 30 October 2025
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 10,p. 75-81
Effect of post-weld heat treatment of steel pipe billets on the performance of bored precast piles operated in permafrost soils
The development of hydrocarbon production sites in permafrost zones and the need to reduce costs require a more thorough study of the requirements for the materials and structures used. An analysis of regulatory and technical documentation revealed that some of these requirements are unreasonably high. Thus, SP 16.13330.2020 specifies that when manufacturing bored precast foundation piles, it is necessary to ensure an impact toughness level of welded joints obtained by high-frequency welding of at least 34 J/cm2 at a temperature of -60 °C. This requires extensive post-weld heat treatment of the pipes from which the piles are made, dramatically increasing the cost of the structure and leading to higher construction costs. It should be noted that GOST 20295, which is used to manufacture pipes for the piles, and similar regulatory and technical documents do not contain such requirements. An analysis of the mechanical properties and residual welding stresses in the pipes with and without heat treatment was conducted. Field tests of bored precast piles installed in the permafrost zone were also conducted. The conducted studies allow to conclude that the requirement for heat treatment of the pipes is excessive and should be eliminated.This work was carried out as part of a state assignment from the Ministry of Science and Higher Education of the Russian Federation (Topic No. FSEG-2024-0009: Development of models for the degradation of the performance properties of metallic and composite materials for construction in permafrost soils).
- 30 October 2025
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 10,p. 75-81
Effect of post-weld heat treatment of steel pipe billets on the performance of bored precast piles operated in permafrost soils
The development of hydrocarbon production sites in permafrost zones and the need to reduce costs require a more thorough study of the requirements for the materials and structures used. An analysis of regulatory and technical documentation revealed that some of these requirements are unreasonably high. Thus, SP 16.13330.2020 specifies that when manufacturing bored precast foundation piles, it is necessary to ensure an impact toughness level of welded joints obtained by high-frequency welding of at least 34 J/cm2 at a temperature of -60 °C. This requires extensive post-weld heat treatment of the pipes from which the piles are made, dramatically increasing the cost of the structure and leading to higher construction costs. It should be noted that GOST 20295, which is used to manufacture pipes for the piles, and similar regulatory and technical documents do not contain such requirements. An analysis of the mechanical properties and residual welding stresses in the pipes with and without heat treatment was conducted. Field tests of bored precast piles installed in the permafrost zone were also conducted. The conducted studies allow to conclude that the requirement for heat treatment of the pipes is excessive and should be eliminated.This work was carried out as part of a state assignment from the Ministry of Science and Higher Education of the Russian Federation (Topic No. FSEG-2024-0009: Development of models for the degradation of the performance properties of metallic and composite materials for construction in permafrost soils).
- 29 August 2025
- Published by Ore and Metals Publishing House in Tsvetnye Metally
- No. 8,p. 50-56
Application of plasma atomization for obtaining non-ferrous metal powders
The use of additive technologies in various industries using 3D-printers poses a number of challenges for materials research. It is important to know what initial metal powders are used to manufacture parts, assemblies, and even finished products. The wide range of mechanical engineering products raises the question of the possibility of using different grades of materials for additive technologies. Powder materials are subject to a number of strict requirements for chemical composition, absence of defects, and formation of various compounds on the surface, structure, and sphericity of the resulting particles. Depending on the 3D-printing method, it is necessary to ensure the requirements for the granulometric composition of the powders. The article considers the production of powder materials by plasma atomization, and provides recommended process parameters for the operation of the atomizer to obtain the maximum amount of powders of commercial fractions. It is shown that the occurrence of particle porosity can be affected by the quality of wire preparation, plasma-forming and shielding gases. The influence of various factors on obtaining a stable crystallization structure is considered. It has been established that control of temperature and flows of protective gas in the spray chamber allows to minimize the number of nano- and ultra-dispersed defects: micro-liquations and segregations in the volume of powder particles. The paper presents data confirming the possibility of using the method of plasma spraying of solid feedstocks to obtain high-quality powders for additive machines from alloys based on nickel, titanium, and copper. It has been shown that the obtained powders can be used to manufacture products by methods of direct or selective laser melting of parts, units, and mechanisms for various purposes.
