MZMing Zheng

Ming Zheng

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ming Zheng has a total of 67 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of Rate of Injection for Low Carbon Fuels in the Common-Rail Direct Injection System

    by Simon LeBlanc, Binghao Cong, Xiao Yu, Ming Zheng

    Article Simon LeBlanc, Binghao Cong, Xiao Yu, and Ming Zheng * Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, ON N9B 3P4, Canada * Correspondence: mzheng@uwindsor.ca Received: 26 March 2025; Revised: 8 April 2025; Accepted: 25 April 2025; Published: 30 April 2025 Abstract: Internal combustion engines (ICEs) powered by liquid fuels remain the dominant powertrain system for heavy-duty road transportation, benefiting from the high energy density, ease of storage and transportation, and relatively low refueling pressure of traditional liquid hydrogen carbon fuel. However, concerns over tailpipe emissions and greenhouse gas (GHG) effects have driven the search for alternative fuels with lower carbon footprints. ICEs offer a key advantage during this transition, as they can operate on a variety of fuels, enabling a flexible approach to reducing harmful emissions and GHG while maintaining reliable power output. Alternative liquid fuels, such as dimethyl ether (DME), have shown great potential in mitigating environmental impacts while ensuring sufficient engine performance. However, the significantly different physical and chemical properties of renewable fuels necessitate the adoption of tailored combustion strategies to ensure optimal engine operation. In particular, the fuel injection strategy plays a pivotal role in governing the combustion process, as it directly influences fuel-air mixing, ignition characteristics, and hence, the combustion efficiency. Therefore, detailed characterization of the fuel injection process (rate of injection (ROI) profiles, injection delay, and injection quantities) is necessary for research and development of advanced combustion strategies. In this study, the ROI profiles for diesel, DME and polyoxymethylene dimethyl ethers (OME3) were measured using the Bosch long tube method, with diesel severed as the reference fuel. Comparative tests were conducted under varying injection pressures (300 bar to 900 bar) and injection durations (0.3 ms to 3 ms) to investigate the influence of fuel properties on ROI profiles. The results revealed that all three fuels exhibited comparable ROI at injection durations below 700 µs. However, at longer injection durations and higher pressures, significant differences emerged. At a 3 ms injection duration, DME consistently showed the lowest steady-state ROI, while OME3 exhibited the highest across all injection pressures. Furthermore, the discharge coefficient (Cd) increased with injection pressure and converged across three fuels at higher pressures. This indicated that, under those conditions, fuel density became the dominant factor influencing ROI, hence the injection quantities. Internal combustion engines (ICEs) powered by liquid fuels remain the dominant powertrain system for heavy-duty road transportation, benefiting from the high energy density, ease of storage and transportation, and relatively low refueling pressure of traditional liquid hydrogen carbon fuel. However, concerns over tailpipe emissions and greenhouse gas (GHG) effects have driven the search for alternative fuels with lower carbon footprints [1,2]. Compression ignition (CI) direct injection (DI) engines offer several advantages, making them a preferred choice for heavy-duty road applications with lower carbon footprints. One of their primary benefits is their relatively high thermal efficiency, attributed to the use of high compression ratios and lean fuel-air mixtures [3]. This efficiency results in improved fuel economy and reduced carbon dioxide emissions per unit of power produced. Furthermore, the emission regulations enacted for on-road transportation vehicles are continuously tightening, driving the development and implementation of exhaust aftertreatment technology and advanced combustion strategies to manage the tailpipe emissions to permissible levels. CI engines are highly versatile, capable of running on a variety of fuels to tackle the emission challenges. Ether fuels offer compelling characteristics that present the potential to address challenges associated with clean combustion diesel engines. The high reactivity of DME makes it a suitable fuel for CI combustion, while its notably higher oxygen content can avoid the classical NOx-soot trade-off inherent to diesel-fueled CI combustion [4–8]. The inherently coupled nature of fuel injection and combustion allows precise control over the combustion process by altering the fuel injection strategy. Parameters such as injection timing, fuel quantity, and the number of injection pulses can be flexibly modified to achieve optimized combustion [9]. Such adjustments can reduce combustion noise, enhance thermal efficiency, and minimize emissions. Furthermore, post-injection strategies can be employed to facilitate after-treatment system regeneration, contributing to effective emissions management [10]. Given the critical role of fuel injection in influencing combustion characteristics, precise measurement of the rate of injection (ROI) profiles, including injection delay timing and fuel quantities, is essential. The accurate ROI data is necessary for research and development of advanced combustion strategies, enabling the development of more efficient and cleaner engine technologies. Numerous studies and extensive literature have focused on the measurement and analysis of diesel ROI. These investigations have highlighted the significant influence of the rate of injection (ROI) profiles on air-fuel mixing and combustion processes. Bai et al. [10] investigated the effects of different ROI shapes on the diesel combustion process and emissions using numerical simulation. In their study, five distinct ROI shapes were analyzed, and the results demonstrated that the shape of ROI notably affected the heat release process, leading to variations in combustion behavior and emissions. Among the investigated profiles, the trapezoidal ROI shape resulted in the lowest soot emissions while maintaining acceptable nitrogen oxide (NOx) emissions. The highest NOx emissions were produced by triangle shape ROI due to its higher peak value of ROI, leading to elevated combustion temperature. Niculate et al. [11] did a similar numerical approach to investigate the shape of ROI effects on combustion and emission. Both diesel and biodiesel were investigated and compared. The authors found that the variation in ROI shapes for diesel and biodiesel showed a similar response in the emission stand of view. They concluded that the group of injection shapes presenting a fast increase of the ROI at the beginning produces higher values of NOx emissions and lower soot emissions compared to the trapezoid shape of ROI. This is owing to the higher injection quantity in the early stage promotes pre-mixed combustion. In stark contrast, the group of injection shapes presenting a fast increase of the ROI at a later stage produces lower NOx emissions and higher soot emissions. Nishimura et al. [12] investigated the effects of different ROI patterns on combustion characteristics and emissions in a DI diesel engine. The authors utilized nozzle needle lift control to slowly lift the needle valve and thus created a gradual ramping up ROI shape. They found that the initial stage of ROI is restricted, and less pre-mixed combustion was observed in the rate of heat release curve, and the diffusion combustion occurred very slowly. However, the restricted initial ROI also mitigated the atomization and spray travel distance. As a result, the smoke emission deteriorated. As mentioned above, the diesel combustion and emission management strategies for direct injection systems depend strongly on the fuel delivery process. Thus, an accurate measurement of fuel injection processes is valuable towards the understanding and management of combustion events. However, concerns over tailpipe emissions and greenhouse gas (GHG) effects have driven the search for cleaner alternatives. Alternative compressible liquid fuels, such as dimethyl ether (DME), have shown great potential in mitigating environmental impacts while ensuring efficient engine performance. Some of these alternative fuels exhibit significantly different physical and chemical properties. This necessitates the adoption of tailored combustion strategies to ensure optimal engine operation. Lee et al. [13] investigated the injection behavior of diesel and DME using a common-rail system, finding that at short energizing durations, both fuels delivered similar quantities. However, as the energizing duration increased, diesel showed a higher injected amount. In a later study, Kim, et al. [14] further analyzed the injection characteristics of the two fuels, reporting that at a 700 μs energizing pulse, diesel’s peak injection rate was roughly 1.4 times greater than DME’s. Additionally, DME demonstrated a longer closing delay compared to diesel. Expanding on these results, the researchers tested additional injection pressures and observed trends consistent with their earlier findings [13]. Nonetheless, there remains a lack of empirical data on DME injection, and the expected injection profile of DME in diesel injectors is still not well understood. There is a noticeable lack of direct comparisons between diesel and alternative fuels like dimethyl ether DME in terms of their ROI profiles. Given the distinct physical and chemical properties of alternative fuels, understanding their injection behavior is crucial for developing accurate models and optimizing combustion strategies. In this study, the ROI profiles of diesel, OME3, and DME were measured using the Bosch long tube method. Furthermore, a comparative analysis of the injection rate profiles of