Lu Jin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lu Jin has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Yu Liu
Dalian Jiaotong University
2 shared publications - Dapeng Yang
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication - Fujian Ma
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication - Guotao Ru
Xi’an Railway Signal Co., Ltd., Xi’an 710104, China
1 shared publication - Jian Yin
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication - Jian Yin
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication
Latest Publications
- Open Access
Simulation Study on the Evolution Behaviour of Endogenous Third Bodies in the Rough Friction Interface During Braking and Their Impact
During braking, high-power wind turbine disc brake friction pairs experience thermo-mechanical interactions at the interface, which lead to both physical and chemical changes. The friction interface features asperities and embedded hard particles within the substrate. Wear debris from these asperities or dislodged hard particles accumulates at the interface, continuing to participate in the friction process—a phenomenon known as the “endogenous third body”. Throughout braking, the microscopic morphology and contact conditions of the interface evolve dynamically. The stress–strain distribution and vibration behaviour of the friction system, influenced by the endogenous third body, also vary with braking parameters. This study employs the W-M fractal theory to develop a finite element model of a rough friction interface containing hard-particle endogenous third bodies. The model is validated through experimental testing. Based on the performance test parameters of high-power wind turbine disc brakes, a simulation is conducted to analyse the contact friction process involving the endogenous third body at the rough interface between the brake disc and brake pad. The simulation reproduces the formation process of the endogenous third body and reveals its evolutionary stages, including “ploughing”, “gap-filling”, and “aggregation”. Additionally, the study examines changes in the internal stress–strain and vibration states of the friction system under varying braking speeds (5 m/s to 35 m/s) and braking loads (3 MPa to 6 MPa). The findings demonstrate how different braking parameters influence the friction system containing the endogenous third body. The results showed that when the braking speeds were 5 m/s, 15 m/s, 25 m/s, and 35 m/s, and the braking load was 6 MPa, the average amplitude of the brake pads was the smallest, at 0.017 mm, 0.021 mm, 0.025 mm, and 0.020 mm, respectively. This research provides valuable insights into the three-body contact friction mechanism at the micro-braking interface, the formation of composite material third bodies, and the role of wear-stage third bodies in affecting the friction interface.
Open AccessSimulation Study on the Evolution Behaviour of Endogenous Third Bodies in the Rough Friction Interface During Braking and Their Impact
During braking, high-power wind turbine disc brake friction pairs experience thermo-mechanical interactions at the interface, which lead to both physical and chemical changes. The friction interface features asperities and embedded hard particles within the substrate. Wear debris from these asperities or dislodged hard particles accumulates at the interface, continuing to participate in the friction process—a phenomenon known as the “endogenous third body”. Throughout braking, the microscopic morphology and contact conditions of the interface evolve dynamically. The stress–strain distribution and vibration behaviour of the friction system, influenced by the endogenous third body, also vary with braking parameters. This study employs the W-M fractal theory to develop a finite element model of a rough friction interface containing hard-particle endogenous third bodies. The model is validated through experimental testing. Based on the performance test parameters of high-power wind turbine disc brakes, a simulation is conducted to analyse the contact friction process involving the endogenous third body at the rough interface between the brake disc and brake pad. The simulation reproduces the formation process of the endogenous third body and reveals its evolutionary stages, including “ploughing”, “gap-filling”, and “aggregation”. Additionally, the study examines changes in the internal stress–strain and vibration states of the friction system under varying braking speeds (5 m/s to 35 m/s) and braking loads (3 MPa to 6 MPa). The findings demonstrate how different braking parameters influence the friction system containing the endogenous third body. The results showed that when the braking speeds were 5 m/s, 15 m/s, 25 m/s, and 35 m/s, and the braking load was 6 MPa, the average amplitude of the brake pads was the smallest, at 0.017 mm, 0.021 mm, 0.025 mm, and 0.020 mm, respectively. This research provides valuable insights into the three-body contact friction mechanism at the micro-braking interface, the formation of composite material third bodies, and the role of wear-stage third bodies in affecting the friction interface.
- Open Access
Study on the Influence Law of Micro-Scale Abrasive Wear on a Wind Turbine Brake Pad
The hard particles in the copper-based powder metallurgic material of a brake pad for a wind turbine brake falls off and presses into the surface of the brake disc to form abrasive particles under high-speed and heavy-load working conditions. The presence of abrasive particles will produce abrasive wear with micro-scratch and micro-scribe on the copper-based material of the brake pad. The critical scratch depth effect in the abrasive wear process is proposed based on the critical depth effect of the metal removal process at the micro-scale. The abrasive wear is divided into two types: scratch wear and scratch wear, which is proposed according to the comparison of the actual scratch depth and the critical scratch depth. The range of braking speeds and friction coefficients in abrasive wear is determined by the recommended parameters of the disc brake. The ABAQUS2020 software is used to simulate and analyze the micro-scale abrasive wear of a brake pad. The brake strain/stress curves of the brake pad under different brake speeds and friction coefficients are compared and analyzed for two abrasive wear types based on the range of braking parameters, and the key factors affecting abrasive wear are proposed.
Open AccessStudy on the Influence Law of Micro-Scale Abrasive Wear on a Wind Turbine Brake Pad
The hard particles in the copper-based powder metallurgic material of a brake pad for a wind turbine brake falls off and presses into the surface of the brake disc to form abrasive particles under high-speed and heavy-load working conditions. The presence of abrasive particles will produce abrasive wear with micro-scratch and micro-scribe on the copper-based material of the brake pad. The critical scratch depth effect in the abrasive wear process is proposed based on the critical depth effect of the metal removal process at the micro-scale. The abrasive wear is divided into two types: scratch wear and scratch wear, which is proposed according to the comparison of the actual scratch depth and the critical scratch depth. The range of braking speeds and friction coefficients in abrasive wear is determined by the recommended parameters of the disc brake. The ABAQUS2020 software is used to simulate and analyze the micro-scale abrasive wear of a brake pad. The brake strain/stress curves of the brake pad under different brake speeds and friction coefficients are compared and analyzed for two abrasive wear types based on the range of braking parameters, and the key factors affecting abrasive wear are proposed.