Mashadi Mashadi
Mashadi Mashadi has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Wisnu Ari Adi
Research Center for Energy Materials, National Research and Innovation Agency, Kawasan Sains Teknologi Habibie, Serpong, Indonesia
3 shared publications - Ade Mulyawan
Natl Res & Innovat Agcy, Res Ctr Adv Mat, Tangerang 15314, Indonesia
2 shared publications - Dianta Ginting
Master of Mechanical Engineering Program, Faculty of Engineering, Universitas Mercubuana, West Jakarta 11650, Indonesia
2 shared publications - Didin Sahidin Winatapura
Natl Res & Innovat Agcy, Res Ctr Adv Mat, Tangerang 15314, Indonesia
2 shared publications - Dwi Nanto
Syarif Hidayatullah State Islamic University Jakarta
2 shared publications - Jan Setiawan
Research Center for Energy Materials, National Research and Innovation Agency (BRIN), South Tangerang, Indonesia
2 shared publications
Latest Publications
- 27 October 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (43) , 435913
Effect of synthesis-induced compositional deviations on the Seebeck coefficient of Fe 2 MnAl: arc melting versus spark plasma sintering
The thermoelectric response of Fe 2 MnAl is sensitive to its chemical composition and structural characteristics, which can be influenced by the synthesis route, yet systematic understanding of processing–defect–property relationships remains limited. Here, Fe 2 MnAl, synthesized by arc melting (AM) and spark plasma sintering (SPS), is investigated through combined experimental characterization, density functional theory (DFT), and BoltzTraP2 transport calculations. DFT confirms the half-metallic character of stoichiometric Fe 2 MnAl, with a spin-down band gap of 0.43 eV and a well-defined density of states dominated by transition-metal 3 d orbitals. X-ray diffraction patterns show that both samples predominantly exhibit reflections associated with the L2 1 –type Heusler structure, indicating Fe 2 MnAl as the dominant phase. The analysis therefore focuses on the dominant Fe 2 MnAl-based phase. Compositional analysis revealed that the SPS sample was close to the nominal Fe 2 MnAl stoichiometry (Fe 2.01 Mn 1.00 Al 0.99 ), whereas the AM sample exhibited a Fe-rich and Mn/Al-deficient composition (Fe 2.31 Mn 0.89 Al 0.80 )]. The resulting differences in chemical composition and structural characteristics are accompanied by distinct thermoelectric responses: AM samples exhibit higher positive Seebeck coefficients up to ∼ 450 K, while SPS samples show earlier sign reversal near ∼ 360 K with consistently lower magnitudes. To elucidate the microscopic origin of this behavior, BoltzTraP2 calculations were performed on defect-engineered DFT supercells incorporating Fe substitution and Mn/Al vacancies. The results demonstrate that Fe enrichment and Mn/Al deficiency significantly enhance thermopower by reshaping electronic states near the Fermi level, with Fe substitution at Al sites providing the strongest effect. Although our SPS method achieves closer stoichiometric control than AM, the deviations from stoichiometry inherent to AM may facilitate defect-mediated electronic structure engineering, potentially contributing to enhanced thermopower. These findings establish a relationship between synthesis route, stoichiometric deviation, defect-induced electronic structure, and the Seebeck response of Fe 2 MnAl.
