LALiviu Andrușcă

Liviu Andrușcă

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Liviu Andrușcă has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Proposed System for Temperature Measurement During Tensile Testing

    by Marius Andrei Mihalache, Vasile Merticaru, Vasile Ermolai, Liviu Andrusca, Nicanor Cimpoesu, Florin Negoescu

    Integration of thermographic imaging with in situ scanning electron microscopy (SEM) analysis may aid in quantifying thermal–mechanical behavior during tensile testing of 3D-printed polymers, which gives information about fracture mechanics, including the associated thermal phenomena. Upon fracture, samples exhibit changes in the thermal field, which is interesting because temperature fluctuations can affect material integrity. The paper introduces printing parameters to demonstrate a thermal measurement system’s sensitivity in detecting variations in mechanical response due to controlled changes in the process. Employing scientific methods, one can extrapolate results to a wider class of materials such as thermoplastics. Analysis of variance (ANOVA) is key in the design of experiments (DOE) if one wants to analyze the effect of factors and interactions. It has been used with the purpose of reducing the risk of type I errors (i.e., false positives). The finite element method (FEM) highlights temperature distribution in the area of interest and confirms recorded data. The particularly developed research experiments are carried out in a laboratory environment. Different samples are subjected to tensile tests under the evaluation of changes in the thermal field. SEM analysis is also widely used in fracture analysis to understand failure modes (ductile vs. brittle, crazing, delamination, and others). Thus, the paper aims to present a custom setup comprised a thermal camera pointed at samples during tensile testing that would serve as a reliable assessment system that accounts for the substitution of a sensor-based environment but is still fully capable of validating the measurement approach.

  • Open Access

    Influence of the Deformation Degree of Combined Loadings on the Structural and Mechanical Properties of Stainless Steels

    by Magdalena Gabriela Huțanu, Liviu Andrușcă, Marcelin Benchea, Mihai-Adrian Bernevig, Dragoș Cristian Achiței, Ștefan-Constantin Lupescu, Gheorghe Bădărău, Nicanor Cimpoeșu

    Stainless steels have many practical applications requiring various mechanical or chemical demands in the working environment. By optimizing a device used in mechanical experiments for torsional loading, several cylindrical samples were tested (both ends twisted with the same torque value in opposite directions) of 316L stainless steel (SS) to evaluate changes in the structural, chemical, and mechanical characteristics. Initially, the experimental samples were pre-loaded by tension in the elastic range (6%) and then subjected to torsion (772°) at different rates: 5, 10, and 20 mm/min. The experimental sequence consisted of a combined loading protocol with an initial tensile test followed by a subsequent torsional test. Two reference tests were performed by fracturing the samples in both torsion and tension to determine the mechanical strength parameters. The macro- and microstructural evolution of the samples as a function of the torsional degree was followed by scanning electron microscopy. The microhardness modification of the material was observed because of the strain (the microhardness variation from the center of the disk sample to the edge was also monitored). Structurally, all samples showed grain size changes because of torsional/compressive deformation zones and an increase in the degree of grain boundary misorientation. From the tensile and torsional behaviors of 316L SS and the structural results obtained, it was concluded that these materials are suitable for complex stress states in the elasto-plastic range through tensile and torsion. A reduction in Young’s modulus of up to four times the initial value at medium and high stress rates was observed when complex stresses were applied.

  • Open Access

    Behavior of YSZ (High Y2O3 Content) Layer on Inconel to Electro-Chemical Corrosion

    by Ionut Adomniței, Ramona Cimpoeșu, Daniela Lucia Chicet, Margareta Coteață, Fabian Cezar Lupu, Costică Bejinariu, Liviu Andrușcă, Petronela Paraschiv, Mihai Axinte, Gheorghe Bădărău, et al.

    The high yttria content of a stabilized zirconia (YSZ) (38 wt% Y2O3) coating was deposited by atmospheric plasma spraying (APS) from Metco 207 powders on an Inconel 718 (Ni-based superalloy) substrate. As a metal coating connection, a layer of cermet powder (Ni-20% Al—410NS) was used before the ceramic layer deposition. The electro-chemical corrosion resistance of these materials was tested using Inconel cylinders with a diameter of 10 mm and a thickness of 1 mm, with and without the ceramic layer. Linear and cyclic measurements were obtained in H2SO4 electrolyte media at pH = 2. Electro-impedance spectroscopy (EIS) experiments were performed on the sample covered with the ceramic layer to evaluate the interface behavior. Scanning electron microscopy (SEM), along with equipment to determine chemical composition, and an energy dispersive spectrometry (EDS) detector were used to characterize the material surface before and after corrosion tests. It was observed that the corrosion resistance of Inconel was influenced by the bonding layer and the ceramic coating.


  • Open Access

    Wear resistance of as-cast ZnMg-Y biodegradable alloy

    by Alexandra-Tamara Șutic, Cătălin Panaghie, Viorel Paleu, Ramona Cimpoeșu, Ana-Maria Roman, Margareta Coteață, Liviu Andrușcă, Gheorghe Bădărău, Petronela Paraschiv, Nicanor Cimpoeșu

    Biodegradable metallic materials offer a viable option for numerous medical devices where mechanical support of the implant is not required indefinitely. In some practical applications, biocompatible/biodegradable metallic elements are mechanically stressed by contact friction, compression, shear, or tensile forces. Metal samples (50x10x3 mm) were fabricated from cast ZnMgY ingots. An Amsler machine was used to apply frictional stress to the samples by placing the test specimen at the upper point of the tribological contact of the machine. The rotating element of the mechanical equipment is made of bearing steel (ASTM A295). During the friction testing of the experimental ZnMgY samples, the frictional torque was recorded using tensiometric measurements in conjunction with a Vishay P3 strain gage (Vishay, Germany). The recorded values were further processed by Savitzky-Golay filtering. Wear tests (20 N and 30 N load applied) lasted 1800 s at a constant low disc speed of 100 rpm and were performed in dry mode. Scanning electron microscopy (SEM 2D and 3D) and energy-dispersive X-ray spectroscopy (EDS) were used to evaluate wear marks.


