József Beke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
József Beke has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Szabolcs Szalai
Department of Vehicle Production and Engineering, Széchenyi István University, Egyetem tér 1, 9026 Győr, Hungary
2 shared publications - Attila Nagy
Department of Applied Mechanics, Széchenyi István University, Egyetem tér 1, 9026 Győr, Hungary
1 shared publication - László Pálfi
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
1 shared publication
Latest Publications
- Open Access
- 3 November 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 45
Effect of Printing Orientation on the Mechanical and Geometrical Properties of FDM-Printed Specimens Manufactured from PLA
In fused deposition modelling (FDM), build orientation is known to govern the mechanical properties of printed parts, but its effect on geometric and form accuracy is far less thoroughly characterised. This study investigates how build orientation influences the dimensional and form characteristics of FDM-printed PLA specimens, evaluated together with their tensile behaviour on the same parts. Rectangular tensile specimens were printed from PLA at a fixed infill in four representative build orientations—flat, on-edge, 45°, and upright. Dimensional accuracy was measured by coordinate measuring machine (CMM) inspection and the flatness of the principal faces by optical 3D scanning, and the same specimens were then tensile tested. The results show that geometric accuracy and strength vary together with build orientation: the 45° orientation produced the largest flatness error together with the lowest tensile strength, whereas the on-edge orientation combined the best flatness with the highest strength. Because build orientation was the only variable, this co-variation reflects their shared dependence on orientation rather than a direct causal link between flatness and strength. Comparing the form deviations across orientations therefore shows that the geometrically and mechanically preferable build directions can coincide, providing practical guidance for selecting build orientation when both matter.
- 3 November 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 45
Open AccessEffect of Printing Orientation on the Mechanical and Geometrical Properties of FDM-Printed Specimens Manufactured from PLA
In fused deposition modelling (FDM), build orientation is known to govern the mechanical properties of printed parts, but its effect on geometric and form accuracy is far less thoroughly characterised. This study investigates how build orientation influences the dimensional and form characteristics of FDM-printed PLA specimens, evaluated together with their tensile behaviour on the same parts. Rectangular tensile specimens were printed from PLA at a fixed infill in four representative build orientations—flat, on-edge, 45°, and upright. Dimensional accuracy was measured by coordinate measuring machine (CMM) inspection and the flatness of the principal faces by optical 3D scanning, and the same specimens were then tensile tested. The results show that geometric accuracy and strength vary together with build orientation: the 45° orientation produced the largest flatness error together with the lowest tensile strength, whereas the on-edge orientation combined the best flatness with the highest strength. Because build orientation was the only variable, this co-variation reflects their shared dependence on orientation rather than a direct causal link between flatness and strength. Comparing the form deviations across orientations therefore shows that the geometrically and mechanically preferable build directions can coincide, providing practical guidance for selecting build orientation when both matter.
- Open Access
- 15 November 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 79 (1) , 90
A Pre-Study of the Relationship Between Machining Technology Parameters and Surface Roughness in the Scope of the Optimal Cost Efficiency of Machining
This research investigates the relationship between machining technology parameters and surface roughness to optimize the cost efficiency of machining processes. In modern manufacturing, particularly in the automotive sector, achieving the desired surface quality while minimizing costs is critical. By evaluating tools from various manufacturers under different combinations of cutting parameters—such as cutting speed, feed, and depth—this study focuses on determining the most effective settings for producing an optimal surface roughness. The experiments highlight that selecting appropriate technological parameters impacts the machining process’s surface finish and economic efficiency. This study provides insights into balancing surface quality requirements with cost constraints, contributing to more efficient and sustainable manufacturing practices.
- 15 November 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 79 (1) , 90
Open AccessA Pre-Study of the Relationship Between Machining Technology Parameters and Surface Roughness in the Scope of the Optimal Cost Efficiency of Machining
This research investigates the relationship between machining technology parameters and surface roughness to optimize the cost efficiency of machining processes. In modern manufacturing, particularly in the automotive sector, achieving the desired surface quality while minimizing costs is critical. By evaluating tools from various manufacturers under different combinations of cutting parameters—such as cutting speed, feed, and depth—this study focuses on determining the most effective settings for producing an optimal surface roughness. The experiments highlight that selecting appropriate technological parameters impacts the machining process’s surface finish and economic efficiency. This study provides insights into balancing surface quality requirements with cost constraints, contributing to more efficient and sustainable manufacturing practices.