Anar Kenzhebekova
Research Subjects
Anar Kenzhebekova has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Altynsary Bakirov
Department of Metallurgy, Faculty of Engineering, Toraighyrov University, Pavlodar 140008, Kazakhstan
4 shared publications - A. K. Zhunusova2 shared publications
- Ablay Zhunusov
Department of Metallurgy, Toraighyrov University, Pavlodar 140008, Kazakhstan
2 shared publications - Renat Tyulyubayev
Department of Metallurgy, Toraighyrov University, Pavlodar 140008, Kazakhstan
2 shared publications Ablay Zhunusov
1 shared publicationAygul Zhunusova
1 shared publication
Latest Publications
- 31 March 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 1, 2026,p. 258-270
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF PELLETS OBTAINED FROM ALUMINUM SLAG
This paper examines the physicochemical and mineralogical properties of pellets produced from secondary aluminum slags with the addition of silica-enriched aspiration dust from ferroalloy production. To incorporate finely dispersed industrial waste into metallurgical processing, a pelletizing method was applied in a disk granulator using an aqueous lignosulfonate solution as a binder. The resulting pellets were subjected to high-temperature firing at temperatures of 600, 800, and 1000 °C. The phase and mineralogical composition were studied using X-ray diffraction and petrographic analysis, and the microstructure was analyzed using electron microscopy. It was found that increasing the firing temperature intensifies solid-phase interactions and forms calcium silicate and aluminosilicate phases, such as wollastonite, dicalcium silicate, and mullite. The introduction of aspiration dust with a high SiO₂ content helps reduce the sintering onset temperature and strengthen the pellet structure by forming a binding silicate matrix. It has been shown that optimizing the composition and firing temperature allows for the production of heat-resistant and mechanically strong pellets, promising for use in processes for producing ferrosilicon with increased aluminum content. Keywords: Aluminum slag, pellets, pelletizing, X-ray phase analysis, ferrosilicon.
- 31 March 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 1, 2026,p. 258-270
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF PELLETS OBTAINED FROM ALUMINUM SLAG
This paper examines the physicochemical and mineralogical properties of pellets produced from secondary aluminum slags with the addition of silica-enriched aspiration dust from ferroalloy production. To incorporate finely dispersed industrial waste into metallurgical processing, a pelletizing method was applied in a disk granulator using an aqueous lignosulfonate solution as a binder. The resulting pellets were subjected to high-temperature firing at temperatures of 600, 800, and 1000 °C. The phase and mineralogical composition were studied using X-ray diffraction and petrographic analysis, and the microstructure was analyzed using electron microscopy. It was found that increasing the firing temperature intensifies solid-phase interactions and forms calcium silicate and aluminosilicate phases, such as wollastonite, dicalcium silicate, and mullite. The introduction of aspiration dust with a high SiO₂ content helps reduce the sintering onset temperature and strengthen the pellet structure by forming a binding silicate matrix. It has been shown that optimizing the composition and firing temperature allows for the production of heat-resistant and mechanically strong pellets, promising for use in processes for producing ferrosilicon with increased aluminum content. Keywords: Aluminum slag, pellets, pelletizing, X-ray phase analysis, ferrosilicon.
- 30 December 2025
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 4, 2025,p. 260-272
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF GRANULES OBTAINED FROM ALUMINUM SLAGS
This article presents the studies of the physicochemical properties of granules obtained by granulation of aluminum slags. During the studies, the granules were subjected to hardening firing at high temperatures to understand the chemistry of the process. To study the physicochemical properties, samples of granules obtained from aluminum slags were prepared, which were subjected to microanalysis by scanning electron microscopy, X-ray phase analysis and derivatographic studies. The studies showed that the main phases in the granules are Al2MgO4, Al5,65Mg2,39O10Si1,45, MgO3Si, Al2,4O4,8Si0,6, Al2O3. The main part of the studied granules is represented by spinel, mullite, aluminum oxide, sapphirine. Moreover, spinels in the phase composition of sample №. 1 amounted to 25.4 %, sapphirine 26.0 %, aluminum oxides 25 % and mullite accounts for 11.7 5, the rest is MgO3Si (11.9 %). The theoretical temperature of the reduction of the main element of silicon by carbon is 1669 °C, and the complete destruction of mullite is achieved above 1500 °C. Therefore, granules obtained from aluminum slags are quite suitable for use as a batch in the production of ferrosilicon with aluminum. Keywords: Aluminum slag, granules, aluminum oxide, high-temperature firing, derivatogram.