these fuels across a range of testing conditions was performed. In this section, the experimental platforms employed for measuring ROI profiles for both diesel and alternative fuels are detailed, including specific methodologies and testing procedures. Two injection measurement platforms were used to measure the injection profile. The EFS injection measurement bench (EFS ITB132R) was calibrated and operated with ISO 4113 calibration fluid (engineered fluid to simulate diesel characteristics). The system can perform both dynamic ROI measurement and fuel injection quantity measurement. However, it is inconvenient to operate multiple fuels on the platform. Thus, an in-house designed long tube ROI test bench based on Bosch principle was employed to investigate the performance of a high-pressure direct injection diesel injector using various types of fuel. In a previous study [15], the authors showed that the long tube platform was applicable to measure the injection profiles of alternative fuels. In this study, both systems were used to measure the injection profiles for diesel fuel, and the results were compared. The ROI profiles for alternative fuels were investigated solely by the long tube platform. An in-house designed long tube ROI test bench based on Bosch principle was used to measure the ROI for a wide range of fuels. The long tube platform consisted of a high-pressure injection pump and a pressure measurement chamber, linked to a 50-meter-long tube (coiled into 26 turns). An overview of the ROI platform was shown in Figure 1. The fuel injection control signals were initiated using a National Instruments RT-FPGA system, which also triggers the data acquisition system. Figure 1. Experimental setup of the long tube platform. The Bosch method principally required both the chamber, and the extended tube were filled with the same liquid fuel, free from air pockets. A low-pressure diesel supply cart delivered fuel through a needle valve to fill the system. A 1-gallon reservoir was pressurized with nitrogen to around 11 bar after filling with DME, which kept the DME in a liquid state within the long tube system. A pressure gauge and a needle valve were installed to regulate the background pressure in the long tube. A set of tests was performed previous to the injector characterization to benchmark the impact of background pressure on the ROI measurement. The results revealed that a back pressure above 20 bar showed a negligible impact on the ROI measurement, as shown in Figure 2. For this work, a background pressure of 40 bar gauge (barg) was maintained. Figure 2. Background pressure effects on the rate of injection profiles. A Maximator LSF100-2 (Maxpro Technologies, Fairview, PA, USA) pneumatically driven double-air liquid pump was used to pressurize the fuel for high-pressure injection. The sealing materials (PTFE) for the pump are compatible with highly aggressive chemicals, and the pump is applicable to pressurize a number of alternative fuels. A commercial piezoelectric diesel injector with a 6 × 150 µs nozzle configuration was used in this study. The injector was fitted onto a stainless-steel chamber with a side-mounted pressure transducer. During the injection event, the transient fuel supply increased the chamber pressure promptly. The pressure curve recorded by the pressure transducer corresponds to the ROI profile. The theoretical calculation from pressure to gravimetric ROI is shown in Equation (1), as follows [16]: where A is the cross-sectional area in the measurement chamber, c is the speed of sound of the background media (test fuel), and p(i) is the measured pressure. Figure 3 shows a demonstration case for the ROI profile, injector control signals, and the derived parameters. The ROI profile can be divided into three distinct phases: the rising phase, where the injection began and ROI rapidly increased; the steady-state phase, during which fuel delivery stabilized; and the decaying phase, where the ROI gradually decreased as the injector closed. These phases corresponded closely to the dynamic response of the injector during the injection event and provided a basis for analyzing injection behavior and fuel delivery characteristics. The fuel injection timing can be determined based on the rising slope of the pressure curve, while the end of injection was challenging to determine accurately from the pressure curve because of the oscillating pressure waves. Therefore, the end of the fuel delivery slope was extended with a linear fit line. Figure 3. Fuel injection profile and parameter definition. The EFS injection measurement bench (EFS ITB132R) is a commercial injection test bench platform for injector characterization. The measurement bench is capable of measuring both the injection mass and the rate of injection profile on a shot-to-shot basis. The measurement bench consists of a closed-volume chamber measurement system (transient ROI measurement), a pressure regulation system (fuel injection pressure and backpressure regulation), and a volumetric measurement system (injection volume measurement). The ROI and total injection amount were measured with three processes in sequential order. The transient fuel injection caused an increase in pressure in the measurement chamber. The pressure was recorded by a pressure transducer and derived to the ROI profile. The slight increase in background pressure owing to the fuel injection was alleviated through an electro-valve. The fuel was then fed to a volumetric measurement system. The volumetric measurement system used a piston to measure the volume of the injected fuel. Once the injection volume measurement is obtained, the fuel is released to the reservoir. This order of process was repeated for each injection event. Several published studies [17,18] indicated that the ROI measurement results from the long tube system showed some inconsistencies with other ROI measurement systems. In this section, the ROI measurement results from the long tube platform were compared to those of the EFS platform. The difference in ROI measurement results between the two platforms was discussed. Figure 4 presents the ROI profiles at an injection pressure of 600 bar for the long tube platform and the EFS platform. The ROI profiles from both platforms aligned well, particularly in terms of injector opening and closing timing. Minor differences were observed in the transient rising stage. The long tube platform showed a slight reduction in ROI profiles around 0.5 ms. Furthermore, marginally lower maximum ROI values in the steady state were also observed in the long tube platform. As the injection duration increased, the ROI profiles maintained a consistent pattern. The opening delay exhibited minimal variation between the two systems, ranging from 260 µs to 265 µs. However, the long tube platform showed an obvious increase in closing delay with longer injection durations. Figure 4. Injection duration impact on ROI for diesel, OME3, and DME. The injection duration impact on the injection delays is shown in Figure 5. Both the long tube and EFS platforms showed similar trends, the opening delay remained relatively unchanged as the injection duration increased. The closing delay initially increased linearly with injection duration, but further extending the injection duration had little effect on the closing delay. Comparatively, the injector opening delay between the two systems showed only minor differences across the range of injection durations. However, the long tube platform consistently showed a longer closing delay. Additionally, at longer injection duration (plateau phase), the closing delay for the long tube platform exhibited slight fluctuations. As mentioned above, the closing delay determination was obtained from processed data. These post-processing effects may have contributed to the longer closing delay observed on the long tube platform. To further validate the accuracy of the injector closing time. A high-speed camera was utilized to capture the fuel spray development in a constant volume chamber. A detailed description of the constant volume chamber and imaging system can be found in [19]. Figure 5. Injection duration impact on opening delay and closing delay for diesel, OME3, and DME. Figure 6 shows the injector opening and closing timing measured by the EFS platform and by using high-speed imaging. The test was conducted at an injection pressure of 900 bar, with a 1 ms injection command duration. The injector was equipped with an 8 × 110 µm nozzle configuration. Several images corresponding to key phases of the injection event were selected to present here. Image 1 was captured when the injector signal was sent to the injector driver. It showed the background of the view before the injector opens. The fuel spray was first observed in image 2, indicating the injector opening time. A slight discrepancy in the injector opening time between the EFS platform and the high-speed camera was observed. Image 3 captured the fully developed spray during the steady-state injection phase. Image 4 showed the spray dissipation as the injector closed. By correlating the visual evidence with the EFS platform ROI data, the accuracy of the injector opening and closing times can be assessed under these test conditions. Figure 6. High-speed imaging for fuel spray development in a constant volume chamber vs. ROI measurement from the EFS platform. Figure 7 shows the injector opening and closing delays measured by the EFS platform and the high-speed imaging over an extended test condition. The blue circles represented data obtained from high-speed imaging, and the red squares represented measurements from the EFS platform. The results showed minor discrepancies in determining the injector delay, especially in the closing delay. Therefore, the closing delay obtained from the EFS platform is more reliable. Figure 7. Injector opening and closing delays were measured by the EFS platform and high-speed...