- 27 October 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (43) , 435913
Effect of synthesis-induced compositional deviations on the Seebeck coefficient of Fe 2 MnAl: arc melting versus spark plasma sintering
The thermoelectric response of Fe 2 MnAl is sensitive to its chemical composition and structural characteristics, which can be influenced by the synthesis route, yet systematic understanding of processing–defect–property relationships remains limited. Here, Fe 2 MnAl, synthesized by arc melting (AM) and spark plasma sintering (SPS), is investigated through combined experimental characterization, density functional theory (DFT), and BoltzTraP2 transport calculations. DFT confirms the half-metallic character of stoichiometric Fe 2 MnAl, with a spin-down band gap of 0.43 eV and a well-defined density of states dominated by transition-metal 3 d orbitals. X-ray diffraction patterns show that both samples predominantly exhibit reflections associated with the L2 1 –type Heusler structure, indicating Fe 2 MnAl as the dominant phase. The analysis therefore focuses on the dominant Fe 2 MnAl-based phase. Compositional analysis revealed that the SPS sample was close to the nominal Fe 2 MnAl stoichiometry (Fe 2.01 Mn 1.00 Al 0.99 ), whereas the AM sample exhibited a Fe-rich and Mn/Al-deficient composition (Fe 2.31 Mn 0.89 Al 0.80 )]. The resulting differences in chemical composition and structural characteristics are accompanied by distinct thermoelectric responses: AM samples exhibit higher positive Seebeck coefficients up to ∼ 450 K, while SPS samples show earlier sign reversal near ∼ 360 K with consistently lower magnitudes. To elucidate the microscopic origin of this behavior, BoltzTraP2 calculations were performed on defect-engineered DFT supercells incorporating Fe substitution and Mn/Al vacancies. The results demonstrate that Fe enrichment and Mn/Al deficiency significantly enhance thermopower by reshaping electronic states near the Fermi level, with Fe substitution at Al sites providing the strongest effect. Although our SPS method achieves closer stoichiometric control than AM, the deviations from stoichiometry inherent to AM may facilitate defect-mediated electronic structure engineering, potentially contributing to enhanced thermopower. These findings establish a relationship between synthesis route, stoichiometric deviation, defect-induced electronic structure, and the Seebeck response of Fe 2 MnAl.
- 31 December 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 40 (04)
Magnetic phase transition and critical behavior of La0.7Ca0.3 MnO 3 -doped titanium compound
Perovskite manganites have attracted considerable attention due to their remarkable magnetic and magnetoresistive properties, which are highly sensitive to chemical substitution and external parameters. Understanding the magnetic phase transition order and critical behavior in these materials is crucial for optimizing their functional properties and exploring fundamental magnetic interactions. In this study, we investigated the magnetic phase transition and critical behavior of the Ti-doped La[ ]Ca[ ]MnO 3 compound. A polycrystalline sample of La[ ]Ca[ ] Mn[ ]Ti[ ]O 3 was synthesized using the conventional solid-state reaction method. Isothermal magnetization measurements were performed using a vibrating sample magnetometer with applied magnetic fields ranging from 0 to 1 T at various temperatures around the Curie temperature. The critical behavior at the ferromagnetic-to-paramagnetic phase transition was analyzed using the modified Arrott plot, Kouvel–Fisher method, and critical isothermal analysis. The Banerjee criterion revealed that the magnetic transition in La[ ]Ca[ ]Mn[ ]Ti[ ]O 3 is second-order, contrasting with the first-order transition observed in the parent compound La[ ]Ca[ ]MnO 3 . The critical exponents were determined as [ ] (Curie temperature)[ ] [ ] [ ]129.66[ ]K, [ ], and [ ]. The [ ] value is consistent with mean-field theory predictions ([ ]), while [ ] approaches the three-dimensional Heisenberg model ([ ]). Scaling analysis of the magnetization data confirmed two distinct universal curves around [ ], validating the reliability of the obtained critical parameters. These findings demonstrate that Ti doping fundamentally alters the magnetic phase transition from first-order to second-order, attributed to weakened double-exchange interactions and induced local lattice distortions.
