Didin Sahidin Winatapura
Research Subjects
Didin Sahidin Winatapura has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Ade Mulyawan
Natl Res & Innovat Agcy, Res Ctr Adv Mat, Tangerang 15314, Indonesia
3 shared publications - Wisnu Ari Adi
Research Center for Energy Materials, National Research and Innovation Agency, Kawasan Sains Teknologi Habibie, Serpong, Indonesia
3 shared publications - Mashadi Mashadi
National Research and Innovation Agency (BRIN)
2 shared publications - Yana Taryana
Research Center for Telecommunication, National Research and Innovation Agency, Bandung, Indonesia
2 shared publications - Yunasfi Yunasfi
Research Center for Energy Materials, National Research and Innovation Agency, Kawasan Sains Teknologi Habibie, Serpong, Indonesia
2 shared publications - Agus Susanto
Earth Physics Laboratory, Department of Physics, Faculty of Mathematics and Natural Science, Universitas Negeri Makassar, Kampus UNM Parangtambung Jl. Daeng Tata Raya Makassar 90224, Indonesia
1 shared publication
Latest Publications
- Open Access
- 1 December 2025
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 25 (6) , 1768
Sustainable Synthesis and Structural Characterization of Carbon, Graphite, Graphene Oxide, and Reduced Graphene Oxide Derived from Coconut Shells
This study explores the sustainable synthesis and structural characterization of carbon, graphite, graphene oxide (GO), and reduced graphene oxide (rGO) derived from coconut shells. The objective is to investigate the potential of biomass-based precursors to produce functional carbon materials through controlled chemical treatments. X-ray diffraction patterns of carbon and graphite exhibit broad peaks, indicating low crystallinity and amorphous characteristics, while GO and rGO show dominant peaks at 22° and 23°, corresponding to the (002) plane. Scanning electron microscopy confirms the disordered morphology of carbon and graphite, while high-resolution transmission electron microscopy reveals wrinkled GO sheets and partially restacked rGO layers. Fourier transform infrared spectra identify O−H stretching at ~3442 cm−1 in carbon and C=C stretching at 1630 cm−1 in graphite, along with various oxygen-containing functional groups in GO and rGO. Raman spectroscopy shows a sharp G band at 1580 cm−1 in graphite (ID/IG = 0.840), increased disorder in GO (ID/IG = 0.843), and partial graphitic restoration in rGO (ID/IG = 0.841). These findings confirm the successful transformation of coconut shells into valuable carbon-based materials and highlight their potential for use in sustainable energy and electronic applications.
- 1 December 2025
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 25 (6) , 1768
Open AccessSustainable Synthesis and Structural Characterization of Carbon, Graphite, Graphene Oxide, and Reduced Graphene Oxide Derived from Coconut Shells
This study explores the sustainable synthesis and structural characterization of carbon, graphite, graphene oxide (GO), and reduced graphene oxide (rGO) derived from coconut shells. The objective is to investigate the potential of biomass-based precursors to produce functional carbon materials through controlled chemical treatments. X-ray diffraction patterns of carbon and graphite exhibit broad peaks, indicating low crystallinity and amorphous characteristics, while GO and rGO show dominant peaks at 22° and 23°, corresponding to the (002) plane. Scanning electron microscopy confirms the disordered morphology of carbon and graphite, while high-resolution transmission electron microscopy reveals wrinkled GO sheets and partially restacked rGO layers. Fourier transform infrared spectra identify O−H stretching at ~3442 cm−1 in carbon and C=C stretching at 1630 cm−1 in graphite, along with various oxygen-containing functional groups in GO and rGO. Raman spectroscopy shows a sharp G band at 1580 cm−1 in graphite (ID/IG = 0.840), increased disorder in GO (ID/IG = 0.843), and partial graphitic restoration in rGO (ID/IG = 0.841). These findings confirm the successful transformation of coconut shells into valuable carbon-based materials and highlight their potential for use in sustainable energy and electronic applications.
- 18 November 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (12) , 125958
Effect of anisotropy field on the resonance frequency and reflection loss shift characteristics of barium hexaferrite ceramics
For this study, a modified barium hexaferrite based microwave and radar absorbing material was used. Synthesis and characterization of BaFe(12−2x)(MnTi) x O19 (0.1 ≤ x ≤ 1.0) have been prepared by solid state reaction method. The x-ray diffraction patterns reveal that all samples only crystallized into M-type barium hexaferrite after calcination at 1200 °C. Surface morphology images show that the hexagonal flake-like particle is formed at the initial stages of the Mn-Ti substitution level. The magnetic properties measurement reveals that the variation of magnetization values may vary based on preferable site occupation of Mn4+-Ti2+ cations to replace Fe3+ cations. The significant decrease in coercive field (H c) from 3.18 kOe to 0.51 kOe with the increase of Mn-Ti substitution affected the lowering values of anisotropy field (H a ). The maximum reflection loss (RL) positions of BaFe(12−2x)(MnTi) x O19 compositional series are shifted to lower frequency range following the H a trendlines. The maximum RL value equals to 98.42% microwave absorption at 10.5 GHz has been obtained in x = 1.0 (BaFe10Mn0.5Ti0.5O19) composition.