  • Plasma Resistance Control for Ignition Energy Improvements Under High-Speed Flow Conditions

    by Xiao Yu, Linyan Wang, Ming Zheng

    Modern spark ignition (SI) systems tend to face a fuel-lean mixture of elevated density and intensified flow for improving engine efficiency and exhaust emission. A more effective ignition source, e.g., a properly modulated current profile of on-demand elevated energy is preferred to assist the flame kernel formation process and developments. The strong air motion blows the plasma channel away from the spark gap, causing the plasma channel to stretch, which leads to restrike events when stretched excessively. In this work, the impact of spark plasma stretching on the discharge processes has been investigated under various flow velocities and background densities. It is observed that the cross-flow may raise the deposition efficiency of discharge energy between the spark electrodes via plasma stretching, but the prolonged stretching may challenge the plasma stability. The mechanisms of restrike and blow-off events are investigated corresponding to plasma resistance and discharge voltage. Furthermore, a boosted current strategy is applied to study the effectiveness of discharge current modulation (50 mA–3 A) on the plasma resistance control under the flow conditions. The study comprehensively investigates the impacts of discharge current, flow velocity, and background pressure on plasma stretching and energy release efficacy.

  • Heat Release Characteristics of a Volatile, Oxygenated, and Reactive Fuel in a Direct Injection Engine

    by Simon LeBlanc, Binghao Cong, Navjot Sandhu, Xiao Yu, Graham T Reader, Ming Zheng

    Compression ignition (CI) diesel engines offer power-dense solutions for heavy-duty vehicles. The purpose of combustion management for diesel engines primarily concerns the balance of high efficiency and low emissions. Conventional single-shot diesel combustion involves extended overlap of fuel injection and combustion, promoting diffusion combustion, which is efficient yet prone to form excessive amounts of nitrogen oxides and soot emissions. The application of exhaust gas dilution to reduce NOx below regulation limits leads to an increase in smoke emissions, further magnifying the emission control dilemma. Dimethyl ether (DME) contains suitable reactivity for compression ignition engines while also possessing distinct characteristics to diesel, notably physical properties such as volatility and high oxygen content, that eliminates engine-out soot concerns. In turn, DME enables direct NOx control via oxygen dilution. Nonetheless, the influence of charge dilution toward the combustion heat release behavior of DME persists. This study investigated heat release patterns of high-pressure DME combustion using a single-shot fuel scheduling, with injection timing fixed at top dead center (TDC). Throughout the study, the injection pressure, engine load, and oxygen dilution were adjusted separately to characterize their influence on the subsequent combustion process. Diesel combustion operated at matching conditions was used to provide relevance to the results. Most notably, the period of diffusion burning was extended in DME following a longer period of injection–combustion overlap. To add, the heat release of DME combustion was repeatedly shorter than diesel owing to the lack of end-burning combustion phase inherent to diesel combustion.


  • Open Access

    Combustion Management of Neat Dimethyl Ether Combustion for Enabling High Efficiency and Low NOx Production

