Ionuț Adomniței
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ionuț Adomniței has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Nicanor Cimpoesu
Faculty of Materials Science and Engineering, “Gheorghe Asachi” Technical University of Iasi, 41 Dimitrie Mangeron Blvd., 700050 Iasi, Romania
4 shared publications - Daniela Lucia Chicet
Materials Science Department, Materials Science and Engineering Faculty, Gheorghe Asachi Technical University of Iasi, 700050 Iasi, Romania
3 shared publications - Costica Bejinariu
Faculty of Materials Science and Engineering, “Gheorghe Asachi” Technical University of Iasi, 41 Dimitrie Mangeron Blvd., 700050 Iasi, Romania
2 shared publications - Gheorghe Bădărău
Faculty of Materials Science and Engineering, “Gheorghe Asachi” Technical University of Iasi, 41 Dimitrie Mangeron Blvd., 700050 Iasi, Romania
2 shared publications - Liviu Andrușcă
Faculty of Mechanical Engineering, “Gheorghe Asachi” Technical University of Iasi, 43 Dimitrie Mangeron Blvd., 700050 Iasi, Romania
2 shared publications - Marian Luțcanu
Materials Science Department, Faculty of Materials Science and Engineering, “Gheorghe Asachi” Technical University of Iasi, 71, Prof. Dr. Docent Dimitrie Mangeron Street, 700050 Iasi, Romania
2 shared publications
Latest Publications
- Open Access
Behavior of YSZ (High Y2O3 Content) Layer on Inconel to Electro-Chemical Corrosion
The high yttria content of a stabilized zirconia (YSZ) (38 wt% Y2O3) coating was deposited by atmospheric plasma spraying (APS) from Metco 207 powders on an Inconel 718 (Ni-based superalloy) substrate. As a metal coating connection, a layer of cermet powder (Ni-20% Al—410NS) was used before the ceramic layer deposition. The electro-chemical corrosion resistance of these materials was tested using Inconel cylinders with a diameter of 10 mm and a thickness of 1 mm, with and without the ceramic layer. Linear and cyclic measurements were obtained in H2SO4 electrolyte media at pH = 2. Electro-impedance spectroscopy (EIS) experiments were performed on the sample covered with the ceramic layer to evaluate the interface behavior. Scanning electron microscopy (SEM), along with equipment to determine chemical composition, and an energy dispersive spectrometry (EDS) detector were used to characterize the material surface before and after corrosion tests. It was observed that the corrosion resistance of Inconel was influenced by the bonding layer and the ceramic coating.
Open AccessBehavior of YSZ (High Y2O3 Content) Layer on Inconel to Electro-Chemical Corrosion
The high yttria content of a stabilized zirconia (YSZ) (38 wt% Y2O3) coating was deposited by atmospheric plasma spraying (APS) from Metco 207 powders on an Inconel 718 (Ni-based superalloy) substrate. As a metal coating connection, a layer of cermet powder (Ni-20% Al—410NS) was used before the ceramic layer deposition. The electro-chemical corrosion resistance of these materials was tested using Inconel cylinders with a diameter of 10 mm and a thickness of 1 mm, with and without the ceramic layer. Linear and cyclic measurements were obtained in H2SO4 electrolyte media at pH = 2. Electro-impedance spectroscopy (EIS) experiments were performed on the sample covered with the ceramic layer to evaluate the interface behavior. Scanning electron microscopy (SEM), along with equipment to determine chemical composition, and an energy dispersive spectrometry (EDS) detector were used to characterize the material surface before and after corrosion tests. It was observed that the corrosion resistance of Inconel was influenced by the bonding layer and the ceramic coating.
- Open Access
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Alloys, Co,p. 378-381
Obtaining and characterization of high-yttria content zirconia coatings
Ceramic coatings are regarded as suitable materials for high-temperature applications due to their excellent stability, both mechanical and chemical. Zirconia stabilized with yttria is a material that presents many advantages when used as a bulk or coating material in applications where exposure to high temperatures is a factor. The atmospheric plasma spraying technique was utilized in the fabrication of ceramic coatings, characterized by elevated yttria content and stabilized zirconia, on metallic substrates. The structural, chemical and mechanical properties of the coatings were investigated through a range of analytical methods, including scanning electron microscopy (SEM - SE detector), energy dispersive spectroscopy (EDS - automatic and mapping) and tribo-indenter equipment (indentation and scratch). The fabrication process was successful in producing homogenous ceramic layers with a thickness of 150 mm.
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Alloys, Co,p. 378-381
Open AccessObtaining and characterization of high-yttria content zirconia coatings
Ceramic coatings are regarded as suitable materials for high-temperature applications due to their excellent stability, both mechanical and chemical. Zirconia stabilized with yttria is a material that presents many advantages when used as a bulk or coating material in applications where exposure to high temperatures is a factor. The atmospheric plasma spraying technique was utilized in the fabrication of ceramic coatings, characterized by elevated yttria content and stabilized zirconia, on metallic substrates. The structural, chemical and mechanical properties of the coatings were investigated through a range of analytical methods, including scanning electron microscopy (SEM - SE detector), energy dispersive spectroscopy (EDS - automatic and mapping) and tribo-indenter equipment (indentation and scratch). The fabrication process was successful in producing homogenous ceramic layers with a thickness of 150 mm.
