Navjot Sandhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Navjot Sandhu has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Ming Zheng
University of Windsor
2 shared publications- Ming Zheng
Department of Mechanical, Automotive and Materials Engineering University of Windsor 401 Sunset Avenue N9B 3P4 Windsor ON Canada
2 shared publications - Simon LeBlanc
Department of Mechanical, Automotive, and Materials Engineering (MAME), University of Windsor , Windsor, ON N9B 3P4, Canada
2 shared publications Xiao Yu
University of Windsor
2 shared publications- Binghao Cong
Department of Mechanical, Automotive, and Materials Engineering (MAME), University of Windsor , Windsor, ON N9B 3P4, Canada
1 shared publication David S.-K. Ting
University of Windsor
1 shared publication
Latest Publications
- 20 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (9) , 1-10
Heat Release Characteristics of a Volatile, Oxygenated, and Reactive Fuel in a Direct Injection Engine
Compression ignition (CI) diesel engines offer power-dense solutions for heavy-duty vehicles. The purpose of combustion management for diesel engines primarily concerns the balance of high efficiency and low emissions. Conventional single-shot diesel combustion involves extended overlap of fuel injection and combustion, promoting diffusion combustion, which is efficient yet prone to form excessive amounts of nitrogen oxides and soot emissions. The application of exhaust gas dilution to reduce NOx below regulation limits leads to an increase in smoke emissions, further magnifying the emission control dilemma. Dimethyl ether (DME) contains suitable reactivity for compression ignition engines while also possessing distinct characteristics to diesel, notably physical properties such as volatility and high oxygen content, that eliminates engine-out soot concerns. In turn, DME enables direct NOx control via oxygen dilution. Nonetheless, the influence of charge dilution toward the combustion heat release behavior of DME persists. This study investigated heat release patterns of high-pressure DME combustion using a single-shot fuel scheduling, with injection timing fixed at top dead center (TDC). Throughout the study, the injection pressure, engine load, and oxygen dilution were adjusted separately to characterize their influence on the subsequent combustion process. Diesel combustion operated at matching conditions was used to provide relevance to the results. Most notably, the period of diffusion burning was extended in DME following a longer period of injection–combustion overlap. To add, the heat release of DME combustion was repeatedly shorter than diesel owing to the lack of end-burning combustion phase inherent to diesel combustion.
- 20 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (9) , 1-10
Heat Release Characteristics of a Volatile, Oxygenated, and Reactive Fuel in a Direct Injection Engine
Compression ignition (CI) diesel engines offer power-dense solutions for heavy-duty vehicles. The purpose of combustion management for diesel engines primarily concerns the balance of high efficiency and low emissions. Conventional single-shot diesel combustion involves extended overlap of fuel injection and combustion, promoting diffusion combustion, which is efficient yet prone to form excessive amounts of nitrogen oxides and soot emissions. The application of exhaust gas dilution to reduce NOx below regulation limits leads to an increase in smoke emissions, further magnifying the emission control dilemma. Dimethyl ether (DME) contains suitable reactivity for compression ignition engines while also possessing distinct characteristics to diesel, notably physical properties such as volatility and high oxygen content, that eliminates engine-out soot concerns. In turn, DME enables direct NOx control via oxygen dilution. Nonetheless, the influence of charge dilution toward the combustion heat release behavior of DME persists. This study investigated heat release patterns of high-pressure DME combustion using a single-shot fuel scheduling, with injection timing fixed at top dead center (TDC). Throughout the study, the injection pressure, engine load, and oxygen dilution were adjusted separately to characterize their influence on the subsequent combustion process. Diesel combustion operated at matching conditions was used to provide relevance to the results. Most notably, the period of diffusion burning was extended in DME following a longer period of injection–combustion overlap. To add, the heat release of DME combustion was repeatedly shorter than diesel owing to the lack of end-burning combustion phase inherent to diesel combustion.