    by Simon LeBlanc, Binghao Cong, Navjot Sandhu, Long Jin, Xiao Yu, Ming Zheng

    Article Simon LeBlanc, Binghao Cong, Navjot Sandhu, Long Jin, Xiao Yu and Ming Zheng * Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, ON N9B 3P4, Canada * Correspondence: mzheng@uwindsor.ca Received: 30 June 2024; Revised: 30 September 2024; Accepted: 10 October 2024; Published: 23 October 2024 Abstract: Modern compression ignition engines heavily rely on exhaust gas recirculation to reduce NOx emissions. Despite this, complex and expensive after-treatment systems are still necessary to comply with stringent emission regulations. Conventional diesel combustion operates on a robust and readily controllable mode through which the high-pressure fuel injection and combustion processes are intimately coupled. The heterogeneous nature of direct injection systems is liable to the NOx-soot trade-off inherent to diesel-fueled engines. Dimethyl ether (DME) presents a unique fuel that is reactive, volatile, and oxygenated, offering significant potential to address emission challenges with reduced reliance on aftertreatment systems. In this research, the combustion management of neat DME fuel was investigated using a high-pressure direct injection system. Principally, the suitability of single-shot fuel scheduling as a combustion management technique for DME under low NOx production was explored. The transient high-pressure injection behaviour of DME was characterized with an offline test bench. A single-cylinder research engine platform was employed to study DME combustion characteristics. A wide range of engine conditions was investigated, including injection pressures from 200 bar up to 880 bar and engine loads from 1 bar up to 17 bar indicated mean effective pressure (IMEP). The combustion management of DME as it relates to fuel injection and operating boundary conditions was emphasized throughout the work. To accomplish this, tests were conducted at direct comparison conditions to diesel operation. Most notably, the DME combustion process finished in a shorter period than diesel, albeit with a significantly longer injection duration. At most operating conditions, the soot emissions were below that of upcoming emission regulations without particulate filter exhaust treatment. Even under high engine load operation—17 bar IMEP—of neat DME, the NOx emissions could be readily contained via EGR management to 51 ppm engine-out NOx during which soot reached a maximum of 1.0 FSN. Such operating circumstances of high engine load and low oxygen availability (overall lambda of 1.2) exhibited a deterministic combustion timing control via injection timing while performing with low combustion noise (4.8 bar/°CA) and high burning efficiency (98.5%). The heavy-duty transportation sector is largely powered by internal combustion engines (ICEs) owing to their range of power density capabilities, reliability, and convenient handling of liquid fuel as the sole energy source. Compression ignition engines are valuable for such applications because of their inherent high thermal efficiency compared to their spark ignition counterparts. Through the advancements in technologies such as lightweighting, engine downsizing, aftertreatment materials, and combustion management, modern engines have reduced their tailpipe emissions footprint significantly concerning greenhouse gases, e.g., carbon dioxide (CO2), and harmful combustion byproducts, e.g., nitrogen oxides (NOx) and soot [1]. Still, it is predicted that the theoretical maximums of efficiency improvement and emission reduction are yet to be achieved, by way of further development in the fueling and combustion management area [2–4]. To ensure standardized progress toward reducing combustion byproducts, a set of tailpipe restrictions have been enacted in different regions throughout the globe, as noted in Table 1. A significant amount of effort has been focused on engine management strategies to meet emission regulation standards. Such regulations set limits on the maximum output of specified species at the tailpipe of on-road vehicles, including CO2, unburned hydrocarbon (UHC), carbon monoxide (CO), NOx, and soot. While the CO2 is predicated by the carbon content of the fuel and thermal efficiency, wherein a higher thermal efficiency will contribute to lowering the CO2 output, the remaining species are undesired combustion byproducts. The presence of UHC and CO in the exhaust indicates worsened combustion efficiency, whereas NOx and soot in due course harm the environment and human health. Emission regulations have become stricter over time, with current emission regulations over 90% lower than those introduced 20 years prior [5]. To this end, many improvements have been made successfully by the aftertreatment technology and combustion management, i.e., electronic engine control, electronic sensors, and active fuel and air handling systems [6]. 270 (2007) 47 (2027) 400 (2013) 200 (2027) 400 (2021) Present emission limits for NOx and soot are expected to experience a further reduction up to 83% and 38% in upcoming planned regulations, respectively. The European Union (EU, EURO standards) and the United States of America (USA, EPA standards) advocate distinctive regulation standards, ultimately aimed at similar range of reductions in exhaust emissions. Generally, most countries enact tailpipe emission limits similar to the EU standards in later years for heavy-duty vehicles, albeit with differing testing procedures [7,8]. Modern aftertreatment systems may exceed 90% conversion efficiency with proper operation and maintenance, allowing vehicles to conform to these tight emission regulations [9,10]. For illustrative purposes, an effective emissions target for engine research remains in the range of 10 to 20 times higher than the regulated tailpipe regulations, as shown in Table 2. In example, at a presumed 90% NOx conversion efficiency, the tailpipe regulations in the USA of 270 mg/kWh, and planned to become 47 mg/kWh, correspond to engine-out emission limits of 2700 mg/kWh and 470 mg/kWh, respectively. While further improvements in aftertreatment technology are plausible [11], additional emission reductions are expected to be realized through in-cylinder combustion management. Nonetheless, all regulations require a simultaneous reduction of NOx and soot emissions. This in practice, is an increasingly challenging task for compression ignition combustion systems. Conventional diesel combustion is a robust and readily controlled combustion mode through which the high-pressure fuel injection and combustion processes are intimately coupled near the top dead centre, as shown in Figure 1. This period of interest is comprised of an extremely rapid sequence of events that is often completed within a few milliseconds. Within this brief time frame, high-pressure fuel is injected, chemical reactions occur, fuel energy is released and emission products are formed, leading to a spatially and temporally complex system [12]. As the fuel injection and combustion are distinct, yet inherently connected processes, it is often the case that the fuel spray duration continues through the combustion event leading to a diffusion flame [13]. Figure 1. Overview of conventional diesel control and combustion behaviour. High-temperature diesel combustion as shown here is known for high efficiency but is prone to generate high levels of NOx emissions and, under high load conditions, soot. Substantial reductions in engine-out NOx emissions for compression ignition engines can be readily achieved through exhaust gas recirculation (EGR) [14]. However, a simultaneous increase in soot because of lower oxygen availability and lower combustion temperatures is often an unintended consequence of NOx mitigation efforts through EGR [15]. In general, lower oxygen availability at the start of combustion predictably lowers NOx emissions, whereas higher oxygen availability towards the end of combustion lowers soot emissions. Many operating boundary conditions act as suitable means of manipulating the physical and chemical influences to manage combustion, such as injection pressure, fuel scheduling, intake boost pressure, combustion phasing, and more. Nonetheless, the simultaneous balance of NOx and soot continues to prove challenging as the inevitable NOx-soot trade-off inherent to diesel-fueled engines persists [16,17]. The diffusion flame is a prominent phenomenon in compression ignition combustion as it facilitates a large portion of heat release under elevated engine loads [13]. It is often characterized by its mixing-controlled combustion features [18]. The close coupling of fuel injection and combustion amplifies the influence of the fuel properties on the subsequent combustion behaviour. A diffusion flame is generally undesired for enabling high NOx and soot emissions. In stark contrast, the diffusion flame provides a high-efficiency burning mode that is readily controlled in timing and intensity. As it is the undesired rise in soot emissions that limits the amount of EGR, the elimination of soot formation via fuel properties allocates a direct in-cylinder NOx management via EGR, reducing fuel scheduling and combustion management complexities. Fuel properties such as reactivity, fuel-borne oxygen content, and volatility have been proven advantageous for direct injection combustion applications for high efficiency and low engine-out soot emissions. A list of conventional and alternative fuels has been organized into three characteristics in Figure 2. A chemically reactive fuel, i.e., recognized by its adequate cetane number, enables high controllability and combustion completeness, tending to produce lower combustion noise [19]. On the other