Tetiana Rodymchenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tetiana Rodymchenko has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Serhiy Vanyeyev
Department of Technical Thermal Physics, Sumy State University, 116, Kharkivska St., 40007 Sumy, Ukraine
2 shared publications - Jana Mižáková
Faculty of Manufacturing Technologies with a seat in Presov, Technical University of Kosice, 080 01 Prešov, Slovakia
1 shared publication - Ján Piteľ
Technical University of Košice
1 shared publication - Michal Hatala
Technical University of Košice
1 shared publication - Natalia Lishchenko
Trinity College Dublin
1 shared publication O Bolotnikova
Sumy State University, Sumy, R-Korsakova str., 2, Ukraine, 40007
1 shared publication
Latest Publications
- 25 May 2022
- Published by Springer Nature
- p. 288-298
Jet-Reactive Turbine Circular Efficiency
- Open Access
Numerical Simulation of Gas Flow Passing through Slots of Various Shapes in Labyrinth Seals
Labyrinth seals are widely used in centrifugal compressors, turbines, and many other pneumatic systems due to their simplicity of design, reliability, and low cost. The calculation scheme for the movement of the working medium in a labyrinth seal is constructed by analogy with the movement of the working medium through holes with a sharp edge. Annular and flat slots, holes, and such a factor as the shaft rotation with a calculated sector of 3 degrees were studied. The purpose of the study is to determine the flow coefficient when the working medium flows through slots of various shapes. To achieve this purpose, modeling of the working medium flow in the FlowVision software was performed. The mass flow and flow coefficients are determined for the studied slot shapes. The convergence of the calculation results was determined by comparing the values of the mass flow rate at the inlet and outlet of the slot. Differences in visualizations of the flow for the studied variants of slots were established. The resulting difference should be taken into account in practical calculations of the working medium mass flow through the slot using a conditional flow rate factor which is determined by the slot design.
Open AccessNumerical Simulation of Gas Flow Passing through Slots of Various Shapes in Labyrinth Seals
Labyrinth seals are widely used in centrifugal compressors, turbines, and many other pneumatic systems due to their simplicity of design, reliability, and low cost. The calculation scheme for the movement of the working medium in a labyrinth seal is constructed by analogy with the movement of the working medium through holes with a sharp edge. Annular and flat slots, holes, and such a factor as the shaft rotation with a calculated sector of 3 degrees were studied. The purpose of the study is to determine the flow coefficient when the working medium flows through slots of various shapes. To achieve this purpose, modeling of the working medium flow in the FlowVision software was performed. The mass flow and flow coefficients are determined for the studied slot shapes. The convergence of the calculation results was determined by comparing the values of the mass flow rate at the inlet and outlet of the slot. Differences in visualizations of the flow for the studied variants of slots were established. The resulting difference should be taken into account in practical calculations of the working medium mass flow through the slot using a conditional flow rate factor which is determined by the slot design.
- Open Access
- 1 January 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1741 (1) , 012004
Influence of the degree of off-design of the traction nozzle of a jet reaction turbine on its efficiency
At the present stage of social development, the need for rational use of energy resources of the planet is particularly acute. Most countries have already faced the problem of the energy crisis. An appropriate way to solve this problem is the utilization of secondary energy resources. With the help of turbine generators, it is possible to reduce the pressure and utilize the potential energy of excess pressure of gas or vapours to produce electricity. Such units can be created based on a jet reaction turbine. The study aims to assess the impact of the degree of off-design of the traction nozzle on the efficiency of the jet reactive turbine. The analysis of the factors influencing the efficiency of the jet reaction turbine is carried out in the work. The obtained efficiency rate for the jet reactive turbine depending on the given dimensionless velocity of λout t at the inlet pressure of the inlet nozzle of 2, 4, 6 and 10 MPa in the design mode (at the degree of off-design of S = 1) and in the off-design modes of operation ( S> 1). Graphical dependencies of the jet reaction turbine efficiency rate on the given circular velocity of the impeller are constructed (U− = 0… 0.7). The research shows that with increasing pressure at the inlet to the inlet nozzle, the efficiency rate of the turbine increases, and the optimum of the efficiency rate is shifted towards the increase of the given circular velocity of the impeller, both in the design and off-design operating modes. It is found that the greatest value of the efficiency rate is acquired at the design mode of operation of the traction nozzle, i.e. at S = 1.
- 1 January 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1741 (1) , 012004
Open AccessInfluence of the degree of off-design of the traction nozzle of a jet reaction turbine on its efficiency
At the present stage of social development, the need for rational use of energy resources of the planet is particularly acute. Most countries have already faced the problem of the energy crisis. An appropriate way to solve this problem is the utilization of secondary energy resources. With the help of turbine generators, it is possible to reduce the pressure and utilize the potential energy of excess pressure of gas or vapours to produce electricity. Such units can be created based on a jet reaction turbine. The study aims to assess the impact of the degree of off-design of the traction nozzle on the efficiency of the jet reactive turbine. The analysis of the factors influencing the efficiency of the jet reaction turbine is carried out in the work. The obtained efficiency rate for the jet reactive turbine depending on the given dimensionless velocity of λout t at the inlet pressure of the inlet nozzle of 2, 4, 6 and 10 MPa in the design mode (at the degree of off-design of S = 1) and in the off-design modes of operation ( S> 1). Graphical dependencies of the jet reaction turbine efficiency rate on the given circular velocity of the impeller are constructed (U− = 0… 0.7). The research shows that with increasing pressure at the inlet to the inlet nozzle, the efficiency rate of the turbine increases, and the optimum of the efficiency rate is shifted towards the increase of the given circular velocity of the impeller, both in the design and off-design operating modes. It is found that the greatest value of the efficiency rate is acquired at the design mode of operation of the traction nozzle, i.e. at S = 1.