Berkay Menç
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Berkay Menç has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Gizem Candaş
ROKETSAN, Missiles Industries Inc. Ankara Elmadağ Türkiye
3 shared publications - Yusuf Özçatalbaş
Gazi Üniversitesi, Teknoloji Fakültesi
3 shared publications Yusuf Özçatalbaş
Gazi University
1 shared publication
Latest Publications
- 24 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (16) , 14665-14677
A Comparative Study on the Bond Strength and Failure Mechanisms of CFRP / AA7075 ‐ T6 Joints: Effects of Sandblasting and Anodizing Process
This study investigates the bonding performance of carbon fiber reinforced polymer (CFRP) and AA7075‐T6 aluminum alloy hybrid structures, which are critical for aerospace and defense applications. The research evaluates the impact of various metal surface treatments on adhesion using a Syensqo MTA 240 epoxy‐based adhesive film. Five distinct surface configurations were applied to the AA7075‐T6 plates: HNO 3 etching, NC machined cross‐hatching, silica grit blasting, and clear anodizing following glass bead blasting. These treatments yielded surface roughness values ranging from Ra 0.23 to 4.10 μm. Single‐lap shear tests were conducted according to ASTM D1002, and failure mechanisms were characterized using optical microscopy, SEM, and X‐Ray Fluorescence (XRF) analyses. The results revealed that anodized and silica‐sandblasted specimens achieved 98% and 82% higher lap shear strength than the untreated reference specimen, respectively. Conversely, cross‐hatched specimens exhibited the lowest performance at 7.30 MPa. Metallographic investigations and SEM‐XRF analyses demonstrated that both the cross‐hatch patterns and the as‐received surfaces had a detrimental effect on the bonding performance. In contrast, it was determined that sandblasting and anodizing treatments facilitated the joining of AA7075‐T6 and CFRP plates, resulting in a stronger interfacial bond.
- 24 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (16) , 14665-14677
A Comparative Study on the Bond Strength and Failure Mechanisms of CFRP / AA7075 ‐ T6 Joints: Effects of Sandblasting and Anodizing Process
This study investigates the bonding performance of carbon fiber reinforced polymer (CFRP) and AA7075‐T6 aluminum alloy hybrid structures, which are critical for aerospace and defense applications. The research evaluates the impact of various metal surface treatments on adhesion using a Syensqo MTA 240 epoxy‐based adhesive film. Five distinct surface configurations were applied to the AA7075‐T6 plates: HNO 3 etching, NC machined cross‐hatching, silica grit blasting, and clear anodizing following glass bead blasting. These treatments yielded surface roughness values ranging from Ra 0.23 to 4.10 μm. Single‐lap shear tests were conducted according to ASTM D1002, and failure mechanisms were characterized using optical microscopy, SEM, and X‐Ray Fluorescence (XRF) analyses. The results revealed that anodized and silica‐sandblasted specimens achieved 98% and 82% higher lap shear strength than the untreated reference specimen, respectively. Conversely, cross‐hatched specimens exhibited the lowest performance at 7.30 MPa. Metallographic investigations and SEM‐XRF analyses demonstrated that both the cross‐hatch patterns and the as‐received surfaces had a detrimental effect on the bonding performance. In contrast, it was determined that sandblasting and anodizing treatments facilitated the joining of AA7075‐T6 and CFRP plates, resulting in a stronger interfacial bond.
- 16 April 2026
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- p. 1-20
Investigation of the effect of surface treatments on the shear performance of CFRP/Ti–6Al–4V single-lap adhesive joints
1. The aerospace and automotive industries have increasingly adopted lightweight and high-strength materials (Al, Mg, Ti alloys, and polymer composites) instead of traditional heavy metals to impro...
- 16 April 2026
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- p. 1-20
Investigation of the effect of surface treatments on the shear performance of CFRP/Ti–6Al–4V single-lap adhesive joints
1. The aerospace and automotive industries have increasingly adopted lightweight and high-strength materials (Al, Mg, Ti alloys, and polymer composites) instead of traditional heavy metals to impro...
- Open Access
- 17 March 2026
- Published by Elsevier in SSRN Electronic Journal
A Comparative Study on the Bond Strength and Failure Mechanisms of CFRP / AA7075-T6 Joints: Effects of Sandblasting and Anodizing Process
This study aims to investigate the bonding performance of CFRP + AA7075-T6 aluminum alloy hybrid structures, which are of critical importance in engineering applications in the aerospace and defense fields. The effects of various metal surface preparation treatments on adhesion performance were experimentally investigated using an epoxy-based adhesive film. Twill-weave CFRP laminates and AA7075-T6 aluminum alloy plates were bonded using Syensqo MTA 240/PK13-313g/m2 adhesive to fabricate single-lap shear test specimens. Five distinct surface configurations were applied to the AA7075-T6 plates. These treatments included HNO3 etching, NC machined cross-hatching, silica grit blasting, and clear anodizing subsequent to glass bead blasting. Following these treatments, surface roughness values ranging from Ra 0.23 to 4.10 µm (Rz 1.56 – 24.21 µm) were obtained for the Al alloy specimens. Failure mechanisms were characterized using optical microscopy and SEM-IXRF analyses. Following single-lap shear tests performed according to ASTM D1002, the highest average lap shear strengths were obtained for the anodized and silica sandblasted aluminum specimens, with values of 15.77 MPa and 14.50 MPa, respectively. The lowest strength was recorded for the cross-hatched specimens, with an average value of 7.30 MPa. Metallographic investigations and SEM-IXRF analyses demonstrated that both the cross-hatch patterns and the as-received surfaces had a detrimental effect on the bonding performance. In contrast, it was determined that sandblasting and anodizing treatments facilitated the joining of AA7075-T6 and CFRP plates, resulting in a stronger interfacial bond.
