Ilyos J. Abdisaidov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ilyos J. Abdisaidov has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ilyos Kh. Khudaykulov
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
4 shared publications - Khatam B. Ashurov
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
4 shared publications Sevara G. Gulomjanova
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
2 shared publicationsSardor A. Tulaganov
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
1 shared publication- Sevarakhon G. Gulomjanova
Arifov Institute of Ion-Plasma and Laser Technologies of Uzbekistan Academy of Sciences, Tashkent, Uzbekistan
1 shared publication - Usmonjon F. Berdiyev
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
1 shared publication
Latest Publications
- Open Access
- 10 June 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 2,p. 156-161
The Systematic Correlation Between Synthesis Parameters and the Particle Size of Nickel Oxide Nanocatalysts Prepared by the Sol–Gel Method
In this work, the sol-gel synthesis of nickel oxide (NiO) nanoparticles was systematically examined with respect to key parameters, including precursor type, reagent molar ratio, reaction time, and calcination temperature. A comparative evaluation of different nickel-based salts identified nickel nitrate as the most suitable precursor. Structural–phase characterization by X-ray diffraction (XRD) demonstrated that the nanoparticles synthesized at varying reagent ratios possessed well-defined crystalline phases, with an average crystallite size of ~11 nm. Prolonged reaction times were observed to promote agglomeration processes. Raman spectroscopic analysis revealed the presence of phonon and magnon vibrational modes, which were strongly dependent on particle size and calcination conditions. Transmission electron microscopy (TEM) confirmed a particle size distribution in the range of 3÷19 nm. Collectively, these results establish the synthesis–structure relationship and provide a framework for defining optimal conditions for preparing NiO nanocatalysts.
- 10 June 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 2,p. 156-161
Open AccessThe Systematic Correlation Between Synthesis Parameters and the Particle Size of Nickel Oxide Nanocatalysts Prepared by the Sol–Gel Method
In this work, the sol-gel synthesis of nickel oxide (NiO) nanoparticles was systematically examined with respect to key parameters, including precursor type, reagent molar ratio, reaction time, and calcination temperature. A comparative evaluation of different nickel-based salts identified nickel nitrate as the most suitable precursor. Structural–phase characterization by X-ray diffraction (XRD) demonstrated that the nanoparticles synthesized at varying reagent ratios possessed well-defined crystalline phases, with an average crystallite size of ~11 nm. Prolonged reaction times were observed to promote agglomeration processes. Raman spectroscopic analysis revealed the presence of phonon and magnon vibrational modes, which were strongly dependent on particle size and calcination conditions. Transmission electron microscopy (TEM) confirmed a particle size distribution in the range of 3÷19 nm. Collectively, these results establish the synthesis–structure relationship and provide a framework for defining optimal conditions for preparing NiO nanocatalysts.
- Open Access
- 14 March 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 357-362
The Improving Carbon Nanotube Synthesis by the Removal of Amorphous Carbon
In this study, carbon nanotubes (CNTs) were synthesized on Ni-coated sapphire substrates using conventional and water-assisted chemical vapor deposition (CVD and WA-CVD) methods to evaluate the effect of water vapor on amorphous carbon removal and catalyst activity at low temperatures. Reduced nickel nanocatalysts were prepared by the sol–gel method and activated in a hydrogen atmosphere. Raman spectroscopy confirmed that CNTs synthesized by WA-CVD exhibited a higher degree of graphitization (ID/IG ≈ 1.18) and the absence of amorphous carbon peaks around 794 cm⁻¹, indicating improved purity. X-ray diffraction (XRD) analysis revealed the formation of graphitic carbon (002) and Ni₃C crystalline phases, as well as a rightward shift of the (002) peak to 2θ = 26.2°, suggesting lattice contraction caused by water-vapor-induced stress. Transmission electron microscopy (TEM) images showed that CNTs synthesized under WA-CVD conditions were thinner (17–25 nm), longer (≥ 1 µm), and cleaner than those obtained by conventional CVD, which exhibited thick amorphous carbon coatings. These results demonstrate that the controlled addition of water vapor during CVD suppresses amorphous carbon formation, regenerates catalyst active sites, and significantly enhances CNT crystallinity and morphological uniformity. The findings provide an efficient approach for synthesizing high-purity, well-aligned CNTs suitable for thermal interface materials, nanocomposites, and electronic device applications.
- 14 March 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 357-362
Open AccessThe Improving Carbon Nanotube Synthesis by the Removal of Amorphous Carbon
In this study, carbon nanotubes (CNTs) were synthesized on Ni-coated sapphire substrates using conventional and water-assisted chemical vapor deposition (CVD and WA-CVD) methods to evaluate the effect of water vapor on amorphous carbon removal and catalyst activity at low temperatures. Reduced nickel nanocatalysts were prepared by the sol–gel method and activated in a hydrogen atmosphere. Raman spectroscopy confirmed that CNTs synthesized by WA-CVD exhibited a higher degree of graphitization (ID/IG ≈ 1.18) and the absence of amorphous carbon peaks around 794 cm⁻¹, indicating improved purity. X-ray diffraction (XRD) analysis revealed the formation of graphitic carbon (002) and Ni₃C crystalline phases, as well as a rightward shift of the (002) peak to 2θ = 26.2°, suggesting lattice contraction caused by water-vapor-induced stress. Transmission electron microscopy (TEM) images showed that CNTs synthesized under WA-CVD conditions were thinner (17–25 nm), longer (≥ 1 µm), and cleaner than those obtained by conventional CVD, which exhibited thick amorphous carbon coatings. These results demonstrate that the controlled addition of water vapor during CVD suppresses amorphous carbon formation, regenerates catalyst active sites, and significantly enhances CNT crystallinity and morphological uniformity. The findings provide an efficient approach for synthesizing high-purity, well-aligned CNTs suitable for thermal interface materials, nanocomposites, and electronic device applications.