- 29 November 2024
- Published by Springer Nature
- p. 119-132
Experimental Study on the Heat Release of Spherical Premixed Flames
- 29 November 2024
- Published by Springer Nature
- p. 119-132
Experimental Study on the Heat Release of Spherical Premixed Flames
- Open Access
- 20 March 2024
- Published by Scilight Press Pty Ltd in International Journal of Automotive Manufacturing and Materials
- Vol. 3 (1) , 4
Catalytic NOx Aftertreatment—Towards Ultra-Low NOx Mobility
Article Catalytic NOx Aftertreatment—Towards Ultra-Low NOx Mobility Navjot Sandhu * , Xiao Yu, and Ming Zheng Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, ON N9B 3P4, Canada * Correspondence: sandh12p@uwindsor.ca Received: 26 January 2024 Accepted: 13 March 2024 Published: 20 March 2024 The push for environmental protection and sustainability has led to strict emission regulations for automotive manufacturers as evident in EURO VII and EPA2027 requirements. The challenge lies in maintaining fuel efficiency and simultaneously reducing the carbon footprint while meeting future emission regulations. Nitrogen oxides represent one of the major and most regulated components of automotive emissions. The need to meet the stringent requirements regarding NOx emissions in both SI and CI engines has led to the development of a range of in-cylinder strategies and after-treatment techniques. In-cylinder NOx control strategies including charge dilution (fresh air and EGR), low-temperature combustion, and use of alternative fuels (as drop-in replacements or dual fuel operation) have proven to be highly effective in thermal NOx abatement. Aftertreatment methods are required to further reduce NOx emissions. Current catalytic aftertreatment systems for NOx mitigation in SI and CI engines include the three-way catalyst (TWC), selective catalytic reduction (SCR) and lean NOx trap (LNT). This review summarizes various approaches to NOx abatement in IC engines using aftertreatment catalysts. The mechanism, composition, operation parameters and recent advances in each after-treatment system are discussed in detail. The challenges to the current after-treatment scenario, such as cold start light off, catalyst poisoning and the limits of current aftertreatment solutions in relevance to the EURO VII and 2026 EPA requirements are highlighted. Lastly, recommendations are made for future aftertreatment systems to achieve ultra-low NOx emissions.
- 20 March 2024
- Published by Scilight Press Pty Ltd in International Journal of Automotive Manufacturing and Materials
- Vol. 3 (1) , 4
Open AccessCatalytic NOx Aftertreatment—Towards Ultra-Low NOx Mobility
Article Catalytic NOx Aftertreatment—Towards Ultra-Low NOx Mobility Navjot Sandhu * , Xiao Yu, and Ming Zheng Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, ON N9B 3P4, Canada * Correspondence: sandh12p@uwindsor.ca Received: 26 January 2024 Accepted: 13 March 2024 Published: 20 March 2024 The push for environmental protection and sustainability has led to strict emission regulations for automotive manufacturers as evident in EURO VII and EPA2027 requirements. The challenge lies in maintaining fuel efficiency and simultaneously reducing the carbon footprint while meeting future emission regulations. Nitrogen oxides represent one of the major and most regulated components of automotive emissions. The need to meet the stringent requirements regarding NOx emissions in both SI and CI engines has led to the development of a range of in-cylinder strategies and after-treatment techniques. In-cylinder NOx control strategies including charge dilution (fresh air and EGR), low-temperature combustion, and use of alternative fuels (as drop-in replacements or dual fuel operation) have proven to be highly effective in thermal NOx abatement. Aftertreatment methods are required to further reduce NOx emissions. Current catalytic aftertreatment systems for NOx mitigation in SI and CI engines include the three-way catalyst (TWC), selective catalytic reduction (SCR) and lean NOx trap (LNT). This review summarizes various approaches to NOx abatement in IC engines using aftertreatment catalysts. The mechanism, composition, operation parameters and recent advances in each after-treatment system are discussed in detail. The challenges to the current after-treatment scenario, such as cold start light off, catalyst poisoning and the limits of current aftertreatment solutions in relevance to the EURO VII and 2026 EPA requirements are highlighted. Lastly, recommendations are made for future aftertreatment systems to achieve ultra-low NOx emissions.
- Open Access
- 16 July 2021
- Published by ASME International
An Investigation Into OME3 on a High Compression Ratio Engine
For decades, alternative fuels have been investigated to achieve high efficiency and low emission combustion in IC engines. Oxygenated fuels such as alcohols and ethers have shown advantageous benefits for their use in engine combustion. Polyoxymethylene dimethyl ether (PODE) fuels contain a high amount of oxygen (up to 50% by mass) and improved volatility as compared to diesel. In
- 16 July 2021
- Published by ASME International
Open AccessAn Investigation Into OME3 on a High Compression Ratio Engine
For decades, alternative fuels have been investigated to achieve high efficiency and low emission combustion in IC engines. Oxygenated fuels such as alcohols and ethers have shown advantageous benefits for their use in engine combustion. Polyoxymethylene dimethyl ether (PODE) fuels contain a high amount of oxygen (up to 50% by mass) and improved volatility as compared to diesel. In