- 17 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Comparative Study on the Bond Strength and Failure Mechanisms of CFRP / AA7075-T6 Joints: Effects of Sandblasting and Anodizing Process
This study aims to investigate the bonding performance of CFRP + AA7075-T6 aluminum alloy hybrid structures, which are of critical importance in engineering applications in the aerospace and defense fields. The effects of various metal surface preparation treatments on adhesion performance were experimentally investigated using an epoxy-based adhesive film. Twill-weave CFRP laminates and AA7075-T6 aluminum alloy plates were bonded using Syensqo MTA 240/PK13-313g/m2 adhesive to fabricate single-lap shear test specimens. Five distinct surface configurations were applied to the AA7075-T6 plates. These treatments included HNO3 etching, NC machined cross-hatching, silica grit blasting, and clear anodizing subsequent to glass bead blasting. Following these treatments, surface roughness values ranging from Ra 0.23 to 4.10 µm (Rz 1.56 – 24.21 µm) were obtained for the Al alloy specimens. Failure mechanisms were characterized using optical microscopy and SEM-IXRF analyses. Following single-lap shear tests performed according to ASTM D1002, the highest average lap shear strengths were obtained for the anodized and silica sandblasted aluminum specimens, with values of 15.77 MPa and 14.50 MPa, respectively. The lowest strength was recorded for the cross-hatched specimens, with an average value of 7.30 MPa. Metallographic investigations and SEM-IXRF analyses demonstrated that both the cross-hatch patterns and the as-received surfaces had a detrimental effect on the bonding performance. In contrast, it was determined that sandblasting and anodizing treatments facilitated the joining of AA7075-T6 and CFRP plates, resulting in a stronger interfacial bond.
- 17 October 2024
- Published by SAGE Publications in Materials Science and Technology
- Vol. 42 (1) , 93-105
Manufacturing and characterization of open-cell aluminum foam by powder metallurgy
Metallic foams are classified into two groups based on their pore structure: closed and open pores. The variability of cell structures directly depends on the production method and the variability of parameters. Open – cell metallic foams are used as heat exchangers due to their large surface area, in filters and separators due to their properties such as high liquid/gas permeability and corrosion resistance, and in water purifiers to reduce the concentration of unwanted ions dissolved in water because they can provide liquid flow, and in silencers due to their sound absorbing feature. Due to their thermal conductivity, they are generally used in functional applications such as catalyst supports and flame arresters. In this study, open cell aluminum foams with different pore sizes were produced using the powder metallurgy method and polyurethane foam (PUF) replica technique. After the PUF model material of the foams was removed at 500 °C for 6 h, they were sintered at different temperatures such as 850, 900 and 950 °C for 6 h. Density measurement, XRD analysis, microstructure examination and compression testing were applied to the sintered open-cell foams. The highest pore ratio and compressive strength were determined in foams with a 20 ppi (porosity per inch) pore ratio sintered at 950 °C.
- 17 October 2024
- Published by SAGE Publications in Materials Science and Technology
- Vol. 42 (1) , 93-105
Manufacturing and characterization of open-cell aluminum foam by powder metallurgy
Metallic foams are classified into two groups based on their pore structure: closed and open pores. The variability of cell structures directly depends on the production method and the variability of parameters. Open – cell metallic foams are used as heat exchangers due to their large surface area, in filters and separators due to their properties such as high liquid/gas permeability and corrosion resistance, and in water purifiers to reduce the concentration of unwanted ions dissolved in water because they can provide liquid flow, and in silencers due to their sound absorbing feature. Due to their thermal conductivity, they are generally used in functional applications such as catalyst supports and flame arresters. In this study, open cell aluminum foams with different pore sizes were produced using the powder metallurgy method and polyurethane foam (PUF) replica technique. After the PUF model material of the foams was removed at 500 °C for 6 h, they were sintered at different temperatures such as 850, 900 and 950 °C for 6 h. Density measurement, XRD analysis, microstructure examination and compression testing were applied to the sintered open-cell foams. The highest pore ratio and compressive strength were determined in foams with a 20 ppi (porosity per inch) pore ratio sintered at 950 °C.