  • Open Access

    Electrochemical Corrosion Resistance of Al2O3–YSZ Coatings on Steel Substrates

    by Ramona Cimpoeșu, Marian Luțcanu, Alin Marian Cazac, Ionuț Adomniței, Costică Bejinariu, Liviu Andrușcă, Marius Prelipceanu, Lucian-Ionel Cioca, Daniela Lucia Chicet, Ancuța Mirela Radu, et al.

    Ceramic materials as coatings are known to have very good corrosion resistance properties compared to metallic or organic coatings, regardless of environmental conditions. The following samples were used for the experiments: an initial steel substrate and Al2O3 + YSZ (12.5%; 25% and 37.5% wt) atmospheric plasma spray-coated samples. The open circuit potential showed similar average values for all samples coated with ceramic layers, which were slightly higher than the potential of the original uncoated sample. The corrosion current densities (icorr) of all plasma jet sputter-coated systems were very similar and significantly lower than those of the original material. Corrosion rates were much lower in the coated systems due to the chemical inertness of the ceramic coatings, particularly alumina- and zirconia-based coatings. It was observed that ceramic layers improve the corrosion resistance of the metallic material, especially at higher percentages of YSZ in the plasma spray-deposited complex layer. The porosity of the sputter-deposited layers reduced their corrosion resistance due to the contact between the electrolyte solution and the metal substrate created by the interconnection of the pores. The complex equivalent electrical circuit chosen for the analysis of the values led to results in accordance with the experimental parameters.


  • Open Access

    Punching Accuracy in the Case of Square-Shaped Holes

    by Gheorghe Nagîț, Andrei Marius Mihalache, Irina Beșliu-Băncescu, Oana Dodun, Liviu Andrușcă, Adelina Hrițuc, Sergiu Constantin Olaru, Laurențiu Slatineanu

    Currently, some parts made from workpieces in the form of sheets or strips are obtained by applying piercing processes. In the research whose results are presented in the article, square-shaped holes were made to evaluate the piercing accuracy of the surfaces generated by piercing in sheets of three different metal materials (carbon steel 1.033, aluminum alloy AlMg3, and stainless steel X5CrNi18-10) with different thicknesses. Apart from the nature of the material, the thickness of the sheet, the size of the clearance between the puncher and the die, and the average speed of the puncher were considered as input factors in the piercing process. The output parameters tracked were the size of the side of the square-shaped hole and the height of the burr generated by the cut. The experimental results were mathematically processed using special software, obtaining empirical mathematical models that highlight the influence of the input factors considered on the deviation of the side size of the square-shaped hole and the burr height. The analysis of the results showed that the intended size of the square hole side exerts the strongest influence on the piercing accuracy. The factor with the most significant influence on the height of the burr is the clearance between the puncher and the die.


  • Open Access

    Preliminary Investigation on Mechanical Properties of Polymer Coating Screws for the Future Fragility Fracture Fixation

    by Alexandru Filip, Oana Viola Badulescu, Paul Dan Sirbu, Bogdan Veliceasa, Bogdan Puha, Ionut Alin Pascal, Liviu Andrusca, Stefan Oprea, Cristiana Filip, Ovidiu Alexa

    Alexandru Filip, Oana Viola Badulescu, Paul Dan Sirbu, Bogdan Veliceasa, Bogdan Puha, Ionut Alin Pascal, Liviu Andrusca, Stefan Oprea, Cristiana Filip, Ovidiu Alexa - Preliminary Investigation on Mechanical Properties of Polymer Coating Screws for the Future Fragility Fracture Fixation


  • Open Access

    Experimental characterization of materials subjected to combined loading conditions

    by L Andrusca, V Goanta, P D Barsanescu, A Savin

    In real life experience, machine and structure elements are subjected to complex loading history. Combined loading testes facilitate the understanding of materials behavior subjected to multiaxial stress state. In this paper are presented experimental investigations used to evaluate the influence of an initial type of loading on material properties which will be subsequently tested through another load type. Initial tests are tension tests, by different elongations, and subsequent tests are torsion tests, until break. Circular cross section specimens will be used in these tests. Tension tests have been performed on a universal testing machine. Subsequently torsion tests have been conducted through an attachable device. It was found that the energy associated with plastic deformation obtained by subsequent torsional tests has the dominant influence on the material total plastic energy, although initial test was tension.


  • Open Access

    Numerical and experimental study of cruciform specimens subjected to biaxial tensile test

    by L Andrusca, V Goanta, P D Barsanescu, R Steigmann

    Multiaxial stress states are very common in engineering applications. To obtain a plane stress state in a material are used different experimental procedures. Biaxial tensile tests of cruciform specimens represent one of the most versatile techniques with accurate results for a wide range of materials. Specimen geometry and size must be adapted to biaxial experiments that use devices attached to universal testing machine. Biaxial tensile tests are performed using cruciform specimens optimized by a numerical study through finite element analysis and a custom built attachable device developed. The results obtained show that the method proposed in this paper can be used with good results to characterize the behaviour of ductile materials.