hand, fuels with high cetane numbers promote a greater degree of diffusion combustion and, in turn, may augment soot emissions [20]. An oxygenated fuel alleviates the dependency on oxygen availability from the cylinder charge during fuel spray and improves combustion completeness. Kitamura et al. [21] found that soot formation within the high-pressure fuel spray flame could be significantly reduced at >30% oxygen content. Lastly, volatility primarily enhances the atomization rate of fuel and air. Even though a volatile fuel may be subject to difficulties in liquid-phase high-pressure fuel injection, its application significantly influences the fuel spray and subsequent combustion event [22]. The period from fuel spray to autoignition involves both physical and chemical delays, wherein the physical delay dominates [23]. In high-pressure fuel sprays, Konno et al. [24] showed that the mixing quality of dimethyl ether (DME) at 600 bar injection pressure was equivalent to that of diesel at 2000 bar at half the nozzle orifice diameter. Teng and McCandless [25] explained that the rapid fuel evaporation was most notable around the perimeter of spray plume, effectively showing a turbulent-jet-like nature. Such behaviour may be most valuable during the diffusion flame when the rate of reaction is governed by the mixing rate. A faster diffusion combustion rate correspondingly improves controllability and enables a high efficiency, ultra-low emissions mode of combustion [26]. Through this comparison, the unique value of DME is apparent; a fuel possesses unique qualities of reactivity, volatility, and oxygen content. Figure 2. Qualities of conventional and alternative fuel. The potential of DME as a fuel for compression ignition engines has been widely investigated in academia and industry. The advantageous near-zero soot tendency of DME is clear, alongside the availability to be produced from a multitude of renewable feedstocks, presenting DME as an ideal fuel and sustainable energy source for future heavy-duty powertrains [27,28]. Apart from the engineering challenges associated with handling onboard high-pressure liquified DME, the engine performance is largely similar to that of diesel but with little inheritance NOx-soot trade-off [29–32]. In this respect, it is valuable to understand the combustion behaviour, akin to the research and development of diesel engines [33]. While engine performance appears similar, the unique fuel properties of DME necessitate adjustments in combustion management strategies. The fuel scheduling necessitates adjustments as the lower energy density raises the injection quantity ~55% by mass. With conventional single-shot fueling strategies, the injection duration will be extended significantly, especially as the physical properties of DME permit lower injection pressures. On the other hand, the extreme mitigation of soot emissions with DME can be leveraged for better control through prioritizing the diffusion combustion mode. In this work, the injection and combustion characteristics of neat DME fuel are investigated in a high-pressure direct injection combustion application. This research aims to compile and extend the understanding of DME combustion in a conventional direct injection combustion application The transient fuel injection and combustion processes are investigated with an offline test bench and online research engine platform, covering injection pressures from 200 bar up to 880 bar and engine loads from 1 bar up to 17 bar indicated mean effective pressure (IMEP). The combustion management of DME as it relates to fuel injection and operating boundary conditions is emphasized throughout the work. To accomplish this, tests were conducted at direct comparison conditions to diesel operation. For diesel engine tests, a higher fuel pressure of up to 1500 bar was applied to constructively match the lower volatility of diesel. The discussion primarily emphasizes comparative results to diesel fuel which acts as a reference for modern-day combustion management strategies. This comparison provides insight into the suitability of single-shot fuel scheduling as a combustion management technique for DME under low NOx emissions. The heterogeneous nature of direct injection combustion involves an intimate coupling of fuel delivering process and the combustion process. In this study, the management of DME fuel injection and combustion was investigated in a single-shot strategy. Diesel fuel was also investigated at matching conditions for relevance. An offline rate of injection measurement bench was used to study the injection characteristics of the fuels and the combustion characteristics were investigated on a single cylinder research engine. The fueling system was configured to adapt on-board and off-board high-pressure fueling systems suitable for diesel and DME fuels, respectively. This setup has enabled high-pressure direct injection and combustion studies with alternative fuels including those of low viscosity, high vapour pressure, and inadequate elastomer compatibility. Due to the predominance of diffusion combustion control, effective combustion control requires fast and precise instrumentation that can be readily adjusted. The unique physical fuel properties of DME compared with diesel fuel raise concern about the fuel injection behaviour regarding the real transient discharge process and the subsequent plume formation. In this section, the system specifications and testing procedure will be discussed. The Bosch long-tube method was utilized to analyze the injection rate profile for DME fuel. The results were then compared to those of diesel injection under the same conditions. The rate of injection measurement platform included a high-pressure injection pump, an injector installed in a reservoir connected to a 50-meter-long tube, and a host computer for monitoring, control, and data acquisition. An overview of the rate of injection platform is illustrated in Figure 3. The signals transmitted and received during testing were managed by an RT-FPGA system interfaced with the host computer, all orchestrated through the National Instruments LabVIEW software environment. Figure 3. Rate of injection research platform. The fuel properties of DME prevent its direct substitution for diesel fuel using traditional diesel injection systems due to DME’s higher vapour pressure, lower viscosity and lubricity, and its corrosive effects on elastomers. A list of selected fuel properties is given in Table 3. To address these challenges, a pneumatically driven double-air drive piston pump (Maximator LSF100-2) was used to supply high-pressure DME. This system accommodates a variety of alternative fuels regardless of physical properties, as the plunger was pneumatically driven and the sealing materials are chemically resistant. Liquid DME was fed from the bottom of a 1-gallon stainless steel tank, with the DME pressure maintained at approximately 20 bar absolute using a nitrogen supply at the top of the tank. Throughout the tests, a back-pressure range of 30~50 bar yielded the best results without noticeable differences. A stainless-steel chamber was designed and fabricated to hold a conventional diesel injector (8 × 140 µm). The pressure transducer was flush-mounted on the side of the chamber. Signals were sent to a piezoelectric injector driver to send the tuned opening and closing power signals to the injector. The pressure inside the chamber increased as the fuel was injected into the chamber. The corresponding rate of injection shape is proportional to the magnitude of pressure change recorded by the pressure transducer. The theoretical calculation from the measured chamber pressure mass flow rate is proportional to the total nozzle hole area and inversely proportional to the local speed of sound for the respective fluid [34]. Hydraulic delays can be categorized into opening and closing delays. More detailed information about the offline testing methodology can be found in [35]. The start of fuel delivery is considered reliable and has been validated with high-speed video recordings. The end of fuel delivery required assumptions in data processing. In this work, the raw signal exhibits an exponential delay as the ROI decreases at the end of fuel delivery. It is assumed that the needle effectively cuts off the fuel upon closing. Consequently, the end of the fuel delivery slope was extended using a linear fit line. The system was validated by recording an extended period and observing the pressure wave reflections. The reflected frequencies for diesel and DME resulted in estimated speeds of sound of 1389 m/s and 980 m/s, respectively. Similar speeds of sound for DME have been confirmed by Kapus and Ofner [13], as well as other studies [14–16]. The agreement between the speed of sound measurements in this study and those reported in the literature instills confidence in the results obtained from the long tube system. The engine is configured for direct injection CI research with an independent fuel injection system. A summary of engine geometry specifications is given in Table 4. An overview of the complete engine system is shown in Figure 4. All data acquisition and engine control programs are designed within the National Instruments LabVIEW software environment. The raw pressure data and fuel scheduling programs were programmed into the real-time operating systems on embedded NI controllers. A piezoelectric pressure transducer was flush-mounted to the cylinder head. The pressure measurements are synced with the optical encoder at a frequency of 7200 points per cycle, or every 0.1 °CA. Each operating condition logged a continuous 200 cycles of pressure recordings. Thermocouples and pressure sensors are...