- 31 December 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 40 (04)
Magnetic phase transition and critical behavior of La0.7Ca0.3 MnO 3 -doped titanium compound
Perovskite manganites have attracted considerable attention due to their remarkable magnetic and magnetoresistive properties, which are highly sensitive to chemical substitution and external parameters. Understanding the magnetic phase transition order and critical behavior in these materials is crucial for optimizing their functional properties and exploring fundamental magnetic interactions. In this study, we investigated the magnetic phase transition and critical behavior of the Ti-doped La[ ]Ca[ ]MnO 3 compound. A polycrystalline sample of La[ ]Ca[ ] Mn[ ]Ti[ ]O 3 was synthesized using the conventional solid-state reaction method. Isothermal magnetization measurements were performed using a vibrating sample magnetometer with applied magnetic fields ranging from 0 to 1 T at various temperatures around the Curie temperature. The critical behavior at the ferromagnetic-to-paramagnetic phase transition was analyzed using the modified Arrott plot, Kouvel–Fisher method, and critical isothermal analysis. The Banerjee criterion revealed that the magnetic transition in La[ ]Ca[ ]Mn[ ]Ti[ ]O 3 is second-order, contrasting with the first-order transition observed in the parent compound La[ ]Ca[ ]MnO 3 . The critical exponents were determined as [ ] (Curie temperature)[ ] [ ] [ ]129.66[ ]K, [ ], and [ ]. The [ ] value is consistent with mean-field theory predictions ([ ]), while [ ] approaches the three-dimensional Heisenberg model ([ ]). Scaling analysis of the magnetization data confirmed two distinct universal curves around [ ], validating the reliability of the obtained critical parameters. These findings demonstrate that Ti doping fundamentally alters the magnetic phase transition from first-order to second-order, attributed to weakened double-exchange interactions and induced local lattice distortions.
- Open Access
- 1 December 2025
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 25 (6) , 1768
Sustainable Synthesis and Structural Characterization of Carbon, Graphite, Graphene Oxide, and Reduced Graphene Oxide Derived from Coconut Shells
This study explores the sustainable synthesis and structural characterization of carbon, graphite, graphene oxide (GO), and reduced graphene oxide (rGO) derived from coconut shells. The objective is to investigate the potential of biomass-based precursors to produce functional carbon materials through controlled chemical treatments. X-ray diffraction patterns of carbon and graphite exhibit broad peaks, indicating low crystallinity and amorphous characteristics, while GO and rGO show dominant peaks at 22° and 23°, corresponding to the (002) plane. Scanning electron microscopy confirms the disordered morphology of carbon and graphite, while high-resolution transmission electron microscopy reveals wrinkled GO sheets and partially restacked rGO layers. Fourier transform infrared spectra identify O−H stretching at ~3442 cm−1 in carbon and C=C stretching at 1630 cm−1 in graphite, along with various oxygen-containing functional groups in GO and rGO. Raman spectroscopy shows a sharp G band at 1580 cm−1 in graphite (ID/IG = 0.840), increased disorder in GO (ID/IG = 0.843), and partial graphitic restoration in rGO (ID/IG = 0.841). These findings confirm the successful transformation of coconut shells into valuable carbon-based materials and highlight their potential for use in sustainable energy and electronic applications.
- 1 December 2025
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 25 (6) , 1768
Open AccessSustainable Synthesis and Structural Characterization of Carbon, Graphite, Graphene Oxide, and Reduced Graphene Oxide Derived from Coconut Shells
This study explores the sustainable synthesis and structural characterization of carbon, graphite, graphene oxide (GO), and reduced graphene oxide (rGO) derived from coconut shells. The objective is to investigate the potential of biomass-based precursors to produce functional carbon materials through controlled chemical treatments. X-ray diffraction patterns of carbon and graphite exhibit broad peaks, indicating low crystallinity and amorphous characteristics, while GO and rGO show dominant peaks at 22° and 23°, corresponding to the (002) plane. Scanning electron microscopy confirms the disordered morphology of carbon and graphite, while high-resolution transmission electron microscopy reveals wrinkled GO sheets and partially restacked rGO layers. Fourier transform infrared spectra identify O−H stretching at ~3442 cm−1 in carbon and C=C stretching at 1630 cm−1 in graphite, along with various oxygen-containing functional groups in GO and rGO. Raman spectroscopy shows a sharp G band at 1580 cm−1 in graphite (ID/IG = 0.840), increased disorder in GO (ID/IG = 0.843), and partial graphitic restoration in rGO (ID/IG = 0.841). These findings confirm the successful transformation of coconut shells into valuable carbon-based materials and highlight their potential for use in sustainable energy and electronic applications.
