Altynsary Bakirov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Altynsary Bakirov has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Ablay Zhunusov
Department of Metallurgy, Toraighyrov University, Pavlodar 140008, Kazakhstan
4 shared publications - Anar Kenzhebekova4 shared publications
- Renat Tyulyubayev
Department of Metallurgy, Toraighyrov University, Pavlodar 140008, Kazakhstan
4 shared publications - A. K. Zhunusova3 shared publications
Ablay Zhunusov
2 shared publications- O. V. Zayakin
Institute of Metallurgy, Ural Branch of the Russian Academy of Sciences, Ekaterinburg 620016, Russia
2 shared publications
Latest Publications
- Open Access
Production of Aluminum Hydroxide from Aluminate Solution Obtained by Red Mud Sinter Processing via Carbonation
This study investigated the processing of an aluminate solution obtained by laboratory leaching of industrial red mud sinter, followed by sequential silica removal and aluminum hydroxide precipitation through carbonation. Autoclave treatment at 145 °C for 60 min, followed by treatment with CaO (8 g/dm3) at 90 °C for 120 min, reduced the SiO2 concentration from 1.10 to 0.03 g/dm3 and increased the silica modulus of the solution from 31.1 to 1076. The effects of solution density (1.10–1.40 g/cm3) and temperature (20–90 °C) on carbonation efficiency were evaluated in terms of Al2O3 recovery and the phase composition of the precipitate. At a solution density of 1.35 g/cm3 and a temperature of 90 °C, Al2O3 recovery reached 90.1%, while the resulting product contained 98.3% gibbsite, Al(OH)3. Increasing the solution density to 1.40 g/cm3 decreased Al2O3 recovery to 47.9% and promoted the formation of NaAlCO3(OH)2, thereby defining the upper limit of the rational solution-density range. The obtained aluminum hydroxide exhibited an average particle size of 46.3 μm. The results clarify the effect of alkaline solution composition on phase formation during carbonation and establish the conditions required to obtain a predominantly gibbsite product.
Open AccessProduction of Aluminum Hydroxide from Aluminate Solution Obtained by Red Mud Sinter Processing via Carbonation
This study investigated the processing of an aluminate solution obtained by laboratory leaching of industrial red mud sinter, followed by sequential silica removal and aluminum hydroxide precipitation through carbonation. Autoclave treatment at 145 °C for 60 min, followed by treatment with CaO (8 g/dm3) at 90 °C for 120 min, reduced the SiO2 concentration from 1.10 to 0.03 g/dm3 and increased the silica modulus of the solution from 31.1 to 1076. The effects of solution density (1.10–1.40 g/cm3) and temperature (20–90 °C) on carbonation efficiency were evaluated in terms of Al2O3 recovery and the phase composition of the precipitate. At a solution density of 1.35 g/cm3 and a temperature of 90 °C, Al2O3 recovery reached 90.1%, while the resulting product contained 98.3% gibbsite, Al(OH)3. Increasing the solution density to 1.40 g/cm3 decreased Al2O3 recovery to 47.9% and promoted the formation of NaAlCO3(OH)2, thereby defining the upper limit of the rational solution-density range. The obtained aluminum hydroxide exhibited an average particle size of 46.3 μm. The results clarify the effect of alkaline solution composition on phase formation during carbonation and establish the conditions required to obtain a predominantly gibbsite product.
- 30 June 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 2, 2026,p. 325-335
LARGE-LABORATORY SMELTING OF FERROSILICON IN AN ORE-THERMAL FURNACE
This paper presents the results of large-scale laboratory ferrosilicon smelting in an 80 kVA ore-thermal furnace using recycled man-made materials. The possibility of partially replacing steel chips with iron ore agglomerate obtained from ferrous sands of alumina production, as well as the use of aluminum slag-based pellets, is investigated. The influence of the chemical composition of the charge components on the physicochemical and electrical characteristics of the smelting process is determined. It is shown that increased SiO2 and Al2O3 contents in the pellets promote the formation of silicate melts, stabilization of the slag phase, and improved conditions for silicon reduction. The identified kinetic patterns allow for temperature optimization. The developed technology also contributes to a significant reduction in energy consumption. It is determined that the use of recycled resources reduces the content of harmful impurities in the alloy and reduces production costs. The obtained results confirm the technological efficiency and environmental feasibility of using complex man-made materials in ferrosilicon smelting. Keywords: Ferrosilicon, ore-thermal furnace, man-made waste, iron ore agglomerate, ferrous sands, electrical resistanceе.
