Arturo S. Leon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Arturo S. Leon has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Christopher Gifford-Miears
Graduate Research Assistant, School of Civil and Construction Engineering, Oregon State Univ., 231 Owen Hall, Corvallis, OR 97331-3212
2 shared publications - Elizabeth A. Kanashiro
Hydraulic Engineer, Ausenco-Vector, Calle Esquilache 371, San Isidro, Lima, Perú
2 shared publications - Juan A. González-Castrom
Graduate Research Assistant, Michigan Technological University, Civil and Environmental Engineering Department, Houghton, MI 49931
2 shared publications - Rachelle Valverde
School of Civil and Construction Engineering, Oregon State University 220 Owen Hall, Corvallis, OR 97331-3212, USA
2 shared publications - Sourabh V. Apte
School of Mechanical, Industrial, and Manufacturing Engineering , Oregon State University , Corvallis , OR 97330 , USA
2 shared publications - Yun Ji Choi
Graduate Student, School of Civil and Construction Engineering, Oregon State University, 233 Owen Hall, Corvallis, OR 97331
2 shared publications
Latest Publications
- 16 May 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 202-211
A One-Dimensional Numerical Model to Predict Pressure and Velocity Oscillations of a Compressed Air Pocket in a Vertical Shaft Filled with Water
A sewer geyser is an explosive overflow of a mixture of gas and water through a vertical pipe of a sewer system. According to reported field observations, the explosive overflows occurred in a form of ejecting water columns that persisted for several seconds. In previous studies, the presence of entrapped air pockets in sewer systems were argued to be the direct cause of the sewer geyser occurrence. The mechanisms of air-water interaction in a vertical pipe during a sewer geyser lease were investigated. A one-dimensional numerical model was developed to simulate the flow. The vertical shaft was closed at the bottom and open to the ambient pressure at the top. Initially, the lower section of the vertical shaft was filled with compressed air and the water column sat above the air pocket. Once the simulation was triggered, the interaction between the pressurized air and the water column exhibited an oscillatory motion which decayed over time. The results were compared with three dimensional numerical simulations conducted using a commercial computational fluid dynamics software.
- 16 May 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 202-211
A One-Dimensional Numerical Model to Predict Pressure and Velocity Oscillations of a Compressed Air Pocket in a Vertical Shaft Filled with Water
A sewer geyser is an explosive overflow of a mixture of gas and water through a vertical pipe of a sewer system. According to reported field observations, the explosive overflows occurred in a form of ejecting water columns that persisted for several seconds. In previous studies, the presence of entrapped air pockets in sewer systems were argued to be the direct cause of the sewer geyser occurrence. The mechanisms of air-water interaction in a vertical pipe during a sewer geyser lease were investigated. A one-dimensional numerical model was developed to simulate the flow. The vertical shaft was closed at the bottom and open to the ambient pressure at the top. Initially, the lower section of the vertical shaft was filled with compressed air and the water column sat above the air pocket. Once the simulation was triggered, the interaction between the pressurized air and the water column exhibited an oscillatory motion which decayed over time. The results were compared with three dimensional numerical simulations conducted using a commercial computational fluid dynamics software.
- 16 May 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 224-233
New Evidence on the Causes of Explosives Geysers in Stormwater and Combined Sewer Systems: A Simplified Model for the Prediction of These Geysers
A geyser in a stormwater (SW) and combined sewer system (CSS) is a high frequency oscillatory release of a mixture of gas and liquid that occurs at vertical shafts and other relief points. The oscillating jet of gas-liquid mixtures may reach a height of the order of a few to tens of meters above ground level. A considerable number of hypotheses were formulated for the causes of these geysers. Using actual geyser formulations, it is not clear how to predict a large geyser height as observed in actual stormwater and combined sewer systems. This paper describes a new theory on the causes of geyser occurrence and presents a simplified model for quantifying geyser eruption based on simultaneous exsolution of multiple gases. This model was applied to a geysering event in a stormwater collection system in Minneapolis.
- 16 May 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 224-233
New Evidence on the Causes of Explosives Geysers in Stormwater and Combined Sewer Systems: A Simplified Model for the Prediction of These Geysers
A geyser in a stormwater (SW) and combined sewer system (CSS) is a high frequency oscillatory release of a mixture of gas and liquid that occurs at vertical shafts and other relief points. The oscillating jet of gas-liquid mixtures may reach a height of the order of a few to tens of meters above ground level. A considerable number of hypotheses were formulated for the causes of these geysers. Using actual geyser formulations, it is not clear how to predict a large geyser height as observed in actual stormwater and combined sewer systems. This paper describes a new theory on the causes of geyser occurrence and presents a simplified model for quantifying geyser eruption based on simultaneous exsolution of multiple gases. This model was applied to a geysering event in a stormwater collection system in Minneapolis.