- 25 July 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (2)
The Addition of Yttrium Ions Doping to Increase the Stability of Particle Size and its Effect on the Magnetic Properties and Reflection Loss in the Co 0.5 Ni 0.5 Ti (1− x ) Y x O 3
Yttrium‐doped nickel cobalt titanate with a nominal composition of Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 ( x = 0.0; 0.025; 0.050 and 0.075) is synthesized by the solid‐state reaction method using mechanical milling from NiO, Co 3 O 4 , Y 2 O 3 , and TiO 2 powders as raw materials in a mole ratio. The effect of Y 3+ doping on particle size stability, structural, magnetic properties, and microwave absorption characteristics of the perovskite Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 has been studied in this research. All samples are investigated using X‐ray diffraction, scanning electron microscope, energy dispersive spectroscopy, vibration sample magnetometer, and vector network analyzer. It is found that all samples show a single phase with a hexagonal structure. The presence of Y 3+ ions dopant can inhibit polygonal particles, and it is able to maintain the particle size stable. In contrast, this material's magnetic properties and microwave absorption capabilities do not experience significant changes with the presence of Y 3+ ions dopant.
- 25 July 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (2)
The Addition of Yttrium Ions Doping to Increase the Stability of Particle Size and its Effect on the Magnetic Properties and Reflection Loss in the Co 0.5 Ni 0.5 Ti (1− x ) Y x O 3
Yttrium‐doped nickel cobalt titanate with a nominal composition of Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 ( x = 0.0; 0.025; 0.050 and 0.075) is synthesized by the solid‐state reaction method using mechanical milling from NiO, Co 3 O 4 , Y 2 O 3 , and TiO 2 powders as raw materials in a mole ratio. The effect of Y 3+ doping on particle size stability, structural, magnetic properties, and microwave absorption characteristics of the perovskite Ni 0.5 Co 0.5 Ti (2‐ x ) Y x O 3 has been studied in this research. All samples are investigated using X‐ray diffraction, scanning electron microscope, energy dispersive spectroscopy, vibration sample magnetometer, and vector network analyzer. It is found that all samples show a single phase with a hexagonal structure. The presence of Y 3+ ions dopant can inhibit polygonal particles, and it is able to maintain the particle size stable. In contrast, this material's magnetic properties and microwave absorption capabilities do not experience significant changes with the presence of Y 3+ ions dopant.
- Open Access
Engineering Ultra-Low Thermal Conductivity in (Pb0.8Ge0.2Te)0.95-x(PbSe)0.05(PbS)x Quaternary Lead Chalcogenides Through PbS-Induced Phase Segregation
The shortage of tellurium and toxicity of lead are major obstacles to scaling mid-temperature thermoelectric generators. We engineer quaternary lead chalcogenides with composition (Pb0.8Ge0.2Te)0.95-x(PbSe)0.05(PbS)x (0 ≤ x ≤ 0.25), where Pb is lead, Ge is germanium, Te is tellurium, Se is selenium, S is sulfur, and x denotes the molar fraction of lead sulfide (PbS). The primary novelty lies in achieving ultra-low thermal conductivity through controlled phase segregation induced by systematic PbS incorporation. X-ray diffraction analysis reveals single-phase solid solutions up to x ≈ 0.10, with secondary PbS precipitates forming beyond this threshold. These PbS-rich phases create hierarchical microstructures that scatter phonons across multiple length scales, suppressing total thermal conductivity to 0.6 Wm−1K−1 at x = 0.15—approximately 84% lower than pristine lead telluride (PbTe) and approaching glass-like thermal conductivity values. Electrical transport measurements demonstrate sulfur’s role as an electron donor, enabling carrier-type control from p-type to n-type conduction. Despite moderate electrical power factors, the optimized composition (x = 0.20) achieves a peak dimensionless figure of merit ZT ≈ 0.34 at 650 K. This work demonstrates an effective strategy for tellurium-lean, lead-reduced thermoelectric materials through sulfur-induced phase segregation, providing practical design guidelines for sustainable waste heat recovery applications.