- 30 June 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 2, 2026,p. 325-335
LARGE-LABORATORY SMELTING OF FERROSILICON IN AN ORE-THERMAL FURNACE
This paper presents the results of large-scale laboratory ferrosilicon smelting in an 80 kVA ore-thermal furnace using recycled man-made materials. The possibility of partially replacing steel chips with iron ore agglomerate obtained from ferrous sands of alumina production, as well as the use of aluminum slag-based pellets, is investigated. The influence of the chemical composition of the charge components on the physicochemical and electrical characteristics of the smelting process is determined. It is shown that increased SiO2 and Al2O3 contents in the pellets promote the formation of silicate melts, stabilization of the slag phase, and improved conditions for silicon reduction. The identified kinetic patterns allow for temperature optimization. The developed technology also contributes to a significant reduction in energy consumption. It is determined that the use of recycled resources reduces the content of harmful impurities in the alloy and reduces production costs. The obtained results confirm the technological efficiency and environmental feasibility of using complex man-made materials in ferrosilicon smelting. Keywords: Ferrosilicon, ore-thermal furnace, man-made waste, iron ore agglomerate, ferrous sands, electrical resistanceе.
- Open Access
The Influence of High-Temperature Roasting on the Phase Composition of Pellets Based on Aluminum Slags and Their Testing in the Smelting of Ferrosilicon
This paper examines a resource-saving technology for ferrosilicon smelting using industrial waste, specifically aluminum slag and aspiration dust from ferroalloy production. A technological approach is proposed based on the preliminary pelletization of finely dispersed aluminum slag to improve the physicochemical properties of the charge materials and ensure their efficient use in the metallurgical process. Pellets were produced by granulation in a disk granulator using a lignosulfonate binder, followed by drying and high-temperature firing in the temperature range of 600–800 °C. Microstructural and energy-dispersive analysis revealed the formation of a stable aluminosilicate matrix, represented predominantly by mullite-like phases, ferrosilicate inclusions, and calcium–magnesium silicates. The formation of these phases contributes to the strengthening of the pellet structure and the formation of intergranular bonds during heat treatment. Experimental ferrosilicon smelting was conducted in a laboratory ore-thermal electric arc furnace. The results demonstrated a stable electrothermal smelting regime, satisfactory charge layer gas permeability, and effective reduction processes. The resulting alloy corresponds to FS-45 ferrosilicon grade with a silicon content of approximately 48%. It was established that aluminum slag-based pellets actively participate in the formation of an aluminosilicate slag system of the SiO2-Al2O3-CaO-MgO type, ensuring favorable slag physicochemical properties and efficient separation of the metallic and slag phases. The proposed approach enables the incorporation of industrial waste into metallurgical production, reducing the environmental impact, and increasing the resource efficiency of silicon ferroalloy production processes.
Open AccessThe Influence of High-Temperature Roasting on the Phase Composition of Pellets Based on Aluminum Slags and Their Testing in the Smelting of Ferrosilicon
This paper examines a resource-saving technology for ferrosilicon smelting using industrial waste, specifically aluminum slag and aspiration dust from ferroalloy production. A technological approach is proposed based on the preliminary pelletization of finely dispersed aluminum slag to improve the physicochemical properties of the charge materials and ensure their efficient use in the metallurgical process. Pellets were produced by granulation in a disk granulator using a lignosulfonate binder, followed by drying and high-temperature firing in the temperature range of 600–800 °C. Microstructural and energy-dispersive analysis revealed the formation of a stable aluminosilicate matrix, represented predominantly by mullite-like phases, ferrosilicate inclusions, and calcium–magnesium silicates. The formation of these phases contributes to the strengthening of the pellet structure and the formation of intergranular bonds during heat treatment. Experimental ferrosilicon smelting was conducted in a laboratory ore-thermal electric arc furnace. The results demonstrated a stable electrothermal smelting regime, satisfactory charge layer gas permeability, and effective reduction processes. The resulting alloy corresponds to FS-45 ferrosilicon grade with a silicon content of approximately 48%. It was established that aluminum slag-based pellets actively participate in the formation of an aluminosilicate slag system of the SiO2-Al2O3-CaO-MgO type, ensuring favorable slag physicochemical properties and efficient separation of the metallic and slag phases. The proposed approach enables the incorporation of industrial waste into metallurgical production, reducing the environmental impact, and increasing the resource efficiency of silicon ferroalloy production processes.