- 27 June 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 1465-1474
A Real Options-Based Framework to Evaluate Investments in River Flood Control under Uncertainty
Making decisions for flood control investment is challenging. This difficulty is because of some of the variables involved in the problem have uncertainty in them. Real Options theory is an approach to handle future uncertainties in risk management by providing flexibility in investment decisions. This work presents a real options-based framework to evaluate the financial value of having flexibility for deciding the time of investment in flood control. The framework considers the uncertainty associated with future water discharge events. Extreme water discharges are responsible for flooding events. The water discharges are considered as the random variable. The historical information of these variables is used to estimate the probability of future events. A lattice of options based in the probability of future events of the random variable is built. The option of delaying the investment is analyzed by calculating the payoffs of cost and benefits of each option. A hypothetical application is presented to validate the effectiveness of the proposed model. The result shows an option with an optimum investment time for flood control.
- 27 June 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 1465-1474
A Real Options-Based Framework to Evaluate Investments in River Flood Control under Uncertainty
Making decisions for flood control investment is challenging. This difficulty is because of some of the variables involved in the problem have uncertainty in them. Real Options theory is an approach to handle future uncertainties in risk management by providing flexibility in investment decisions. This work presents a real options-based framework to evaluate the financial value of having flexibility for deciding the time of investment in flood control. The framework considers the uncertainty associated with future water discharge events. Extreme water discharges are responsible for flooding events. The water discharges are considered as the random variable. The historical information of these variables is used to estimate the probability of future events. A lattice of options based in the probability of future events of the random variable is built. The option of delaying the investment is analyzed by calculating the payoffs of cost and benefits of each option. A hypothetical application is presented to validate the effectiveness of the proposed model. The result shows an option with an optimum investment time for flood control.
- 29 May 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 1535-1548
Three-Dimensional Numerical Modeling of Air-Water Geyser Flows
A geyser in a closed conduit system is characterized by an explosive release of a mixture of air and water through a drop shaft. Geysers are often observed in combined sewer systems (CSSs) as an explosive form of combined sewer overflows (CSOs). In the present work, the flow characteristics of sewer geyser phenomenon are studied numerically using a three-dimensional computational fluid dynamics (CFD) model for the first time. Traditionally, investigations of flow processes associated with sewer geysers are conducted through physical experiments and one or two-dimensional numerical models. However, sewer geysers are undeniably three-dimensional, hence 3D models are necessary to gain further understanding of the phenomena. The CFD model was calibrated using an experiment that exhibit characteristics of sewer geysers.
- 29 May 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 1535-1548
Three-Dimensional Numerical Modeling of Air-Water Geyser Flows
A geyser in a closed conduit system is characterized by an explosive release of a mixture of air and water through a drop shaft. Geysers are often observed in combined sewer systems (CSSs) as an explosive form of combined sewer overflows (CSOs). In the present work, the flow characteristics of sewer geyser phenomenon are studied numerically using a three-dimensional computational fluid dynamics (CFD) model for the first time. Traditionally, investigations of flow processes associated with sewer geysers are conducted through physical experiments and one or two-dimensional numerical models. However, sewer geysers are undeniably three-dimensional, hence 3D models are necessary to gain further understanding of the phenomena. The CFD model was calibrated using an experiment that exhibit characteristics of sewer geysers.
