Paula Camarena-Bononad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Paula Camarena-Bononad has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Amparo Chiralt
University Institute of Food Engineering—FoodUPV, Universitat Politècnica de València (UPV), Camino de Vera s/n, 46022 Valencia, Spain
2 shared publications - Maria Vargas
Instituto de Ingeniería de Alimentos-FoodUPV, Universitat Politècnica de València, 46022 Valencia, Spain
2 shared publications - Pedro Augusto Vieira de Freitas
Institute of Food Engineering FoodUPV, Universitat Politècnica de València, 46022 Valencia, Spain
2 shared publications - Chelo González-Martínez
Institute of Food Engineering-FoodUPV, Universitat Politècnica de València, 46022 Valencia, Spain
1 shared publication
Latest Publications
- Open Access
- 2 April 2025
- Published by MDPI AG in Polysaccharides
- Vol. 6 (2) , 27
Use of Cellulose Fibres from Posidonia oceanica to Obtain Chitosan Biocomposites and Poly(lactic Acid) Laminates
New sustainable materials have been developed to replace conventional plastics obtained from non-renewable sources. In this study, cellulose fibres from Posidonia oceanica (PO) were obtained by applying subcritical water extraction and bleaching with hydrogen peroxide or sodium chlorite. The PO fibres were used to obtain cellulose films, chitosan–cellulose composites, and PLA–cellulose laminates. These films were characterised as to their optical properties, mechanical performance, oxygen and water vapour permeability, thermal stability, and microstructure. The cellulose films exhibited low mechanical resistance, with different colouration depending on the degree of delignification. The composites had lower mechanical strength than pure chitosan films. The PO cellulose fibres had a similar, but attenuated, effect when laminated with PLA layers. The fibres improved the oxygen barrier capacity of chitosan films, although this effect only occurred in PLA laminates for cellulose purified with sodium chlorite. In no case did cellulose improve the water vapour barrier of the films compared to pure polymers. The thermal stability was not notably altered by the blending effect, thus reflecting the absence of significant interactions between the fibres and polymer. However, there is a need to improve the functionality of cellulose fibres from PO waste for their incorporation as fillers or laminates in biodegradable food packaging materials.
- 2 April 2025
- Published by MDPI AG in Polysaccharides
- Vol. 6 (2) , 27
Open AccessUse of Cellulose Fibres from Posidonia oceanica to Obtain Chitosan Biocomposites and Poly(lactic Acid) Laminates
New sustainable materials have been developed to replace conventional plastics obtained from non-renewable sources. In this study, cellulose fibres from Posidonia oceanica (PO) were obtained by applying subcritical water extraction and bleaching with hydrogen peroxide or sodium chlorite. The PO fibres were used to obtain cellulose films, chitosan–cellulose composites, and PLA–cellulose laminates. These films were characterised as to their optical properties, mechanical performance, oxygen and water vapour permeability, thermal stability, and microstructure. The cellulose films exhibited low mechanical resistance, with different colouration depending on the degree of delignification. The composites had lower mechanical strength than pure chitosan films. The PO cellulose fibres had a similar, but attenuated, effect when laminated with PLA layers. The fibres improved the oxygen barrier capacity of chitosan films, although this effect only occurred in PLA laminates for cellulose purified with sodium chlorite. In no case did cellulose improve the water vapour barrier of the films compared to pure polymers. The thermal stability was not notably altered by the blending effect, thus reflecting the absence of significant interactions between the fibres and polymer. However, there is a need to improve the functionality of cellulose fibres from PO waste for their incorporation as fillers or laminates in biodegradable food packaging materials.
- Open Access
- 5 December 2024
- Published by MDPI AG in Polysaccharides
- Vol. 5 (4) , 807-822
Influence of the Purification Degree of Cellulose from Posidonia oceanica on the Properties of Cellulose-PLA Composites
PLA biocomposites, incorporating 5% wt. of lignocellulosic fibres (LF) from Posidonia oceanica waste with different degrees of cellulose purification, were obtained by melt blending and compression moulding. The LF were obtained after removing part of the non-cellulosic components by subcritical water extraction at 150 and 170 °C and after bleaching the extracted residues with hydrogen peroxide or sodium chlorite. The non-bleached LF provided the composites with a brown colour and opacity, while the bleached LF impacted the optical properties of composites to a lower extent, depending on their whiteness. The LF composition had a noticeable effect on the composites’ mechanical and barrier properties. All LF reduced the water vapour barrier capacity while promoting the oxygen barrier of the films. Bleached LF enhanced the film stiffness and reduced extensibility and resistance to break, whereas non-bleached LF had lower impacts on the tensile parameters. Considering the mechanical and barrier performance of the composites, the fibres obtained at 170 °C and bleached with sodium chlorite exhibited the best behaviour. Nevertheless, if transparency and colour are not limiting for the use of the films, untreated LF allowed for good preservation of the water vapour permeability of PLA films and enhanced the oxygen barrier capacity, with a similar mechanical response as the other non-bleached fractions.
- 5 December 2024
- Published by MDPI AG in Polysaccharides
- Vol. 5 (4) , 807-822
Open AccessInfluence of the Purification Degree of Cellulose from Posidonia oceanica on the Properties of Cellulose-PLA Composites
PLA biocomposites, incorporating 5% wt. of lignocellulosic fibres (LF) from Posidonia oceanica waste with different degrees of cellulose purification, were obtained by melt blending and compression moulding. The LF were obtained after removing part of the non-cellulosic components by subcritical water extraction at 150 and 170 °C and after bleaching the extracted residues with hydrogen peroxide or sodium chlorite. The non-bleached LF provided the composites with a brown colour and opacity, while the bleached LF impacted the optical properties of composites to a lower extent, depending on their whiteness. The LF composition had a noticeable effect on the composites’ mechanical and barrier properties. All LF reduced the water vapour barrier capacity while promoting the oxygen barrier of the films. Bleached LF enhanced the film stiffness and reduced extensibility and resistance to break, whereas non-bleached LF had lower impacts on the tensile parameters. Considering the mechanical and barrier performance of the composites, the fibres obtained at 170 °C and bleached with sodium chlorite exhibited the best behaviour. Nevertheless, if transparency and colour are not limiting for the use of the films, untreated LF allowed for good preservation of the water vapour permeability of PLA films and enhanced the oxygen barrier capacity, with a similar mechanical response as the other non-bleached fractions.