- Open Access
- 14 March 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 256-260
The Enhancing the Yield of Carbon Nanotubes Through the Nanocatalyst-Substrate Interface
In this study, the effect of the nanocatalyst/substrate interface on the yield and quality of carbon nanotubes (CNTs) synthesized by chemical vapor deposition (CVD) was investigated. Nickel oxide (NiO) nanoparticles were prepared using the sol–gel spin-coating method and deposited as thin films with different masses (66 mg, 99 mg, and 132 mg) on SiO2/Si substrates with an identical surface area of 12,56 cm2. The NiO nanoparticle thin films on the substrate surface were then placed into a CVD reactor and reduced in a hydrogen atmosphere, resulting in the formation of nickel nanoparticles that acted as active catalysts during CNTs synthesis. Ethanol vapor was used as the sole carbon source without any carrier gas, which enabled precise and comparative evaluation of the CNTs yield. X-ray diffraction (XRD) and Raman spectroscopy were employed to characterize the obtained CNTs. XRD results showed that CNTs with high crystallinity were produced when a 51,7 mg catalyst thin film was used. Raman spectroscopy confirmed the presence of RBM, G, D, and G′ peaks characteristic of CNTs structures. Increasing the catalyst mass led to a rise in RBM frequency and a decrease in CNTs diameter. However, an increase in catalyst mass also caused a reduction in CNTs yield. The highest yield (445%) was observed for Ni nanocatalysts with a mass of 51,7 mg. These findings demonstrate that the thickness of the catalyst layer and its surface distribution density on the substrate play a crucial role in determining the growth efficiency and structural quality of CNTs.
- 14 March 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 256-260
Open AccessThe Enhancing the Yield of Carbon Nanotubes Through the Nanocatalyst-Substrate Interface
In this study, the effect of the nanocatalyst/substrate interface on the yield and quality of carbon nanotubes (CNTs) synthesized by chemical vapor deposition (CVD) was investigated. Nickel oxide (NiO) nanoparticles were prepared using the sol–gel spin-coating method and deposited as thin films with different masses (66 mg, 99 mg, and 132 mg) on SiO2/Si substrates with an identical surface area of 12,56 cm2. The NiO nanoparticle thin films on the substrate surface were then placed into a CVD reactor and reduced in a hydrogen atmosphere, resulting in the formation of nickel nanoparticles that acted as active catalysts during CNTs synthesis. Ethanol vapor was used as the sole carbon source without any carrier gas, which enabled precise and comparative evaluation of the CNTs yield. X-ray diffraction (XRD) and Raman spectroscopy were employed to characterize the obtained CNTs. XRD results showed that CNTs with high crystallinity were produced when a 51,7 mg catalyst thin film was used. Raman spectroscopy confirmed the presence of RBM, G, D, and G′ peaks characteristic of CNTs structures. Increasing the catalyst mass led to a rise in RBM frequency and a decrease in CNTs diameter. However, an increase in catalyst mass also caused a reduction in CNTs yield. The highest yield (445%) was observed for Ni nanocatalysts with a mass of 51,7 mg. These findings demonstrate that the thickness of the catalyst layer and its surface distribution density on the substrate play a crucial role in determining the growth efficiency and structural quality of CNTs.
- Open Access
- 2 September 2024
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 3,p. 355-358
The Low-Temperature Growth of Carbon Nanotubes Using Nickel Catalyst
This study presents the results of a comprehensive investigation into the fabrication of single-walled carbon nanotubes (SWCNTs) employing chemical vapor deposition (CVD) technique, with nickel nanoparticles serving as crucial catalysts. These nanoparticles are synthesized via the reduction of oxide precursors using hydrogen and are strategically incorporated with ethanol vapor as the primary carbon source. The effectiveness and reproducibility of this synthesis method are thoroughly validated using advanced analytical techniques. Particularly noteworthy is the demonstrated ability to conduct the process at relatively low temperatures, not exceeding 500°C, which is of significant importance. Such precise control over synthesis conditions not only augurs well for the scalability of SWCNT production but also carries substantial implications for the advancement of nanomaterial synthesis methodologies.
- 2 September 2024
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 3,p. 355-358
Open AccessThe Low-Temperature Growth of Carbon Nanotubes Using Nickel Catalyst
This study presents the results of a comprehensive investigation into the fabrication of single-walled carbon nanotubes (SWCNTs) employing chemical vapor deposition (CVD) technique, with nickel nanoparticles serving as crucial catalysts. These nanoparticles are synthesized via the reduction of oxide precursors using hydrogen and are strategically incorporated with ethanol vapor as the primary carbon source. The effectiveness and reproducibility of this synthesis method are thoroughly validated using advanced analytical techniques. Particularly noteworthy is the demonstrated ability to conduct the process at relatively low temperatures, not exceeding 500°C, which is of significant importance. Such precise control over synthesis conditions not only augurs well for the scalability of SWCNT production but also carries substantial implications for the advancement of nanomaterial synthesis methodologies.