  • Study of Dimethyl Ether Fuel Spray Characteristics and Injection Profile

    by Binghao Cong, Simon Leblanc, Xiao Yu, Ming Zheng

    The majority of transportation systems have continued to be powered by the internal combustion engine and fossil fuels. Heavy-duty applications especially are reliant on diesel engines for their high brake efficiency, power density, and robustness. Although engineering developments have advanced engines towards significantly fewer emissions and higher efficiency, the use of fossil-derived diesel as fuel sets a fundamental threshold in the achievable total net carbon reduction. Dimethyl ether can be produced from various renewable feedstocks and has a high chemical reactivity making it suitable for heavy-duty applications, namely compression ignition direct injection engines. Literature shows the successful use of DME fuels in diesel engines without significant hardware modifications. The lower energy density of DME calls for adjustments in injection parameters (such as injection pressure and duration) or modifications to the injector geometry to align with the energy levels found in diesel fuels. However, detailed direct comparisons between diesel and DME fuel injection characteristics over a wide testing range is lacking.This study investigates the injection characteristics of DME and diesel fuels in a common rail fuel injection system using the Bosch tube method. It is demonstrated that this method can be effectively applied to measure DME fuel injection characteristics, albeit with some limitations in predicting injector closing delay. The research emphasizes the presence of hydraulic delay, resulting in a ratio of actual to commanded injection duration for DME between 1.5 to 2 under the testing conditions. The study finds that mass-based injection quantities for diesel and DME fuels are quite similar at matching conditions, although the lower heating value of DME results in lower energy-based injection quantities and thus fuel injection scheduling need to be adapted to compensate that. Furthermore, the paper offers valuable insights and suggestions for those considering the modification of diesel-operated engines into DME-operated engines.