- 29 August 2025
- Published by Ore and Metals Publishing House in Tsvetnye Metally
- No. 8,p. 50-56
Application of plasma atomization for obtaining non-ferrous metal powders
The use of additive technologies in various industries using 3D-printers poses a number of challenges for materials research. It is important to know what initial metal powders are used to manufacture parts, assemblies, and even finished products. The wide range of mechanical engineering products raises the question of the possibility of using different grades of materials for additive technologies. Powder materials are subject to a number of strict requirements for chemical composition, absence of defects, and formation of various compounds on the surface, structure, and sphericity of the resulting particles. Depending on the 3D-printing method, it is necessary to ensure the requirements for the granulometric composition of the powders. The article considers the production of powder materials by plasma atomization, and provides recommended process parameters for the operation of the atomizer to obtain the maximum amount of powders of commercial fractions. It is shown that the occurrence of particle porosity can be affected by the quality of wire preparation, plasma-forming and shielding gases. The influence of various factors on obtaining a stable crystallization structure is considered. It has been established that control of temperature and flows of protective gas in the spray chamber allows to minimize the number of nano- and ultra-dispersed defects: micro-liquations and segregations in the volume of powder particles. The paper presents data confirming the possibility of using the method of plasma spraying of solid feedstocks to obtain high-quality powders for additive machines from alloys based on nickel, titanium, and copper. It has been shown that the obtained powders can be used to manufacture products by methods of direct or selective laser melting of parts, units, and mechanisms for various purposes.
- 7 November 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (7) , 961-969
Influence of drill pipe manufacturing technology on fracture mechanisms and fatigue properties
- 7 November 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (7) , 961-969
Influence of drill pipe manufacturing technology on fracture mechanisms and fatigue properties
- 30 September 2024
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 9,p. 4-8
A new look at the iron-carbon diagram of D. K. Chernov
It is difficult to overestimate the significance of the Fe–C phase diagram, the construction of which was initiated by D. K. Chernov, which allowed to open new boundaries in understanding the properties of iron-based alloys. At the same time, anomalies in properties and the lack of connection between them and the structure of alloy mixtures and the phase diagram have been known for about a century, but have not been explained. A. A. Bochvar, studying the properties of alloy mixtures consisting of obviously pure components, concluded: “As it turned out, there is no unambiguous relationship between composition and properties at all.” I. I. Kornilov came to the same conclusion: “But it is difficult to establish any strict connection between hardness and the phase diagram.” N. I. Belyaev and N. T. Gudtsov noted much more sharply: “The apparent elastic limit has no connection with the structure of steel.” E. Gudremon, hiding an obvious anomaly (the maximum yield strength), drew a curve past the experimental point at ~0.5 % C. The maximum yield strength of annealed steels at ~0.5 % C was shown by P. Obergoffer in 1915, but left without comment. The analysis of the Fe – C phase diagram is performed taking into account three verticals plotted by D. K. Chernov in 1916, which were not taken into account in subsequent editions of the diagram. N.S. Kurnakov’s rule connects changes in the properties of alloys with the type of phase diagram, but does not explain numerous anomalies in the physical and mechanical properties of alloys. In this regard, a new approach to the analysis of the phase diagram is proposed, taking into account the three verticals of D.K. Chernov and the lines of the phase diagram taking into account concentration dependencies and qualitative intervals of crystallization (recrystallization). Based on the established numerous anomalies in the physical and mechanical properties of melts, austenite, martensite and ferrite-cementite mixture, intermediate phases (~Fe42C, ~Fe24C, ~Fe10C) are declared, allowing a new look at the diagram discovered more than 100 years ago. The intermediate phases declared in the article can be used to explain the anomalies of the physical and mechanical properties of industrially used steels
- 30 September 2024
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 9,p. 4-8
A new look at the iron-carbon diagram of D. K. Chernov
