Prachoom Khamput
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Prachoom Khamput has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Tawich Klathae
Department of Civil Engineering, College of Industrial Technology and Management, Rajamangala University of Technology Srivijaya, Nakhon Si Thammarat 80210, Thailand
2 shared publications - Chookiat Choosakul
Department of Civil Engineering, College of Industrial Technology and Management, Rajamangala University of Technology Srivijaya, Nakhon Si Thammarat 80210, Thailand
1 shared publication - Kiatsuda Somna
Department of Civil Engineering, Faculty of Engineering and Technology, Rajamangala University of Technology Isan, Nakornratchasima 30000, Thailand
1 shared publication - Mahamasuhaimi Masae
Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Srivijaya, Songkhla 90000, Thailand
1 shared publication - Saofee Dueramae
Center of Excellence in Infrastructure Materials Research and Testing (CE-IMRT), Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Krungthep (RMUTK), Bangkok 10120, Thailand
1 shared publication
Latest Publications
- Open Access
- 13 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (22) , 12076
Mechanical and Durability Performance of Sustainable Concrete Incorporating Stone Dust as Sand Substitute and Sugarcane Bagasse Ash as Cement Replacement
This study investigates the mechanical and durability performance of sustainable concrete using stone dust (SD) and ground sugarcane bagasse ash (GSCBA) to partially replace natural sand and cement, respectively. The experimental program was conducted with concrete containing 0–40 wt% GSCBA and 100% SD were prepared and tested. The results showed that full replacement of natural sand with SD did not significantly affect compressive strength. Concrete containing 10% GSCBA and 100% SD (10GSCBA) exhibited comparable compressive strength to the control concrete (CON) up to 90 days. However, the modulus of elasticity and modulus of rupture decreased slightly with increasing GSCBA content, indicating a close correlation with compressive strength. The mix containing 40% GSCBA and 100% SD (40GSCBA) achieved a compressive strength of 42.6 MPa at 90 days, representing 91% of the CON, with acceptable durability performance. These findings demonstrate that the combined utilization of SD and GSCBA offers an innovative and eco-efficient solution for concrete production, contributing to reduced cement consumption, lower production costs, and minimized carbon emissions without necessarily affecting mechanical strength or the long-term viability of the system.
- 13 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (22) , 12076
Open AccessMechanical and Durability Performance of Sustainable Concrete Incorporating Stone Dust as Sand Substitute and Sugarcane Bagasse Ash as Cement Replacement
This study investigates the mechanical and durability performance of sustainable concrete using stone dust (SD) and ground sugarcane bagasse ash (GSCBA) to partially replace natural sand and cement, respectively. The experimental program was conducted with concrete containing 0–40 wt% GSCBA and 100% SD were prepared and tested. The results showed that full replacement of natural sand with SD did not significantly affect compressive strength. Concrete containing 10% GSCBA and 100% SD (10GSCBA) exhibited comparable compressive strength to the control concrete (CON) up to 90 days. However, the modulus of elasticity and modulus of rupture decreased slightly with increasing GSCBA content, indicating a close correlation with compressive strength. The mix containing 40% GSCBA and 100% SD (40GSCBA) achieved a compressive strength of 42.6 MPa at 90 days, representing 91% of the CON, with acceptable durability performance. These findings demonstrate that the combined utilization of SD and GSCBA offers an innovative and eco-efficient solution for concrete production, contributing to reduced cement consumption, lower production costs, and minimized carbon emissions without necessarily affecting mechanical strength or the long-term viability of the system.
- Open Access
- 21 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10786
The Development of Fiber–Cement Flat Sheets by Young and Mature Coconut Fibers to Replace Asbestos for Eco-Friendly Products
This study investigated young and mature coconut fibers as an asbestos replacement in fiber–cement flat sheets. The ratio of fiber content ranged from 5% to 9.5% in increments of 0.5% by weight of binder. Crushed rock dust (CRD) was also utilized in this study at a ratio of 50% as sand replacement. The results showed that the addition of young coconut fiber (YCF) and mature coconut fiber (MCF) in flat sheets increased with decreasing bulk density and thermal conductivity. The optimum fiber content was 6.5%–7% by weight of binder for two types of fiber with the highest modulus of rupture of 12–13 MPa. The modulus of rupture and density of fiber–cement flat sheets using YCF were higher than that of fiber–cement flat sheets using MCF, which was clarified by SEM results due to the denser structure of MCF. Moreover, the modulus of rupture was directly proportional to the modulus of elasticity in fiber–cement flat sheets.
- 21 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10786
Open AccessThe Development of Fiber–Cement Flat Sheets by Young and Mature Coconut Fibers to Replace Asbestos for Eco-Friendly Products
This study investigated young and mature coconut fibers as an asbestos replacement in fiber–cement flat sheets. The ratio of fiber content ranged from 5% to 9.5% in increments of 0.5% by weight of binder. Crushed rock dust (CRD) was also utilized in this study at a ratio of 50% as sand replacement. The results showed that the addition of young coconut fiber (YCF) and mature coconut fiber (MCF) in flat sheets increased with decreasing bulk density and thermal conductivity. The optimum fiber content was 6.5%–7% by weight of binder for two types of fiber with the highest modulus of rupture of 12–13 MPa. The modulus of rupture and density of fiber–cement flat sheets using YCF were higher than that of fiber–cement flat sheets using MCF, which was clarified by SEM results due to the denser structure of MCF. Moreover, the modulus of rupture was directly proportional to the modulus of elasticity in fiber–cement flat sheets.