  • Open Access

    Advances and Challenges in Combustion Control of Radio Frequency Oscillating Plasma Discharge

    by Linyan Wang, Xiao Yu, Graham Reader, Ming Zheng

    Article Linyan Wang , Xiao Yu , Graham Reader , and Ming Zheng * Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, N9B 3P4 Ontario, Canada * Correspondence: mzheng@uwindsor.ca Received: 18 July 2023 Accepted: 13 September 2023 Published: 20 September 2023 Abstract: Oscillating plasma (corona) ignition is a promising technique for producing a larger initial ignition volume for achieving cleaner combustion. The oscillating plasma system provides a quick response to the ignition command compared with the conventional transistor-coil-ignition systems (TCI). Subsequently, the shorter combustion duration contributes to further improvement of engine efficiency under lean/diluted conditions. The challenges of oscillating plasma ignition appear under elevated background pressures, mostly owing to fewer plasma streamers and even void discharge, thus the advantage of oscillating plasma discharge over spark discharge is compromised. To suffice the industrial applications, the challenges of plasma generation and control platforms are investigated and discussed in this work. The challenges include ignition control, background condition impacts, and other external disturbances. A flexible modulation for oscillating plasma generation is established, with the measurements of discharge voltage and current. High-speed imaging, simultaneous with electrical waveform measurements is applied to record the plasma formation and flame propagation. This research provides advances in the ignition control for the oscillating plasma discharge, adding a foundation and reference for the oscillating plasma diagnostics under engine-like conditions with variations of pressure, temperature, gas composition, and flow pattern. The internal combustion (IC) engine has been the primary power source for automotive applications, and will continuously power the majority of automotive vehicles including hybrids, in the foreseeable future [1‒4]. The greenhouse gas (GHG) emission challenge can only be met optimally with an appropriate technology mix, such as electrical energy, hydrogen or E-fuels, and renewable fuels, adapted to each respective application [5]. To achieve such high efficiencies, lean-burn and exhaust gas recirculation (EGR) diluted combustion technologies need to be adopted to reduce pumping loss under partial load, mitigate knocking events to achieve preferable combustion phasing under high engine load, and reduce heat transfer loss because of the low-temperature combustion [6]. However, ignition difficulty and slow flame propagation speed become the major challenges because of the much lower chemical reactivity of the air-fuel mixtures [7,8]. In this context, advanced ignition technologies based on non-equilibrium plasma discharge become important because they show great potential in combustion, emission control as well as fuel reforming [9]. Radio frequency (RF) oscillating plasma (Corona), dielectric barrier discharge, nanosecond discharge, gliding arc, and microwave have higher electron temperatures [10], and they are more kinetically active owing to the rapid production of active radicals and excited species via electron impact dissociation, excitation, and subsequent energy relaxation [11,‍12]. The enhancement of ignition using non-equilibrium plasma can be achieved in three aspects. First, the branched plasma streamers have the potential to increase the size of the flame kernel and ignition volume [13]. Second, the high electron energy of the non-equilibrium plasma promotes ion chemistry and generates active radicals and small molecule fuel fragments [9], which has benefits on the ignition process. The residence time of OH is typically below 100 μs, as observed in the nanosecond non-equilibrium plasma ignition experiments conducted by Wu [14], and repetitive discharge is often used for nanosecond pulsed non-equilibrium plasma ignition [15]. In comparison, the RF oscillating plasma ignition can continuously produce non-equilibrium plasma in milliseconds duration to compensate for the decay of previously formed radicals until the success of ignition [16]. Third, as the effect of an electric field on flame propagation has been extensively reported in the past, post-ignition flame propagation can be accelerated due to the ionic wind effect near the ignitor [17]. Oscillating plasma discharge shows promises for the stable and successful ignition of lean and diluted mixtures. As shown in Figure 1, without the ground electrode, the streamers released from the plasma antenna can stretch beyond the size of the conventional spark gap and establish a much bigger ignition volume. The high frequency oscillating electric field generated at the tip of the antenna can force distortion on the flame front. The enhancement of the burning rate and acceleration of the flame kernel growth is contributed by the flame front wrinkles in the shadowgraph image [18]. Figure 1. Plasma and conventional spark discharge and relevant flame kernel formation in shadowgraph images (adapted with permission from Yu et al. [19]). Under engine conditions, the shorter combustion duration contributes to further improvement of engine efficiency under lean/diluted conditions. The oscillating plasma system provides a quick response to the ignition command in microsecond order, compared with millisecond order for a conventional transistor-coil-ignition system (TCI). The system can also continuously deliver ignition energy according to engine demands [10]. Another unique feature of the RF plasma ignition technology is that the combustion chamber, with the working fluid forming a virtual capacitor, is a part of the resonant electrical circuit. This allows potential diagnosis of the flame kernel growth process using the ignition hardware. It is also possible and advantageous to implement electrification near the ignitor to accelerate the flame kernel. However, as the ground electrode is absent from the plasma antenna, the plasma ignition is susceptible to the surrounding conditions, because the dielectric medium around the plasma antenna becomes a part of the electrical circuit during energy release. An illustrative structural scheme of a basic plasma ignition system is shown in Figure 2. Under engine conditions, the rapid change of in-cylinder pressure and temperature produces a complicated background condition, which challenges a stable plasma discharge [20,21]. At the top dead center (TDC) of engine operation, the distance between the plasma and the surface of the piston is greatly shortened, which can trigger unwanted arc discharge [22,23]. Contamination of the plasma antenna and its ceramic insulator can lead to surface discharge or direct arc to the metal shell of the plasma igniter [23‒25]. Therefore, to ensure robust and reliable plasma discharge, it is essential to understand the discharge mechanism and operational boundaries of the oscillating plasma discharge process [18]. Furthermore, in order to suffice the industrial applications, it is valuable and necessary to discuss the challenges existing in plasma generation and control platforms. Figure 2. Basic structural scheme of an oscillating plasma ignition system. In this work, an advanced oscillating plasma discharge control system is proposed, with the discharge process characterized by electrical waveform measurements of the voltage and current. Subsequently, the challenges of plasma discharge under engine-like conditions are discussed in detail. Elevated background pressure can significantly affect the RF oscillating plasma discharge, in terms of fewer streamer numbers and smaller size, which will compromise its advantage over a spark event. The electrical waveforms with the simultaneous high-speed imaging of the visualized plasma streamers and flame propagation present a deeper understanding of the oscillating plasma discharge and ignition. This research adds references for plasma ignition and diagnostics under engine-like conditions with variations in pressure, temperature, gas composition, and flow pattern. An in-house built RF oscillating plasma discharge control system has been used to generate oscillating plasma discharge with adjustable discharge frequency, voltage, and duration [16,22]. The system consists of a single-electrode igniter, a resonator coil, an RF transformer, and power drive electronics. The high-frequency (800 kHz‒2.6 MHz) pulse train is generated by a function generator (Agilent 33220A) and should be consistent with the RLC electrical resonance frequency of the ignition system to achieve the highest discharge voltage at the tip of the ignitor. The control command (for discharge duration and frequency control) is generated via an RT-FPGA, i.e., real-time field-programmable gate array. The voltage supply on the primary side is kept consistent in this paper as 60 V. The discharge current and voltage are measured with a Pearson 411 current probe and Tektronix P6015 high voltage probe, respectively. The simplified diagram of the in-house built RF oscillating plasma control system and the electrical waveforms using the logarithmic scale are presented in Figure 3 [16]. Figure 3. Experimental circuit and electrical waveforms of the oscillating plasma ignition system [16]. As shown in Figure 2, a typical plasma discharge system consists of a direct current (DC) power supply, a power drive, and a plasma antenna. A pulsed-train command with a favorable oscillating frequency is applied to stimulate the plasma power drive, aiming to generate a high voltage at the plasma antenna. Unlike conventional spark plugs utilizing a ground electrode to guide the direction of the plasma channel, the plasma ignition system releases the plasma streamers by ionizing the gaseous media around the antenna [26]. The ionized surrounding media becomes a part of the discharging circuit, and plasma discharge is thus affected by the changes in background conditions [27,28]. Figure 4 lists potential factors that may affect the plasma discharge. These factors include ignition control, background conditions, and external disturbances. Figure 4. Impacts on oscillating plasma discharge under engine-like conditions. 3.1. Challenges of Ignition Control The oscillating frequency of the power drive can be adjusted by a pulse train command. However, the oscillating frequency needs to match the optimal working frequency of a system (resistor-inductor-capacitor (RLC) electrical resonance frequency) for plasma discharge. The optimal working frequency is determined by the hardware setup [29]. Figure 5 shows waveforms of discharge voltage and current with the impact of oscillating frequency on energy and discharge voltage. Figure 5. Voltage and current measurements in the time domain (a), discharge energy, and peak voltage in the frequency domain (b) (adapted with permission from Yu et al. [19]). Under the time domain, during the plasma oscillation, the amplitudes of discharge voltage and current waveforms increase initially until reaching the peak values. In order to sustain the plasma discharge, the amplitudes decrease and stabilize subsequently. As shown in Figure 5b, the oscillating frequency needs to be modulated within a narrow bandwidth (~0.03 MHz) to generate sufficient discharge voltage to establish a plasma discharge. Discharging bandwidth is affected by background conditions and disturbances. Under engine conditions, elevated cylinder pressure can suppress the plasma discharge event, and the discharging bandwidth is narrowed consequently [24]. Thus, the strict requirements of oscillating frequency modulation demand control systems with high accuracy and fast response. The peak discharge voltage is determined by the DC power supply voltage, which needs to be controlled within a strict range to establish plasma discharge. For instance, under the experimental setup in this work, the DC power supply voltage lower than 30 V is not sufficient to generate plasma discharge; however, a supply voltage higher than 80V will trigger an unwanted arc discharge. Since plasma discharge relies on the initial ionization of the gas media in the vicinity of the plasma antenna, the electric field gradient is thus an important parameter affecting the plasma discharge event [24,28]. Under similar discharge voltage, the electric field gradient is influenced by the geometry of the antenna tip. Empirical results indicate that the plasma is easy to discharge from the antenna with a sharper tip. The wear and erosion of the antenna will degrade the electric field gradient, leading to void discharge even under the same discharge voltage. 3.2. Impacts of Background Conditions The direct images in Figure 6 show the oscillating plasma discharge in Nitrogen under various background pressures [16]. Theoretically, the oscillating plasma discharge under vacuum conditions tends to generate relatively homogeneous plasma. It can be observed that a diffusive plasma discharge exists under 0.1 bar absolute pressure, but transits to streamer discharge under 1 bar. Under higher background pressure, the mean free path of the particles is decreased, and the collision frequency increases. The plasma streamer length is shortened from approximately 22 mm to 2 mm, as the background pressure further increases from 1 bar to 5 bar. Thus, the advantage of oscillating plasma discharge over spark discharge is compromised under higher background pressure. Figure 6. Oscillating plasma discharge under elevated pressure conditions [16]. Figure 7 demonstrates the background pressure impact on the oscillating plasma discharge and flame kernel formation. Overall, compared with the conventional spark ignition shown in Figure 1, the plasma discharge can generate a bigger initial flame kernel with more wrinkles at the flame front. It is noticed that under elevated background pressure, both the size and number of the streamers decrease, resulting in a smaller initial flame kernel. The elevated pressure results in the volume shrinkage of the initial flame kernel area. However, small but dense flame kernels are formed along the streamers, which further contribute to the dense flame front wrinkles and more intensified successful ignition sites. Figure 7. Shadowgraph imaging of flame kernel development initiated by oscillating plasma under a pressurized mixture. The background gas composition and pressure often lead to different ionization coefficients, attachment coefficients, and the mobility status of the space charges [30,‍31]. Thus, it is important to investigate the influence of background gas ionization and pressure on the plasma discharge. A higher background temperature enhances the kinetic energy of the air molecules, which benefits the plasma discharge. The minimum voltage required for plasma discharge decreases with the increase in the background temperature [32]. The impact of the flow pattern on plasma discharge is less understood, but preliminary research in the authors’ work suggests a marginal impact of flow speed on plasma discharge. Considering the plasma discharge with an oscillating frequency of approximately 2 MHz, the building-up process is normally within microseconds. With cross flow speed of 30 m/s, which is considered a high in-cylinder flow motion, the moving distance within each oscillation cycle is around tens of micrometers. Because the size of normal plasma discharge is around 5–10 mm even under elevated background pressure conditions, the air movement is negligible. 3.3. Impacts of Other External Disturbances Because of the absence of the ground electrode, the distribution of the electric field close to the antenna tip can be easily distorted by external disturbances. A touchdown of the plasma streamers to the ground is recognized as an arc discharge. The approach of a piston during spark event near engine compression TDC, or combustion chamber geometry can significantly increase the arcing tendency. Once the unwanted arc discharge takes place, the electric field around it changes rapidly and collapses, and a strong current surge can be noticed on the discharge waveform. The current surge during the arc discharge can generate heat, hence accelerating the wear of the antenna tip [23]. The discharge voltage waveforms of three typical oscillating plasma discharge events are plotted in Figure 8 including the void discharge, established discharge, and arc discharge. Figure 8. The comparison of the measured discharge voltage of void, established, and arc discharge events (adapted with permission from Wang et al. [22]). The black dash lines shown in Figure 8 indicate the amplitude of the voltage waveforms. When the command pulse train is sent to the plasma power drive, the oscillation begins in the plasma ignition system. The discharge voltage keeps increasing until it reaches the peak value. When the plasma fails to release from the antenna, the voltage amplitude stays relatively stable throughout the commanded duration. However, with established plasma discharge, the waveform envelopes decline slightly and stabilize until the command ends. In an arc discharge event, when the plasma streamers touch down to a metal surface, the discharge voltage drops immediately from 6 kV to 2 kV. Carbon deposits generated by incomplete combustion and unburned fuel droplets can attach to the surface of the ceramic insulator. The degraded insulation leads to surface discharge and arc discharge, which will compromise the ignition capability of the plasma streamers. Therefore, a stable plasma discharge under engine conditions remains to be a challenge. Control models and strategies that can predict normal and abnormal discharging events based on discharge waveforms will enable the dynamic control of the plasma system. Therefore, plasma discharge characteristics need to be further investigated via electrical waveform measurements and analysis. This study investigates and discusses the advances and challenges of oscillating plasma discharge for clean combustion and industrial applications. The major conclusions are: Author Contributions: Conceptualization, M.Z., X.Y. and G.R.; Methodology, X.Y. and L.W.; Software, L.W.; Validation, L.W.; Formal analysis, L.W. and X.Y.; Investigation, L.W.; Resources, L.W.; data curation, L.W. and X.Y.; Writing—Original draft preparation, L.W. and G.R.; Writing—review and editing, L.W.; Visualization, G.R.; supervision, X.Y., M.Z., and G.R.; Project administration, M.Z.; Funding acquisition, M.Z. All authors have read and agreed to the published version of the manuscript. Funding: This research received no external funding Acknowledgments: The research at the Clean Combustion Engine Laboratory is partially sponsored by: NSERC/IRC, NSERC/CRD, NSERC/RTI, NSERC/DG, CFI/ORF, and the University of Windsor. Special thanks to Torch and other OEMs for their technical support, and CCEL colleagues’ contribution in their time. Conflicts of Interest: The authors declare no conflict of interest.