- 31 March 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 1, 2026,p. 258-270
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF PELLETS OBTAINED FROM ALUMINUM SLAG
This paper examines the physicochemical and mineralogical properties of pellets produced from secondary aluminum slags with the addition of silica-enriched aspiration dust from ferroalloy production. To incorporate finely dispersed industrial waste into metallurgical processing, a pelletizing method was applied in a disk granulator using an aqueous lignosulfonate solution as a binder. The resulting pellets were subjected to high-temperature firing at temperatures of 600, 800, and 1000 °C. The phase and mineralogical composition were studied using X-ray diffraction and petrographic analysis, and the microstructure was analyzed using electron microscopy. It was found that increasing the firing temperature intensifies solid-phase interactions and forms calcium silicate and aluminosilicate phases, such as wollastonite, dicalcium silicate, and mullite. The introduction of aspiration dust with a high SiO₂ content helps reduce the sintering onset temperature and strengthen the pellet structure by forming a binding silicate matrix. It has been shown that optimizing the composition and firing temperature allows for the production of heat-resistant and mechanically strong pellets, promising for use in processes for producing ferrosilicon with increased aluminum content. Keywords: Aluminum slag, pellets, pelletizing, X-ray phase analysis, ferrosilicon.
- 31 March 2026
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 1, 2026,p. 258-270
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF PELLETS OBTAINED FROM ALUMINUM SLAG
This paper examines the physicochemical and mineralogical properties of pellets produced from secondary aluminum slags with the addition of silica-enriched aspiration dust from ferroalloy production. To incorporate finely dispersed industrial waste into metallurgical processing, a pelletizing method was applied in a disk granulator using an aqueous lignosulfonate solution as a binder. The resulting pellets were subjected to high-temperature firing at temperatures of 600, 800, and 1000 °C. The phase and mineralogical composition were studied using X-ray diffraction and petrographic analysis, and the microstructure was analyzed using electron microscopy. It was found that increasing the firing temperature intensifies solid-phase interactions and forms calcium silicate and aluminosilicate phases, such as wollastonite, dicalcium silicate, and mullite. The introduction of aspiration dust with a high SiO₂ content helps reduce the sintering onset temperature and strengthen the pellet structure by forming a binding silicate matrix. It has been shown that optimizing the composition and firing temperature allows for the production of heat-resistant and mechanically strong pellets, promising for use in processes for producing ferrosilicon with increased aluminum content. Keywords: Aluminum slag, pellets, pelletizing, X-ray phase analysis, ferrosilicon.
- 30 December 2025
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 4, 2025,p. 260-272
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF GRANULES OBTAINED FROM ALUMINUM SLAGS
This article presents the studies of the physicochemical properties of granules obtained by granulation of aluminum slags. During the studies, the granules were subjected to hardening firing at high temperatures to understand the chemistry of the process. To study the physicochemical properties, samples of granules obtained from aluminum slags were prepared, which were subjected to microanalysis by scanning electron microscopy, X-ray phase analysis and derivatographic studies. The studies showed that the main phases in the granules are Al2MgO4, Al5,65Mg2,39O10Si1,45, MgO3Si, Al2,4O4,8Si0,6, Al2O3. The main part of the studied granules is represented by spinel, mullite, aluminum oxide, sapphirine. Moreover, spinels in the phase composition of sample №. 1 amounted to 25.4 %, sapphirine 26.0 %, aluminum oxides 25 % and mullite accounts for 11.7 5, the rest is MgO3Si (11.9 %). The theoretical temperature of the reduction of the main element of silicon by carbon is 1669 °C, and the complete destruction of mullite is achieved above 1500 °C. Therefore, granules obtained from aluminum slags are quite suitable for use as a batch in the production of ferrosilicon with aluminum. Keywords: Aluminum slag, granules, aluminum oxide, high-temperature firing, derivatogram.