It is difficult to overestimate the significance of the Fe–C phase diagram, the construction of which was initiated by D. K. Chernov, which allowed to open new boundaries in understanding the properties of iron-based alloys. At the same time, anomalies in properties and the lack of connection between them and the structure of alloy mixtures and the phase diagram have been known for about a century, but have not been explained. A. A. Bochvar, studying the properties of alloy mixtures consisting of obviously pure components, concluded: “As it turned out, there is no unambiguous relationship between composition and properties at all.” I. I. Kornilov came to the same conclusion: “But it is difficult to establish any strict connection between hardness and the phase diagram.” N. I. Belyaev and N. T. Gudtsov noted much more sharply: “The apparent elastic limit has no connection with the structure of steel.” E. Gudremon, hiding an obvious anomaly (the maximum yield strength), drew a curve past the experimental point at ~0.5 % C. The maximum yield strength of annealed steels at ~0.5 % C was shown by P. Obergoffer in 1915, but left without comment. The analysis of the Fe – C phase diagram is performed taking into account three verticals plotted by D. K. Chernov in 1916, which were not taken into account in subsequent editions of the diagram. N.S. Kurnakov’s rule connects changes in the properties of alloys with the type of phase diagram, but does not explain numerous anomalies in the physical and mechanical properties of alloys. In this regard, a new approach to the analysis of the phase diagram is proposed, taking into account the three verticals of D.K. Chernov and the lines of the phase diagram taking into account concentration dependencies and qualitative intervals of crystallization (recrystallization). Based on the established numerous anomalies in the physical and mechanical properties of melts, austenite, martensite and ferrite-cementite mixture, intermediate phases (~Fe42C, ~Fe24C, ~Fe10C) are declared, allowing a new look at the diagram discovered more than 100 years ago. The intermediate phases declared in the article can be used to explain the anomalies of the physical and mechanical properties of industrially used steels
- 30 September 2024
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 9,p. 37-43
Causes of accelerated failure of excavator bucket teeth crowns when operating in Arctic regions
The mining industry is gradually moving to the Arctic region characterized by permafrost and permafrost soils. Excavation of rocks in these regions is hampered by increased rock strength due to ice freezing of rock pieces after stripping works and requires a new approach to the production of quick-change tools for excavator and loader buckets. The paper analyzes the causes of accelerated failure of excavator bucket crowns after operation in winter in the northern regions of the country; it is shown that the main causes of their accelerated failure are casting defects and insufficient cold resistance of crown material. Hot foundry cracks and large non-metallic inclusions are the initiators of accelerated failure, fatigue cracks and cold brittle cracks develop on their basis during operation. Insufficient cold resistance of steel grades used for these regions and their heat treatment modes have been confirmed, which leads to the development of brittle fracture cracks. It is established that in order to increase the serviceability of excavator crown metal operating in cold climate conditions it is necessary to modify the chemical composition of steel aimed at increasing its cold resistance while maintaining the level of strength and hardness, the main directions of steel composition modification are determined.The study was supported by the Russian Science Foundation grant No. 24-29-00713, https://rscf.ru/project/24-29-00713/.
- 30 September 2024
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 9,p. 37-43
Causes of accelerated failure of excavator bucket teeth crowns when operating in Arctic regions
The mining industry is gradually moving to the Arctic region characterized by permafrost and permafrost soils. Excavation of rocks in these regions is hampered by increased rock strength due to ice freezing of rock pieces after stripping works and requires a new approach to the production of quick-change tools for excavator and loader buckets. The paper analyzes the causes of accelerated failure of excavator bucket crowns after operation in winter in the northern regions of the country; it is shown that the main causes of their accelerated failure are casting defects and insufficient cold resistance of crown material. Hot foundry cracks and large non-metallic inclusions are the initiators of accelerated failure, fatigue cracks and cold brittle cracks develop on their basis during operation. Insufficient cold resistance of steel grades used for these regions and their heat treatment modes have been confirmed, which leads to the development of brittle fracture cracks. It is established that in order to increase the serviceability of excavator crown metal operating in cold climate conditions it is necessary to modify the chemical composition of steel aimed at increasing its cold resistance while maintaining the level of strength and hardness, the main directions of steel composition modification are determined.The study was supported by the Russian Science Foundation grant No. 24-29-00713, https://rscf.ru/project/24-29-00713/.