  • Open Access

    Dimethyl Ether to Power Next-Generation Road Transportation

    by Simon LeBlanc, Xiao Yu, Linyan Wang, Ming Zheng

    Review Dimethyl Ether to Power Next-Generation Road Transportation Simon LeBlanc , Xiao Yu , Linyan Wang , and Ming Zheng , * Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, N9B 3P4 Ontario, Canada * Correspondence: mzheng@uwindsor.ca Received: 20 March 2023 Accepted: 8 June 2023 Published: 19 June 2023 The prevailing transportation uses internal combustion engines powered by fossil fuels that bear the reputation of carbon dioxide release among other harmful emissions. As an alternative, dimethyl ether (DME) has shown a high potential to mitigate emission challenges. The properties of DME present a highly reactive and volatile fuel suitable for clean combustion. However, the onboard handling of liquified DME is an ongoing challenge, especially for high-pressure direct injection applications. This paper aims to evaluate the sustainability, fuel handling, and combustion characteristics of DME as a clean and efficient fuel for sustainable on-road transportation. Strategies toward integrating DME fuel for automotive applications are emphasized. An overview of DME production is provided with relevance to current industry practices. Thereafter, the chemical and physical properties of DME are highlighted. The handling challenges of DME are accentuated, and accordingly, recommendations are made for setting up fuel management systems applicable to on-road engines and research laboratories. The DME fueling configurations, e.g., port injection and direct injection, are summarized. Empirical tests studied the engine and emission performance of DME combustion. Ultra-low NOx and smoke emissions, with high combustion efficiency, are achieved.


  • Open Access

    Spark Plasma Stretching and Ignition Improvement via High Frequency Pulsed Current Boost

    by Linyan Wang, Xiao Yu, Zhi Yang Ong, Simon LeBlanc, Ming Zheng

    Article Spark Plasma Stretching and Ignition Improvement via High Frequency Pulsed Current Boost Linyan Wang , Xiao Yu , Zhi Yang Ong , Simon LeBlanc , and Ming Zheng ,* Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, N9B 3P4 Ontario, Canada * Correspondence: mzheng@uwindsor.ca Received: 9 May 2023 Accepted: 12 May 2023 Published: 19 June 2023 In modern engines, the improvement of fuel efficiency and reduction of exhaust emissions have become increasingly important, with the consequent need for improved performance and advancement of ignition systems. The ignition mechanisms utilized in modern engines frequently encounter a fuel-lean or gas-diluted blend of substantial density and vigorous airflow. Under such conditions, the spark plasma is influenced by gas movements, specifically crossflows that occur in a voluminous manner. The gas motions can stretch the plasma channel, thereby amplifying the total discharge energy compared to quiescent conditions. It has been proven that an increased discharge current is an efficacious method for extending the duration of spark plasma stretching. Nevertheless, high discharge current can increase the energy consumption of ignition systems and consequently, influence the durability and overall energy efficiency of the system. Moreover, the persistent flow of intense electrical current leads to prompt erosion of the spark electrode, impacting the durability of the spark plug. In this study, a novel ignition strategy of high-frequency pulsed currents is introduced, to enhance the effectiveness of plasma stretching and energy discharge while minimizing the overall energy usage of ignition systems. A high-frequency pulsed discharge strategy is accomplished within the controlled duration without affecting the plasma stretching phenomenon. The plasma channel behaviors are logged using electrical and optical measurements. Furthermore, the discharge frequency and current level impacts of the boosted current pulses on the plasma stretching behavior and flame propagation are also investigated.


  • Open Access

    Decarbonization potential of future sustainable propulsion—A review of road transportation

    by Xiao Yu, Simon LeBlanc, Navjot Sandhu, Linyan Wang, Meiping Wang, Ming Zheng

    Modern automotive propulsion technologies must achieve the highest CO2 reduction potential quickly to abide by the requirements of the Paris Climate Agreement. A collective utilization of renewable fuels, e‐fuels, hydrogen, and electrical energy will be able to meet different mobility and transport requirements in an optimal and CO2‐neutral approach. The well‐to‐wheel greenhouse gas emissions of a propulsion system are determined by two factors, that is, the energy efficiency of the system and the carbon intensity of the energy source. Regardless of the CO2 emission generated during the battery manufacturing and recycling process, the carbon intensity of the battery electric vehicles during operation is mainly decided by the carbon intensity of the electricity being consumed. The relatively low fleet ratios of battery electric and hydrogen‐powered vehicles and the massive remaining useful life of current internal combustion engine vehicle stock limit their impact on decarbonization in the near term. The expansion of charging infrastructure requires significant acceleration for the success of large‐scale and rapid electric vehicle adoption. For internal combustion engines, the focus is to further improve energy efficiency and the adoption of low‐to‐zero carbon renewable fuels. Hybrid and plug‐in hybrid vehicles are demonstrating the advantages of combining state‐of‐the‐art technologies to reduce both energy consumption and carbon emissions. In this review, the present status of propulsion systems is reviewed in detail, considering both the market penetration and well‐to‐wheel carbon emissions. The decarbonization potentials of various propulsion systems are then discussed.