- Open Access
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Invited le,p. 21-24
Characterization of ceramic coatings with thermal barrier role obtained by atmospheric plasma jet spraying
This paper presents the characterization of ceramic thermal barrier coatings (TBCs) obtained by atmospheric plasma spraying (APS), focusing on their functional, structural, and chemical performance under extreme thermal conditions. The study highlights the critical requirements of TBC systems, including low thermal conductivity, high phase stability above 1200 °C, resistance to thermal shock, and strong adhesion between the ceramic top coat, bond coat, and metallic substrate. Special attention is given to YSZ (zirconia stabilized with yttria) coatings with a high yttria content (38 wt% Y₂O₃), which ensure cubic phase stabilization and enhanced durability at elevated temperatures. Recent advances in TBC design are discussed, such as optimized ceramic compositions, controlled microstructures, and multifunctional architectures that integrate chemical protection and sensing capabilities. The advantages of ceramic TBCs compared to massive or non-ceramic barriers are also outlined, emphasizing their reduced weight, improved thermal insulation, chemical stability, and thermomechanical compatibility. These results confirm the potential of advanced YSZ-based coatings to provide reliable thermal protection in aerospace and energy applications, contributing to increased efficiency and reduced environmental impact.
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Invited le,p. 21-24
Open AccessCharacterization of ceramic coatings with thermal barrier role obtained by atmospheric plasma jet spraying
This paper presents the characterization of ceramic thermal barrier coatings (TBCs) obtained by atmospheric plasma spraying (APS), focusing on their functional, structural, and chemical performance under extreme thermal conditions. The study highlights the critical requirements of TBC systems, including low thermal conductivity, high phase stability above 1200 °C, resistance to thermal shock, and strong adhesion between the ceramic top coat, bond coat, and metallic substrate. Special attention is given to YSZ (zirconia stabilized with yttria) coatings with a high yttria content (38 wt% Y₂O₃), which ensure cubic phase stabilization and enhanced durability at elevated temperatures. Recent advances in TBC design are discussed, such as optimized ceramic compositions, controlled microstructures, and multifunctional architectures that integrate chemical protection and sensing capabilities. The advantages of ceramic TBCs compared to massive or non-ceramic barriers are also outlined, emphasizing their reduced weight, improved thermal insulation, chemical stability, and thermomechanical compatibility. These results confirm the potential of advanced YSZ-based coatings to provide reliable thermal protection in aerospace and energy applications, contributing to increased efficiency and reduced environmental impact.
- Open Access
- 24 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10877
Electrochemical Corrosion Resistance of Al2O3–YSZ Coatings on Steel Substrates
Ceramic materials as coatings are known to have very good corrosion resistance properties compared to metallic or organic coatings, regardless of environmental conditions. The following samples were used for the experiments: an initial steel substrate and Al2O3 + YSZ (12.5%; 25% and 37.5% wt) atmospheric plasma spray-coated samples. The open circuit potential showed similar average values for all samples coated with ceramic layers, which were slightly higher than the potential of the original uncoated sample. The corrosion current densities (icorr) of all plasma jet sputter-coated systems were very similar and significantly lower than those of the original material. Corrosion rates were much lower in the coated systems due to the chemical inertness of the ceramic coatings, particularly alumina- and zirconia-based coatings. It was observed that ceramic layers improve the corrosion resistance of the metallic material, especially at higher percentages of YSZ in the plasma spray-deposited complex layer. The porosity of the sputter-deposited layers reduced their corrosion resistance due to the contact between the electrolyte solution and the metal substrate created by the interconnection of the pores. The complex equivalent electrical circuit chosen for the analysis of the values led to results in accordance with the experimental parameters.
- 24 November 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (23) , 10877
Open AccessElectrochemical Corrosion Resistance of Al2O3–YSZ Coatings on Steel Substrates
Ceramic materials as coatings are known to have very good corrosion resistance properties compared to metallic or organic coatings, regardless of environmental conditions. The following samples were used for the experiments: an initial steel substrate and Al2O3 + YSZ (12.5%; 25% and 37.5% wt) atmospheric plasma spray-coated samples. The open circuit potential showed similar average values for all samples coated with ceramic layers, which were slightly higher than the potential of the original uncoated sample. The corrosion current densities (icorr) of all plasma jet sputter-coated systems were very similar and significantly lower than those of the original material. Corrosion rates were much lower in the coated systems due to the chemical inertness of the ceramic coatings, particularly alumina- and zirconia-based coatings. It was observed that ceramic layers improve the corrosion resistance of the metallic material, especially at higher percentages of YSZ in the plasma spray-deposited complex layer. The porosity of the sputter-deposited layers reduced their corrosion resistance due to the contact between the electrolyte solution and the metal substrate created by the interconnection of the pores. The complex equivalent electrical circuit chosen for the analysis of the values led to results in accordance with the experimental parameters.