- 29 February 2024
- Published by Ore and Metals Publishing House in Tsvetnye Metally
- No. 2,p. 53-59
A relationship between abnormal electrical properties in non-ferrous alloys and phase equilibrium diagrams
Given the fact that identifying the cause-and-effect mechanisms behind abnormal properties in materials is of enormous importance for science and practical sphere, the authors of this paper propose an approach that allows to establish the relationship between the changing electrical properties and the nanoparticles of intermediate phases forming in non-ferrous metal alloys. A KΔ criterion is proposed that allows to evaluate a possible formation of nanoparticles of chemical compounds (intermediate phases) which significantly influence transformations in the fine structure. This helps relate the extremums on the curves of electrical properties (such as electric conductivity, specific electrical resistance, electrical resistivity, temperature coefficient of electrical resistance, thermoelectromotive force), which can hardly be explained, to the phase equilibrium diagrams of commercial non-ferrous alloys. It becomes possible to consider the phase equilibrium diagram taking into account the developed KΔ criterion, which allows to predict the formation of nanoparticles of intermediate phases and, as a consequence, changes in electrical properties in the systems (Pt – Ag, Al – Fe, Bi – Pb, Al – Zr, Cu – Zn) of non-ferrous alloys. The developed KΔ criterion enables to determine the causes of: maximum electrical resistivity and its temperature coefficient of silver-platinum alloys; unchangeable electrical resistivity in the concentration range (24–32%(at.) Fe) of aluminium-iron alloys; the spike in conductivity and absolute maximum of thermoelectromotive force of bismuth-lead alloys; maximum specific resisti vity of aluminium-zirconium alloys; unchangeable conductivity and temperature coefficient of electrical resistance of copper-zinc alloys.
- 29 February 2024
- Published by Ore and Metals Publishing House in Tsvetnye Metally
- No. 2,p. 53-59
A relationship between abnormal electrical properties in non-ferrous alloys and phase equilibrium diagrams
Given the fact that identifying the cause-and-effect mechanisms behind abnormal properties in materials is of enormous importance for science and practical sphere, the authors of this paper propose an approach that allows to establish the relationship between the changing electrical properties and the nanoparticles of intermediate phases forming in non-ferrous metal alloys. A KΔ criterion is proposed that allows to evaluate a possible formation of nanoparticles of chemical compounds (intermediate phases) which significantly influence transformations in the fine structure. This helps relate the extremums on the curves of electrical properties (such as electric conductivity, specific electrical resistance, electrical resistivity, temperature coefficient of electrical resistance, thermoelectromotive force), which can hardly be explained, to the phase equilibrium diagrams of commercial non-ferrous alloys. It becomes possible to consider the phase equilibrium diagram taking into account the developed KΔ criterion, which allows to predict the formation of nanoparticles of intermediate phases and, as a consequence, changes in electrical properties in the systems (Pt – Ag, Al – Fe, Bi – Pb, Al – Zr, Cu – Zn) of non-ferrous alloys. The developed KΔ criterion enables to determine the causes of: maximum electrical resistivity and its temperature coefficient of silver-platinum alloys; unchangeable electrical resistivity in the concentration range (24–32%(at.) Fe) of aluminium-iron alloys; the spike in conductivity and absolute maximum of thermoelectromotive force of bismuth-lead alloys; maximum specific resisti vity of aluminium-zirconium alloys; unchangeable conductivity and temperature coefficient of electrical resistance of copper-zinc alloys.
- 1 September 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (5-6) , 644-651
Investigation of Material Properties for Cryogenic Products, Produced by Additive Manufacturing Techniques
- 1 September 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (5-6) , 644-651
Investigation of Material Properties for Cryogenic Products, Produced by Additive Manufacturing Techniques