- 30 December 2025
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 4, 2025,p. 260-272
STUDY OF PHYSICAL AND CHEMICAL PROPERTIES OF GRANULES OBTAINED FROM ALUMINUM SLAGS
This article presents the studies of the physicochemical properties of granules obtained by granulation of aluminum slags. During the studies, the granules were subjected to hardening firing at high temperatures to understand the chemistry of the process. To study the physicochemical properties, samples of granules obtained from aluminum slags were prepared, which were subjected to microanalysis by scanning electron microscopy, X-ray phase analysis and derivatographic studies. The studies showed that the main phases in the granules are Al2MgO4, Al5,65Mg2,39O10Si1,45, MgO3Si, Al2,4O4,8Si0,6, Al2O3. The main part of the studied granules is represented by spinel, mullite, aluminum oxide, sapphirine. Moreover, spinels in the phase composition of sample №. 1 amounted to 25.4 %, sapphirine 26.0 %, aluminum oxides 25 % and mullite accounts for 11.7 5, the rest is MgO3Si (11.9 %). The theoretical temperature of the reduction of the main element of silicon by carbon is 1669 °C, and the complete destruction of mullite is achieved above 1500 °C. Therefore, granules obtained from aluminum slags are quite suitable for use as a batch in the production of ferrosilicon with aluminum. Keywords: Aluminum slag, granules, aluminum oxide, high-temperature firing, derivatogram.
- Open Access
- 11 November 2025
- Published by Elsevier in Journal of Alloys and Metallurgical Systems
- Vol. 12
Study of the use of aluminium-containing waste in ferrosilicon production
- 11 November 2025
- Published by Elsevier in Journal of Alloys and Metallurgical Systems
- Vol. 12
Open AccessStudy of the use of aluminium-containing waste in ferrosilicon production
- Open Access
- 30 June 2025
- Published by Satbayev University in Engineering Journal of Satbayev University
- Vol. 147 (3) , 14-19
Features of mineral formation in the structure of iron ore materials from the position of the state diagram of the system CaO–Fe2O3–SiO2
This paper presents the results of a study of the strengthening of iron ore raw materials obtained by oxidative roasting of granules and pellets using gaseous fuel and agglomeration with combustion of solid fuel in the agglomeration layer. Differences in the mechanisms of mineral formation of granules, pellets and agglomerates appear at the stage of liquid-phase strengthening and are due to the different role of iron in forming the strengthening melt. At the same time, in the agglomerate, granules and pellets, iron is in different valence states, affecting the processes' features. Iron can be in a trivalent state in the iron-silicate melt of granules and pellets and is not a silicate-forming component of the charge. The silicate compositions of the binders in the entire studied range of basicities (0.3-1.5) are located along the line of the CaO–SiO2 connection, which is determined using the phase diagram of the CaO–Fe2O3–SiO2 system. During agglomeration, the silicon-containing melt is formed under conditions of excess FeO, which directs the process of mineral formation during the creation of the iron-silicate binder of the agglomerate. Under standard agglomeration conditions, silicate binders with a basicity of 1.0-1.5 are formed in the olivine field of the CaO–FeO–SiO2 phase diagram, covering a wide range of compositions. The processes of mineral formation in batches, by hardened methods, both during the firing of granules, pellets, and during agglomeration, have shown that changing the oxidation potential of the gas phase is an effective lever on the path not only to improving the properties of ferrous sand - a waste product of alumina production, but also to creating both new binders and new types of iron ore raw materials suitable for smelting ferrosilicon.
- 30 June 2025
- Published by Satbayev University in Engineering Journal of Satbayev University
- Vol. 147 (3) , 14-19
Open AccessFeatures of mineral formation in the structure of iron ore materials from the position of the state diagram of the system CaO–Fe2O3–SiO2
This paper presents the results of a study of the strengthening of iron ore raw materials obtained by oxidative roasting of granules and pellets using gaseous fuel and agglomeration with combustion of solid fuel in the agglomeration layer. Differences in the mechanisms of mineral formation of granules, pellets and agglomerates appear at the stage of liquid-phase strengthening and are due to the different role of iron in forming the strengthening melt. At the same time, in the agglomerate, granules and pellets, iron is in different valence states, affecting the processes' features. Iron can be in a trivalent state in the iron-silicate melt of granules and pellets and is not a silicate-forming component of the charge. The silicate compositions of the binders in the entire studied range of basicities (0.3-1.5) are located along the line of the CaO–SiO2 connection, which is determined using the phase diagram of the CaO–Fe2O3–SiO2 system. During agglomeration, the silicon-containing melt is formed under conditions of excess FeO, which directs the process of mineral formation during the creation of the iron-silicate binder of the agglomerate. Under standard agglomeration conditions, silicate binders with a basicity of 1.0-1.5 are formed in the olivine field of the CaO–FeO–SiO2 phase diagram, covering a wide range of compositions. The processes of mineral formation in batches, by hardened methods, both during the firing of granules, pellets, and during agglomeration, have shown that changing the oxidation potential of the gas phase is an effective lever on the path not only to improving the properties of ferrous sand - a waste product of alumina production, but also to creating both new binders and new types of iron ore raw materials suitable for smelting ferrosilicon.