- 1 April 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 139 (4) , 374-384
Well-Balanced Scheme for Modeling Open-Channel and Surcharged Flows in Steep-Slope Closed Conduit Systems
The model presented in this paper preserves lake at rest conditions in sloped prismatic conduits. These schemes are based on the two-governing equation model in which open-channel flows are simulated using the Saint-Venant equations and pressurized flows using the compressible water hammer equations. The model in this paper preserves lake at rest conditions (horizontal still water) regardless of the conduit slope, resolves moving jump discontinuities over dry beds in sloped conduits, and resolves small perturbations from steady states, even when adjacent to dry regions. The preserving steady-state capability of this model is of particular importance in continuous long simulations when the conduits are relatively steep (. Two main contributions are presented in this paper, namely, (1) a new method for water stage reconstruction is presented that preserves lake at rest conditions regardless of the pipe slope, and (2) a horizontal system of coordinates, instead of the commonly used inclined coordinate system, is used for facilitating the implementation of the proposed well-balanced scheme to complex systems. In the horizontal coordinate system, the cross section of a circular pipe becomes an ellipse. The hydraulic characteristics of an ellipse are presented. Good results are achieved in the test cases.- 1 April 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 139 (4) , 374-384
Well-Balanced Scheme for Modeling Open-Channel and Surcharged Flows in Steep-Slope Closed Conduit Systems
The model presented in this paper preserves lake at rest conditions in sloped prismatic conduits. These schemes are based on the two-governing equation model in which open-channel flows are simulated using the Saint-Venant equations and pressurized flows using the compressible water hammer equations. The model in this paper preserves lake at rest conditions (horizontal still water) regardless of the conduit slope, resolves moving jump discontinuities over dry beds in sloped conduits, and resolves small perturbations from steady states, even when adjacent to dry regions. The preserving steady-state capability of this model is of particular importance in continuous long simulations when the conduits are relatively steep (. Two main contributions are presented in this paper, namely, (1) a new method for water stage reconstruction is presented that preserves lake at rest conditions regardless of the pipe slope, and (2) a horizontal system of coordinates, instead of the commonly used inclined coordinate system, is used for facilitating the implementation of the proposed well-balanced scheme to complex systems. In the horizontal coordinate system, the cross section of a circular pipe becomes an ellipse. The hydraulic characteristics of an ellipse are presented. Good results are achieved in the test cases.- 1 March 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 139 (3) , 284-295
Fast Approach for Unsteady Flow Routing in Complex River Networks Based on Performance Graphs
This paper presents a new model for unsteady flow routing through dendritic and looped river networks based on performance graphs. The model builds on the application of a hydraulic performance graph (HPG) to unsteady flow routing introduced in a previous study and adopts the volume performance graph (VPG) introduced in another study. The HPG of a channel reach graphically summarizes the dynamic relation between the flow through and the stages at the ends of the reach under gradually varied flow (GVF) conditions, and the VPG summarizes the corresponding storage. Both the HPG and VPG are unique to a channel reach with a given geometry and roughness and can be computed decoupled from unsteady boundary conditions by solving the GVF equation for all feasible conditions in the reach. Hence, in the proposed approach, the performance graphs can be used for different boundary conditions without the need to recompute them. Previous models based on the performance graph concept were formulated for routing through single channels or channels in series. The new approach expands on the use of HPG/VPGs and adds the use of rating performance graphs for unsteady flow routing in dentritic and looped networks. The applicability of the proposed model to subcritical unsteady flow routing is exemplified through a looped network, and its simulation results are contrasted with those from the well-known unsteady Hydrologic Engineering Centers River Analysis System model. The results show that the present extension of application of the HPG/VPGs appears to inherit the robustness of the HPG routing approach in a previous study. The unsteady flow model based on performance graphs presented in this paper can be extended to include supercritical flows.
- 1 March 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 139 (3) , 284-295
Fast Approach for Unsteady Flow Routing in Complex River Networks Based on Performance Graphs
This paper presents a new model for unsteady flow routing through dendritic and looped river networks based on performance graphs. The model builds on the application of a hydraulic performance graph (HPG) to unsteady flow routing introduced in a previous study and adopts the volume performance graph (VPG) introduced in another study. The HPG of a channel reach graphically summarizes the dynamic relation between the flow through and the stages at the ends of the reach under gradually varied flow (GVF) conditions, and the VPG summarizes the corresponding storage. Both the HPG and VPG are unique to a channel reach with a given geometry and roughness and can be computed decoupled from unsteady boundary conditions by solving the GVF equation for all feasible conditions in the reach. Hence, in the proposed approach, the performance graphs can be used for different boundary conditions without the need to recompute them. Previous models based on the performance graph concept were formulated for routing through single channels or channels in series. The new approach expands on the use of HPG/VPGs and adds the use of rating performance graphs for unsteady flow routing in dentritic and looped networks. The applicability of the proposed model to subcritical unsteady flow routing is exemplified through a looped network, and its simulation results are contrasted with those from the well-known unsteady Hydrologic Engineering Centers River Analysis System model. The results show that the present extension of application of the HPG/VPGs appears to inherit the robustness of the HPG routing approach in a previous study. The unsteady flow model based on performance graphs presented in this paper can be extended to include supercritical flows.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1687-1696
Toward the Intelligent Control of River Flooding
