Attila Nagy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Attila Nagy has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Szabolcs Szalai
Department of Vehicle Production and Engineering, Széchenyi István University, Egyetem tér 1, 9026 Győr, Hungary
2 shared publications - András Lajos Nagy
Department of Propulsion Technology, Széchenyi István University, Egyetem tér 1, H-9026 Győr, Hungary
1 shared publication - Gusztáv Baranyai
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
1 shared publication - Hanna Csótár
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
1 shared publication - József Beke
Department of Vehicle Production and Engineering, Széchenyi István University, Egyetem tér 1, 9026 Győr, Hungary
1 shared publication - Szabolcs Fischer
Central Campus Győr, Széchenyi István University, H-9026 Győr, Hungary
1 shared publication
Latest Publications
- Open Access
- 3 November 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 45
Effect of Printing Orientation on the Mechanical and Geometrical Properties of FDM-Printed Specimens Manufactured from PLA
In fused deposition modelling (FDM), build orientation is known to govern the mechanical properties of printed parts, but its effect on geometric and form accuracy is far less thoroughly characterised. This study investigates how build orientation influences the dimensional and form characteristics of FDM-printed PLA specimens, evaluated together with their tensile behaviour on the same parts. Rectangular tensile specimens were printed from PLA at a fixed infill in four representative build orientations—flat, on-edge, 45°, and upright. Dimensional accuracy was measured by coordinate measuring machine (CMM) inspection and the flatness of the principal faces by optical 3D scanning, and the same specimens were then tensile tested. The results show that geometric accuracy and strength vary together with build orientation: the 45° orientation produced the largest flatness error together with the lowest tensile strength, whereas the on-edge orientation combined the best flatness with the highest strength. Because build orientation was the only variable, this co-variation reflects their shared dependence on orientation rather than a direct causal link between flatness and strength. Comparing the form deviations across orientations therefore shows that the geometrically and mechanically preferable build directions can coincide, providing practical guidance for selecting build orientation when both matter.
- 3 November 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 45
Open AccessEffect of Printing Orientation on the Mechanical and Geometrical Properties of FDM-Printed Specimens Manufactured from PLA
In fused deposition modelling (FDM), build orientation is known to govern the mechanical properties of printed parts, but its effect on geometric and form accuracy is far less thoroughly characterised. This study investigates how build orientation influences the dimensional and form characteristics of FDM-printed PLA specimens, evaluated together with their tensile behaviour on the same parts. Rectangular tensile specimens were printed from PLA at a fixed infill in four representative build orientations—flat, on-edge, 45°, and upright. Dimensional accuracy was measured by coordinate measuring machine (CMM) inspection and the flatness of the principal faces by optical 3D scanning, and the same specimens were then tensile tested. The results show that geometric accuracy and strength vary together with build orientation: the 45° orientation produced the largest flatness error together with the lowest tensile strength, whereas the on-edge orientation combined the best flatness with the highest strength. Because build orientation was the only variable, this co-variation reflects their shared dependence on orientation rather than a direct causal link between flatness and strength. Comparing the form deviations across orientations therefore shows that the geometrically and mechanically preferable build directions can coincide, providing practical guidance for selecting build orientation when both matter.
- Open Access
- 10 November 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 113 (1) , 45
Structural Integrity Analysis of 3D-Printed PLA- and ABS-Reinforced Concrete Underwater Curing
The optimization and evaluation of 3D-printed polylactic acid (PLA) and ABS materials present a promising approach for enhancing the reinforcement of concrete elements, thereby advancing sustainable construction technologies. This study examines the degradation of the structural integrity of 3D-printed PLA- and ABS-reinforced concrete after 28 days of underwater curing. The research focuses on macroscopic analysis and microscopic characterization using a digital microscope and a high-resolution camera to investigate the crystalline structures formed during curing. The findings will offer valuable insights into the structural transformations occurring within concrete elements and potential interactions between concrete and PLA structures, paving the way for future civil engineering applications.
- 10 November 2025
- Published by MDPI AG in Engineering Proceedings
- Vol. 113 (1) , 45
Open AccessStructural Integrity Analysis of 3D-Printed PLA- and ABS-Reinforced Concrete Underwater Curing
The optimization and evaluation of 3D-printed polylactic acid (PLA) and ABS materials present a promising approach for enhancing the reinforcement of concrete elements, thereby advancing sustainable construction technologies. This study examines the degradation of the structural integrity of 3D-printed PLA- and ABS-reinforced concrete after 28 days of underwater curing. The research focuses on macroscopic analysis and microscopic characterization using a digital microscope and a high-resolution camera to investigate the crystalline structures formed during curing. The findings will offer valuable insights into the structural transformations occurring within concrete elements and potential interactions between concrete and PLA structures, paving the way for future civil engineering applications.