- 30 September 2024
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 3.2024,p. 187-199
DETERMINATION OF OPTIMAL PARAMETERS OF SINTERING OF ROLLING SCALE
This article presents the results of studies conducted to determine the optimal parameters of sintering of rolled scale in a mixture with iron-containing steelmaking waste. The conducted studies of sintering of rolled scale have shown that the gas permeability of the charge depends on a number of physical properties, the size and shape of the grains, the amount of return, the height of the charge layer, and the moisture content of the charge. The initial gas permeability strongly depends on the degree of humidification of the agglomeration charge, especially when sintering small classes of materials under study. The maximum gas permeability of the charge is ensured with an optimal granulometric composition of the charge, which is characterized by an average equivalent diameter: the higher this indicator, the higher the gas permeability of the charge. The value of the surface tension reaches its maximum at a certain moisture content of the charge, which is the optimal moisture for this charge. By increasing the amount of return during agglomeration, the vertical sintering rate increases and the quality of the agglomerate improves. These factors lead to an increase in the productivity of sintering plants. According to the results of the study, the optimal parameters of the sintering sintering process of rolled scale in a mixture with iron-containing steelmaking waste were worked out. It is established that the optimal amount of return is the use of 20 % of the mass of the sintering charge at the optimal height of the sintered layer of 300 mm. As a result of the conducted research, the following optimal indicators were achieved: mechanical strength – 70.2 %, sintering rate – 28.7 mm/min, specific productivity – 1.75 t/m2·hour. Keywords: Rolling scale, agglomeration, optimal parameters, sintering, return, layer height.
- 30 September 2024
- Published by Toraighyrov University in Science and Technology of Kazakhstan
- No. 3.2024,p. 187-199
DETERMINATION OF OPTIMAL PARAMETERS OF SINTERING OF ROLLING SCALE
This article presents the results of studies conducted to determine the optimal parameters of sintering of rolled scale in a mixture with iron-containing steelmaking waste. The conducted studies of sintering of rolled scale have shown that the gas permeability of the charge depends on a number of physical properties, the size and shape of the grains, the amount of return, the height of the charge layer, and the moisture content of the charge. The initial gas permeability strongly depends on the degree of humidification of the agglomeration charge, especially when sintering small classes of materials under study. The maximum gas permeability of the charge is ensured with an optimal granulometric composition of the charge, which is characterized by an average equivalent diameter: the higher this indicator, the higher the gas permeability of the charge. The value of the surface tension reaches its maximum at a certain moisture content of the charge, which is the optimal moisture for this charge. By increasing the amount of return during agglomeration, the vertical sintering rate increases and the quality of the agglomerate improves. These factors lead to an increase in the productivity of sintering plants. According to the results of the study, the optimal parameters of the sintering sintering process of rolled scale in a mixture with iron-containing steelmaking waste were worked out. It is established that the optimal amount of return is the use of 20 % of the mass of the sintering charge at the optimal height of the sintered layer of 300 mm. As a result of the conducted research, the following optimal indicators were achieved: mechanical strength – 70.2 %, sintering rate – 28.7 mm/min, specific productivity – 1.75 t/m2·hour. Keywords: Rolling scale, agglomeration, optimal parameters, sintering, return, layer height.
- 1 January 2016
- Published by Akademizdatcenter Nauka in Кинетика и катализ
- Vol. 57 (4) , 484-492
Каталитическая активация слоистых силикатов для синтеза нанокомпозиционных материалов на основе сверхвысокомолекулярного полиэтилена
Бревнов П.Н., Заболотнов А.С., Крашенинников В.Г., Покидько Б.В., Бакиров А.В., Бабкина О.Н., Новокшонова Л.А.//Кинетика и катализ, 2016
- 1 January 2016
- Published by Akademizdatcenter Nauka in Кинетика и катализ
- Vol. 57 (4) , 484-492
Каталитическая активация слоистых силикатов для синтеза нанокомпозиционных материалов на основе сверхвысокомолекулярного полиэтилена
Бревнов П.Н., Заболотнов А.С., Крашенинников В.Г., Покидько Б.В., Бакиров А.В., Бабкина О.Н., Новокшонова Л.А.//Кинетика и катализ, 2016