Xiangwei Jin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiangwei Jin has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Junxin Hou
School of Materials Science and Chemical Engineering, Ningbo University 1 , Ningbo 315211
2 shared publications- Zhixiang Li
Key Laboratory of Marine Critical Materials, Ningbo Institute of Materials Technology & Engineering, Chinese Academy of Sciences, Ningbo, China
2 shared publications Aihua Sun
Zhejiang Key Laboratory of Additive Manufacturing Materials, Ningbo Institute of Materials Technology & Engineering, Chinese Academy of Sciences 2 , Ningbo 315201
1 shared publicationFenghua Liu
Key Laboratory of Marine Critical Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences 2 , Ningbo 315201
1 shared publicationGaojie Xu
Zhejiang Key Laboratory of Additive Manufacturing Materials, Ningbo Institute of Materials Technology & Engineering, Chinese Academy of Sciences 2 , Ningbo 315201
1 shared publicationJiawei Xu
Ningbo Haitian Laser Machinery Manufacturing Co, Ltd 4 , Ningbo 315800
1 shared publication
Latest Publications
- 7 April 2025
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 37 (2)
Investigation on the influence of particle size on the microstructure and properties of laser-cladded CuSn12 coatings
This study utilized laser cladding technology to fabricate copper alloy cladding layers on the surface of 42CrMo steel using CuSn12 powder with varying particle sizes (25–38, 45–75, and 75–150 μm). The influence of powder particle size on the morphology, microstructure, microhardness, and wear resistance of the cladding layer was investigated. Morphological analysis revealed that the cross section of the cladding layer produced with fine particles contained a significant number of pores distributed at the bottom and upper-middle regions of the layer; the layer fabricated with medium-sized particles exhibited a limited number of pores, primarily at the bottom; and the layer produced with coarse particles had a few unfused pores located at the interface with the substrate. Microhardness and wear resistance varied with changes in particle size, with the medium-sized particle cladding layer demonstrating superior performance in all evaluated properties.
- 7 April 2025
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 37 (2)
Investigation on the influence of particle size on the microstructure and properties of laser-cladded CuSn12 coatings
This study utilized laser cladding technology to fabricate copper alloy cladding layers on the surface of 42CrMo steel using CuSn12 powder with varying particle sizes (25–38, 45–75, and 75–150 μm). The influence of powder particle size on the morphology, microstructure, microhardness, and wear resistance of the cladding layer was investigated. Morphological analysis revealed that the cross section of the cladding layer produced with fine particles contained a significant number of pores distributed at the bottom and upper-middle regions of the layer; the layer fabricated with medium-sized particles exhibited a limited number of pores, primarily at the bottom; and the layer produced with coarse particles had a few unfused pores located at the interface with the substrate. Microhardness and wear resistance varied with changes in particle size, with the medium-sized particle cladding layer demonstrating superior performance in all evaluated properties.
- 9 December 2024
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 37 (1)
Research on the influence of titanium addition on the structure and frictional performance of laser clad tin bronze coating
Cu has a high infrared light reflectivity, which leads to the easy formation of defects such as pores in copper alloys during the laser cladding process. The purpose of this research is to reduce the porosity of tin bronze coatings during laser cladding by adding titanium elements with high infrared absorption. The porosity of the coating was characterized using scanning electron microscopy, metallographic microscopy, energy-dispersive spectroscopy, and x-ray diffraction. The research results indicate that as the content of titanium element increases, the porosity within the coating first decreases and then increases. When the titanium addition was 2%, the minimum porosity of the coating was 0.034%. The microhardness of the samples was tested using a semiautomatic Vickers hardness tester, and the reciprocating dry friction performance at room temperature was tested using a UMT-3 friction tester. The incorporation of titanium significantly enhances the microhardness and frictional properties of the laser-clad tin bronze coating. Therefore, this study provides experimental data support for controlling the porosity and frictional properties of laser-clad tin bronze coatings through elemental composition.
- 9 December 2024
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 37 (1)
Research on the influence of titanium addition on the structure and frictional performance of laser clad tin bronze coating
Cu has a high infrared light reflectivity, which leads to the easy formation of defects such as pores in copper alloys during the laser cladding process. The purpose of this research is to reduce the porosity of tin bronze coatings during laser cladding by adding titanium elements with high infrared absorption. The porosity of the coating was characterized using scanning electron microscopy, metallographic microscopy, energy-dispersive spectroscopy, and x-ray diffraction. The research results indicate that as the content of titanium element increases, the porosity within the coating first decreases and then increases. When the titanium addition was 2%, the minimum porosity of the coating was 0.034%. The microhardness of the samples was tested using a semiautomatic Vickers hardness tester, and the reciprocating dry friction performance at room temperature was tested using a UMT-3 friction tester. The incorporation of titanium significantly enhances the microhardness and frictional properties of the laser-clad tin bronze coating. Therefore, this study provides experimental data support for controlling the porosity and frictional properties of laser-clad tin bronze coatings through elemental composition.