This paper presents a new framework for the intelligent control of river flooding. This framework links two components: river system routing (simulation) and optimization. The river system routing component builds upon the application of Performance Graphs (pre-computed hydraulics under gradually varied flow scenarios), while the optimization component uses the popular second generation multi-objective evolutionary algorithm Non-dominated Sorting Genetic Algorithm-II (NSGA-II). The use of hydraulic performance graphs for river system routing results in a robust and numerically efficient model as most of the computations for the system routing only involves interpolation steps. The proposed framework allows controlled flooding in the event that the capacity of the river system has been exceeded. This controlled flooding is based on weight factors assigned to each reach of the system depending on a hierarchy of risk to losses associated with flooding. Naturally, river reaches that are less prone to flood losses are assigned smaller weight factors and reaches that are more prone to flood losses are assigned larger weight factors. For illustration purposes, the proposed framework was applied to the Boise river system in Idaho. The results show a promising outcome in the application of this model for flood control.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1687-1696
Toward the Intelligent Control of River Flooding
This paper presents a new framework for the intelligent control of river flooding. This framework links two components: river system routing (simulation) and optimization. The river system routing component builds upon the application of Performance Graphs (pre-computed hydraulics under gradually varied flow scenarios), while the optimization component uses the popular second generation multi-objective evolutionary algorithm Non-dominated Sorting Genetic Algorithm-II (NSGA-II). The use of hydraulic performance graphs for river system routing results in a robust and numerically efficient model as most of the computations for the system routing only involves interpolation steps. The proposed framework allows controlled flooding in the event that the capacity of the river system has been exceeded. This controlled flooding is based on weight factors assigned to each reach of the system depending on a hierarchy of risk to losses associated with flooding. Naturally, river reaches that are less prone to flood losses are assigned smaller weight factors and reaches that are more prone to flood losses are assigned larger weight factors. For illustration purposes, the proposed framework was applied to the Boise river system in Idaho. The results show a promising outcome in the application of this model for flood control.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1119-1128
A Robust, Numerically Efficient Model for Unsteady Flow Routing in Topologically Complex River Networks
We present a robust and numerically efficient model for unsteady flow routing through dendritic, looped and networks comprised of dendritic and looped sub-networks. The model builds upon the application of Hydraulic Performance Graph (HPG) to unsteady flow routing introduced by González-Castro and Yen (2000) and adopts the Volume Performance Graph (VPG) introduced by Hoy and Schmidt (2006). The HPG of a channel reach graphically summarizes the dynamic relation between the flow through and the stages at the ends of the reach under gradually varied flow (GVF) conditions, while the VPG summarizes the corresponding storage. Both, the HPG and VPG are unique to a channel reach with a given geometry and roughness, and can be computed decoupled from unsteady boundary conditions by solving the GVF equation for all feasible conditions in the reach. Using HPG's and VPG's results in a robust and numerically efficient model for flow routing because the performance graphs (PG's) provide pre-computed overall GVF solutions of the momentum and mass conservation equations and the computations for routing through the system mostly involve interpolation steps. Although, the HPG/VPG approach is a highly numerically efficient and robust approach, previous routing models based on this approach were formulated for single prismatic channels or channels in series, so they are not suitable for routing through dendritic and looped networks. Our model overcomes the limitations of previous HPG/VPG formulations, as it can be used for unsteady flow routing through any river network. In our model (OSU Unsteady Routing) we solve a system of nonlinear equations assembled based on information summarized in the systems' HPG's and VPG's, continuity and compatibility conditions of water stages at the union of reaches (nodes), and the system boundary conditions. We exemplify the applicability of OSU Unsteady Routing to a looped network and contrast its simulation results with those from the well-known unsteady HEC-RAS model.
- 17 May 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1119-1128
A Robust, Numerically Efficient Model for Unsteady Flow Routing in Topologically Complex River Networks
We present a robust and numerically efficient model for unsteady flow routing through dendritic, looped and networks comprised of dendritic and looped sub-networks. The model builds upon the application of Hydraulic Performance Graph (HPG) to unsteady flow routing introduced by González-Castro and Yen (2000) and adopts the Volume Performance Graph (VPG) introduced by Hoy and Schmidt (2006). The HPG of a channel reach graphically summarizes the dynamic relation between the flow through and the stages at the ends of the reach under gradually varied flow (GVF) conditions, while the VPG summarizes the corresponding storage. Both, the HPG and VPG are unique to a channel reach with a given geometry and roughness, and can be computed decoupled from unsteady boundary conditions by solving the GVF equation for all feasible conditions in the reach. Using HPG's and VPG's results in a robust and numerically efficient model for flow routing because the performance graphs (PG's) provide pre-computed overall GVF solutions of the momentum and mass conservation equations and the computations for routing through the system mostly involve interpolation steps. Although, the HPG/VPG approach is a highly numerically efficient and robust approach, previous routing models based on this approach were formulated for single prismatic channels or channels in series, so they are not suitable for routing through dendritic and looped networks. Our model overcomes the limitations of previous HPG/VPG formulations, as it can be used for unsteady flow routing through any river network. In our model (OSU Unsteady Routing) we solve a system of nonlinear equations assembled based on information summarized in the systems' HPG's and VPG's, continuity and compatibility conditions of water stages at the union of reaches (nodes), and the system boundary conditions. We exemplify the applicability of OSU Unsteady Routing to a looped network and contrast its simulation results with those from the well-known unsteady HEC-RAS model.