- 30 December 2025
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 4, 2025,p. 260-272
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF GRANULES OBTAINED FROM ALUMINUM SLAGS
This article presents the studies of the physicochemical properties of granules obtained by granulation of aluminum slags. During the studies, the granules were subjected to hardening firing at high temperatures to understand the chemistry of the process. To study the physicochemical properties, samples of granules obtained from aluminum slags were prepared, which were subjected to microanalysis by scanning electron microscopy, X-ray phase analysis and derivatographic studies. The studies showed that the main phases in the granules are Al2MgO4, Al5,65Mg2,39O10Si1,45, MgO3Si, Al2,4O4,8Si0,6, Al2O3. The main part of the studied granules is represented by spinel, mullite, aluminum oxide, sapphirine. Moreover, spinels in the phase composition of sample №. 1 amounted to 25.4 %, sapphirine 26.0 %, aluminum oxides 25 % and mullite accounts for 11.7 5, the rest is MgO3Si (11.9 %). The theoretical temperature of the reduction of the main element of silicon by carbon is 1669 °C, and the complete destruction of mullite is achieved above 1500 °C. Therefore, granules obtained from aluminum slags are quite suitable for use as a batch in the production of ferrosilicon with aluminum. Keywords: Aluminum slag, granules, aluminum oxide, high-temperature firing, derivatogram.
- Open Access
- 11 November 2025
- Published by Elsevier in Journal of Alloys and Metallurgical Systems
- Vol. 12
Study of the use of aluminium-containing waste in ferrosilicon production
- 11 November 2025
- Published by Elsevier in Journal of Alloys and Metallurgical Systems
- Vol. 12
Open AccessStudy of the use of aluminium-containing waste in ferrosilicon production
- 30 September 2024
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 3.2024,p. 187-199
DETERMINATION OF OPTIMAL PARAMETERS OF SINTERING OF ROLLING SCALE
This article presents the results of studies conducted to determine the optimal parameters of sintering of rolled scale in a mixture with iron-containing steelmaking waste. The conducted studies of sintering of rolled scale have shown that the gas permeability of the charge depends on a number of physical properties, the size and shape of the grains, the amount of return, the height of the charge layer, and the moisture content of the charge. The initial gas permeability strongly depends on the degree of humidification of the agglomeration charge, especially when sintering small classes of materials under study. The maximum gas permeability of the charge is ensured with an optimal granulometric composition of the charge, which is characterized by an average equivalent diameter: the higher this indicator, the higher the gas permeability of the charge. The value of the surface tension reaches its maximum at a certain moisture content of the charge, which is the optimal moisture for this charge. By increasing the amount of return during agglomeration, the vertical sintering rate increases and the quality of the agglomerate improves. These factors lead to an increase in the productivity of sintering plants. According to the results of the study, the optimal parameters of the sintering sintering process of rolled scale in a mixture with iron-containing steelmaking waste were worked out. It is established that the optimal amount of return is the use of 20 % of the mass of the sintering charge at the optimal height of the sintered layer of 300 mm. As a result of the conducted research, the following optimal indicators were achieved: mechanical strength – 70.2 %, sintering rate – 28.7 mm/min, specific productivity – 1.75 t/m2·hour. Keywords: Rolling scale, agglomeration, optimal parameters, sintering, return, layer height.
- 30 September 2024
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 3.2024,p. 187-199
DETERMINATION OF OPTIMAL PARAMETERS OF SINTERING OF ROLLING SCALE
This article presents the results of studies conducted to determine the optimal parameters of sintering of rolled scale in a mixture with iron-containing steelmaking waste. The conducted studies of sintering of rolled scale have shown that the gas permeability of the charge depends on a number of physical properties, the size and shape of the grains, the amount of return, the height of the charge layer, and the moisture content of the charge. The initial gas permeability strongly depends on the degree of humidification of the agglomeration charge, especially when sintering small classes of materials under study. The maximum gas permeability of the charge is ensured with an optimal granulometric composition of the charge, which is characterized by an average equivalent diameter: the higher this indicator, the higher the gas permeability of the charge. The value of the surface tension reaches its maximum at a certain moisture content of the charge, which is the optimal moisture for this charge. By increasing the amount of return during agglomeration, the vertical sintering rate increases and the quality of the agglomerate improves. These factors lead to an increase in the productivity of sintering plants. According to the results of the study, the optimal parameters of the sintering sintering process of rolled scale in a mixture with iron-containing steelmaking waste were worked out. It is established that the optimal amount of return is the use of 20 % of the mass of the sintering charge at the optimal height of the sintered layer of 300 mm. As a result of the conducted research, the following optimal indicators were achieved: mechanical strength – 70.2 %, sintering rate – 28.7 mm/min, specific productivity – 1.75 t/m2·hour. Keywords: Rolling scale, agglomeration, optimal parameters, sintering, return, layer height.