Pamala Samara Vieira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pamala Samara Vieira has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Anderson Costa Marques
Universidade Federal do Rio Grande do Norte, Brasil
2 shared publications Michelle Cequeira Feitor
2 shared publications- Thalita Q. Silva
Universidade Federal do Rio Grande do Norte, Brasil
2 shared publications - Allan Jedson Menezes Araujo
TEMA – Centre for Mechanical Technology and Automation, Department of Mechanical Engineering, University of Aveiro, 3810-193 Aveiro, Portugal
1 shared publication - Ana Biatriz Guedes Do Nascimento1 shared publication
Ana Sofia Figueira Ramos
1 shared publication
Latest Publications
- 12 November 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1087
Phase evolution and chemical heterogeneity in CuWMoTaV powders during high-energy ball milling
- 12 November 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1087
Phase evolution and chemical heterogeneity in CuWMoTaV powders during high-energy ball milling
- Open Access
- 5 October 2026
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 220
Effect of deposition temperature on the structural and compositional evolution of NiTi and NiTiCu thin films produced by cathodic cylinder plasma deposition
- 5 October 2026
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 220
Open AccessEffect of deposition temperature on the structural and compositional evolution of NiTi and NiTiCu thin films produced by cathodic cylinder plasma deposition
- Open Access
- 20 March 2026
- Published by Elsevier in Applied Surface Science
- Vol. 733
Unraveling OER kinetics in multicationic spinel oxides: Challenges and insights from Tafel slope analysis
- 20 March 2026
- Published by Elsevier in Applied Surface Science
- Vol. 733
Open AccessUnraveling OER kinetics in multicationic spinel oxides: Challenges and insights from Tafel slope analysis
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Analysis of Sintering Curves, Microstructure, and Microhardness of the Cu-WC Composite
Composite materials have gained prominence due to their tailored properties for various applications. Cu-WC composites, combining a copper matrix with tungsten carbide reinforcement, are particularly valuable for electrical conductors and heat sinks. This study examined the sintering behavior of Cu-WC composite powder (10%WC) produced via High-Energy Ball Milling (HEBM) at 400 RPM for 2, 10, and 20 hours. The powders were compacted at 150 MPa and sintered at 900°C with a 1-hour isothermal hold. Sintering curves, microstructure, and Vickers microhardness were analyzed. The results showed that longer milling times led to significant powder expansion up to 750°C, followed by greater shrinkage due to diffusion mechanisms. Sintered samples milled for 10 hours displayed improved carbide distribution in the copper matrix. The highest microhardness was achieved at 20 hours of milling, attributed to refined microstructure. Extended milling times enhanced atomic diffusion during sintering, resulting in a more homogeneous structure and increased hardness.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1)
Open AccessAnalysis of Sintering Curves, Microstructure, and Microhardness of the Cu-WC Composite
Composite materials have gained prominence due to their tailored properties for various applications. Cu-WC composites, combining a copper matrix with tungsten carbide reinforcement, are particularly valuable for electrical conductors and heat sinks. This study examined the sintering behavior of Cu-WC composite powder (10%WC) produced via High-Energy Ball Milling (HEBM) at 400 RPM for 2, 10, and 20 hours. The powders were compacted at 150 MPa and sintered at 900°C with a 1-hour isothermal hold. Sintering curves, microstructure, and Vickers microhardness were analyzed. The results showed that longer milling times led to significant powder expansion up to 750°C, followed by greater shrinkage due to diffusion mechanisms. Sintered samples milled for 10 hours displayed improved carbide distribution in the copper matrix. The highest microhardness was achieved at 20 hours of milling, attributed to refined microstructure. Extended milling times enhanced atomic diffusion during sintering, resulting in a more homogeneous structure and increased hardness.
- Open Access
- 4 December 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (50) , 49849-49856
Single-Step Deposition of Chalcopyrite (CuFeS2) Thin Films
Thin films of chalcopyrite, CuFeS2, are promising candidates for use as absorber layers in photovoltaic cells due to their low band gap and high absorbance. These films are typically deposited in two or three steps, always involving an annealing process. In this work, the CuFeS2 film was deposited on a glass substrate in a single deposition step using the cathodic cylindrical plasma deposition (CCyPD) technique. The film samples deposited were analyzed by X-ray diffraction (XRD) and Raman spectroscopy, the film thickness was measured using the optical method, and FEG-SEM analyzed the surface structural morphology. The results showed a strong dependence on the deposition temperature for phase formation, with chalcopyrite being obtained for films deposited at 600 °C. At this temperature, a uniformly distributed film with uniform grain sizes was obtained, and the experimentally obtained band gap values of the films were consistent with the theoretical values reported in the literature, demonstrating the technique's effectiveness and precision in producing high-quality films.
- 4 December 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (50) , 49849-49856
Open AccessSingle-Step Deposition of Chalcopyrite (CuFeS2) Thin Films
Thin films of chalcopyrite, CuFeS2, are promising candidates for use as absorber layers in photovoltaic cells due to their low band gap and high absorbance. These films are typically deposited in two or three steps, always involving an annealing process. In this work, the CuFeS2 film was deposited on a glass substrate in a single deposition step using the cathodic cylindrical plasma deposition (CCyPD) technique. The film samples deposited were analyzed by X-ray diffraction (XRD) and Raman spectroscopy, the film thickness was measured using the optical method, and FEG-SEM analyzed the surface structural morphology. The results showed a strong dependence on the deposition temperature for phase formation, with chalcopyrite being obtained for films deposited at 600 °C. At this temperature, a uniformly distributed film with uniform grain sizes was obtained, and the experimentally obtained band gap values of the films were consistent with the theoretical values reported in the literature, demonstrating the technique's effectiveness and precision in producing high-quality films.