- 18 November 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (12) , 125958
Effect of anisotropy field on the resonance frequency and reflection loss shift characteristics of barium hexaferrite ceramics
For this study, a modified barium hexaferrite based microwave and radar absorbing material was used. Synthesis and characterization of BaFe(12−2x)(MnTi) x O19 (0.1 ≤ x ≤ 1.0) have been prepared by solid state reaction method. The x-ray diffraction patterns reveal that all samples only crystallized into M-type barium hexaferrite after calcination at 1200 °C. Surface morphology images show that the hexagonal flake-like particle is formed at the initial stages of the Mn-Ti substitution level. The magnetic properties measurement reveals that the variation of magnetization values may vary based on preferable site occupation of Mn4+-Ti2+ cations to replace Fe3+ cations. The significant decrease in coercive field (H c) from 3.18 kOe to 0.51 kOe with the increase of Mn-Ti substitution affected the lowering values of anisotropy field (H a ). The maximum reflection loss (RL) positions of BaFe(12−2x)(MnTi) x O19 compositional series are shifted to lower frequency range following the H a trendlines. The maximum RL value equals to 98.42% microwave absorption at 10.5 GHz has been obtained in x = 1.0 (BaFe10Mn0.5Ti0.5O19) composition.
- 1 July 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 855, 52-57
Synthesis, Structure, Magnetic and Absorption Properties of Nd Doped Y3Fe5O12 Garnets Prepared by Mechanochemical Method
Neodymium substituted yttrium iron garnet (YIG) nanoparticles with compositional variation of NdxY3−xFe5O12 where x = 0.0, 0.2, 0.5 and 0.8 was prepared by mechanochemicals method using high energy milling (HEM). The characterization was done using X-rays diffractometer (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and vector network analyzer (VNA). It was found that the mechanical milling followed by sintering promotes the complete structural formation of the yttrium iron garnet (YIG) structure. The XRD patterns confirm the complete introduction of Nd3+ ion into the YIG with an addition of Nd doping concentration. nanocrystalline particles with high purity and sizes ranging from 0.12μm to 0.16μm were obtained. The magnetization value, Ms from all Nd-doped samples were obtained in the range between 34 to 37emu.g-1. The magnetic coercivity (Hc) was achieved of 0.012kOe (12Oe) for the non-doped sample (YNd-0) and then increase with the addition of neodymium concentration. The increase in Hc for all the sample series can be attributed to an enhancement of the magnetocrystalline anisotropy with anisotropic Fe2+. The variation of the reflection loss (RL) versus frequency was observed in Nd doped YIG, Y1-xNdxFe5O12 with x = 0.0 – 0.8 in the frequency range of 7 –12 GHz. The optimum reflection loss (RL) was found to be 8.66(-dB) at 9.5GHz in Y2.2Nd0.8Fe5O12 (YNd-08) for x = 0.8.
- 1 July 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 855, 52-57
Synthesis, Structure, Magnetic and Absorption Properties of Nd Doped Y3Fe5O12 Garnets Prepared by Mechanochemical Method
Neodymium substituted yttrium iron garnet (YIG) nanoparticles with compositional variation of NdxY3−xFe5O12 where x = 0.0, 0.2, 0.5 and 0.8 was prepared by mechanochemicals method using high energy milling (HEM). The characterization was done using X-rays diffractometer (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and vector network analyzer (VNA). It was found that the mechanical milling followed by sintering promotes the complete structural formation of the yttrium iron garnet (YIG) structure. The XRD patterns confirm the complete introduction of Nd3+ ion into the YIG with an addition of Nd doping concentration. nanocrystalline particles with high purity and sizes ranging from 0.12μm to 0.16μm were obtained. The magnetization value, Ms from all Nd-doped samples were obtained in the range between 34 to 37emu.g-1. The magnetic coercivity (Hc) was achieved of 0.012kOe (12Oe) for the non-doped sample (YNd-0) and then increase with the addition of neodymium concentration. The increase in Hc for all the sample series can be attributed to an enhancement of the magnetocrystalline anisotropy with anisotropic Fe2+. The variation of the reflection loss (RL) versus frequency was observed in Nd doped YIG, Y1-xNdxFe5O12 with x = 0.0 – 0.8 in the frequency range of 7 –12 GHz. The optimum reflection loss (RL) was found to be 8.66(-dB) at 9.5GHz in Y2.2Nd0.8Fe5O12 (YNd-08) for x = 0.8.