Open AccessEngineering Ultra-Low Thermal Conductivity in (Pb0.8Ge0.2Te)0.95-x(PbSe)0.05(PbS)x Quaternary Lead Chalcogenides Through PbS-Induced Phase Segregation
The shortage of tellurium and toxicity of lead are major obstacles to scaling mid-temperature thermoelectric generators. We engineer quaternary lead chalcogenides with composition (Pb0.8Ge0.2Te)0.95-x(PbSe)0.05(PbS)x (0 ≤ x ≤ 0.25), where Pb is lead, Ge is germanium, Te is tellurium, Se is selenium, S is sulfur, and x denotes the molar fraction of lead sulfide (PbS). The primary novelty lies in achieving ultra-low thermal conductivity through controlled phase segregation induced by systematic PbS incorporation. X-ray diffraction analysis reveals single-phase solid solutions up to x ≈ 0.10, with secondary PbS precipitates forming beyond this threshold. These PbS-rich phases create hierarchical microstructures that scatter phonons across multiple length scales, suppressing total thermal conductivity to 0.6 Wm−1K−1 at x = 0.15—approximately 84% lower than pristine lead telluride (PbTe) and approaching glass-like thermal conductivity values. Electrical transport measurements demonstrate sulfur’s role as an electron donor, enabling carrier-type control from p-type to n-type conduction. Despite moderate electrical power factors, the optimized composition (x = 0.20) achieves a peak dimensionless figure of merit ZT ≈ 0.34 at 650 K. This work demonstrates an effective strategy for tellurium-lean, lead-reduced thermoelectric materials through sulfur-induced phase segregation, providing practical design guidelines for sustainable waste heat recovery applications.
- 14 March 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 339
Radar absorbing material of Co1-xCuxFe2O4: Structural, magnetic properties and absorption characteristic
- 14 March 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 339
Radar absorbing material of Co1-xCuxFe2O4: Structural, magnetic properties and absorption characteristic
- 18 November 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (12) , 125958
Effect of anisotropy field on the resonance frequency and reflection loss shift characteristics of barium hexaferrite ceramics
For this study, a modified barium hexaferrite based microwave and radar absorbing material was used. Synthesis and characterization of BaFe(12−2x)(MnTi) x O19 (0.1 ≤ x ≤ 1.0) have been prepared by solid state reaction method. The x-ray diffraction patterns reveal that all samples only crystallized into M-type barium hexaferrite after calcination at 1200 °C. Surface morphology images show that the hexagonal flake-like particle is formed at the initial stages of the Mn-Ti substitution level. The magnetic properties measurement reveals that the variation of magnetization values may vary based on preferable site occupation of Mn4+-Ti2+ cations to replace Fe3+ cations. The significant decrease in coercive field (H c) from 3.18 kOe to 0.51 kOe with the increase of Mn-Ti substitution affected the lowering values of anisotropy field (H a ). The maximum reflection loss (RL) positions of BaFe(12−2x)(MnTi) x O19 compositional series are shifted to lower frequency range following the H a trendlines. The maximum RL value equals to 98.42% microwave absorption at 10.5 GHz has been obtained in x = 1.0 (BaFe10Mn0.5Ti0.5O19) composition.
- 18 November 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (12) , 125958
Effect of anisotropy field on the resonance frequency and reflection loss shift characteristics of barium hexaferrite ceramics
For this study, a modified barium hexaferrite based microwave and radar absorbing material was used. Synthesis and characterization of BaFe(12−2x)(MnTi) x O19 (0.1 ≤ x ≤ 1.0) have been prepared by solid state reaction method. The x-ray diffraction patterns reveal that all samples only crystallized into M-type barium hexaferrite after calcination at 1200 °C. Surface morphology images show that the hexagonal flake-like particle is formed at the initial stages of the Mn-Ti substitution level. The magnetic properties measurement reveals that the variation of magnetization values may vary based on preferable site occupation of Mn4+-Ti2+ cations to replace Fe3+ cations. The significant decrease in coercive field (H c) from 3.18 kOe to 0.51 kOe with the increase of Mn-Ti substitution affected the lowering values of anisotropy field (H a ). The maximum reflection loss (RL) positions of BaFe(12−2x)(MnTi) x O19 compositional series are shifted to lower frequency range following the H a trendlines. The maximum RL value equals to 98.42% microwave absorption at 10.5 GHz has been obtained in x = 1.0 (BaFe10Mn0.5Ti0.5O19) composition.